Hi Simon,
On 12/19/22 20:20, Simon Glass wrote:
Hi Filip,
On Mon, 19 Dec 2022 at 02:29, Filip Žaludek <filip.zalu...@oracle.com> wrote:
Hi Simon,
is your testing framework connected to HDMI? Only notable discrepancy
from generic config is enabled 'efidebug' command.
Tested more (cycled 'U-Boot>' and 'reset'), both RPi3B and RPi3B+..
USB Keyboard failure rates:
connected console 02/10
connected hdmi 06/10
connected console + hdmi 07/10
** USB Keyboard always detected by 'usb info', just does not respond.
USB Keyboard failure rates, reverted 96991e652f541323a03c5b7e075d54a117091618:
connected console + hdmi 00/10
Yes this one does have HDMI. Are you wanting me to run multiple runs?
With or without the display?
Yes please! With HDMI as there is better chance you will hit issue I am
experiencing,
to confirm 96991e652f541323a03c5b7e075d54a117091618 is inferior for RPi3.
You should see usb_kbd detected, but no input possible.
Thanks,
Filip
Regards,
Simon
Just to note subsequent Grub2 menu redraw to my 180x50 console terminal
is about 5x faster when hdmi disconnected.
Thanks for testing!
Regards,
Filip
FW: rpi-firmware-20220830-1.0.1.el8.noarch
Revision: 9bd3d354a1a0712ac27c717df9ad60566b0406ee
On 12/17/22 23:24, Simon Glass wrote:
Hi Filip,
On Sat, 17 Dec 2022 at 05:50, Filip Žaludek <filip.zalu...@oracle.com> wrote:
Hello,
change seems to be unfriendly to RPi3B+, it allows to enter 'U-Boot>' shell
but usb keyboard
does not respond. Keyboard is detected by 'usb info' in v2023.01-rc3, not in
v2022.10.
When reverted, usb keyboard works as expected.
Anybody sitting front of RPi3B+ care to confirm?
Regards,
Filip
Patch:
https://urldefense.com/v3/__https://github.com/u-boot/u-boot/commit/96991e652f541323a03c5b7e075d54a117091618__;!!ACWV5N9M2RV99hQ!MunypRlNhelLw1nrbbLFCTeZK2pCAlIH_WPhgvmgFhfy3wJnPA5titNwl3o2fkc-mCqWAgJxjjc1sSD1$
Debug:
USB KBD: found interrupt EP: 0x81
USB KBD: set boot protocol
dwc2_submit_control_msg: dev='usb@7e980000', udev=000000003af4be00,
udev->dev='usb_kbd', portnr=3
USB KBD: set idle interval...
dwc2_submit_control_msg: dev='usb@7e980000', udev=000000003af4be00,
udev->dev='usb_kbd', portnr=3
USB KBD: enable interrupt pipe...
usb_kbd usb_kbd: Timeout poll on interrupt endpoint
Tested:
SW: v2022.10 & v2023.01-rc3 compiled from sources as 'rpiarm64'
HW: USB 1.1 and 2.0 keyboards, RPi3B+
JeOS:
https://urldefense.com/v3/__http://download.opensuse.org/ports/aarch64/tumbleweed/appliances/openSUSE-Tumbleweed-ARM-JeOS-raspberrypi.aarch64-2022.10.11-Snapshot20221112.raw.xz__;!!ACWV5N9M2RV99hQ!MunypRlNhelLw1nrbbLFCTeZK2pCAlIH_WPhgvmgFhfy3wJnPA5titNwl3o2fkc-mCqWAgJxjkilUmrv$
(u-boot-rpiarm64-2022.10-1.1.aarch64)
This seems to work on current master:
do-try-int.sh rpi3
Revision 9bd3d354a1a0712ac27c717df9ad60566b0406ee, board rpi3
Checking revision 9bd3d354a1a0712ac27c717df9ad60566b0406ee
/vid/software/devel/ubtest
tbot starting ...
├─Parameters:
│ rev = '9bd3d354a1a0712ac27c717df9ad60566b0406ee'
│ clean = False
├─Calling uboot_build_and_flash ...
│ ├─Calling uboot_build ...
│ │ ├─Calling uboot_checkout ...
│ │ │ ├─Builder: rpi3
│ │ │ └─Done. (0.181s)
│ │ ├─Configuring build ...
│ │ ├─Calling uboot_make ...
│ │ │ └─Done. (1.504s)
│ │ └─Done. (2.178s)
│ ├─Calling uboot_flash ...
│ │ ├─Calling copy ...
│ │ │ └─Done. (0.004s)
│ │ └─Done. (1.119s)
│ └─Done. (3.663s)
├─────────────────────────────────────────
└─SUCCESS (3.799s)
tbot starting ...
├─Calling interactive_board ...
│ ├─POWERON (rpi3)
│ ├─Entering interactive shell (CTRL+D to exit) ...
U-Boot 2023.01-rc3-00057-g9bd3d354a1a (Dec 17 2022 - 15:23:14 -0700)
DRAM: 992 MiB
RPI 3 Model B (0xa22082)
Core: 66 devices, 14 uclasses, devicetree: embed
MMC: mmc@7e202000: 0, mmc@7e300000: 1
Loading Environment from FAT... Unable to read "uboot.env" from mmc0:1...
In: serial
Out: vidconsole
Err: vidconsole
Net: No ethernet found.
starting USB...
Bus usb@7e980000: USB DWC2
scanning bus usb@7e980000 for devices... usb_kbd usb_kbd: Timeout poll
on interrupt endpoint
Failed to get keyboard state from device 0c40:8000
6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Hit any key to stop autoboot: 0
U-Boot> usb info
1: Hub, USB Revision 1.10
- U-Boot Root Hub
- Class: Hub
- PacketSize: 8 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 0.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 2 Interval 255ms
2: Hub, USB Revision 2.0
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0424 Product 0x9514 Version 2.0
Configuration: 1
- Interfaces: 1 Self Powered Remote Wakeup 2mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 1 Interval 12ms
- Endpoint 1 In Interrupt MaxPacket 1 Interval 12ms
3: Human Interface, USB Revision 1.10
- Logitech USB Keyboard
- Class: (from Interface) Human Interface
- PacketSize: 8 Configurations: 1
- Vendor: 0x046d Product 0xc31c Version 100.0
Configuration: 1
- Interfaces: 2 Bus Powered Remote Wakeup 90mA
- String: "U64.00_B0001"
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Human Interface, Subclass: Boot Keyboard
- String: "USB Keyboard"
- Endpoint 1 In Interrupt MaxPacket 8 Interval 10ms
Interface: 1
- Alternate Setting 0, Endpoints: 1
- Class Human Interface, Subclass: None
- String: "USB Keyboard"
- Endpoint 2 In Interrupt MaxPacket 4 Interval 255ms
4: Human Interface, USB Revision 0.1
- QDtech MPI5001 ?
- Class: (from Interface) Human Interface
- PacketSize: 64 Configurations: 1
- Vendor: 0x0483 Product 0x5750 Version 2.0
Configuration: 1
- Interfaces: 1 Bus Powered 64mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Human Interface, Subclass: None
- Endpoint 2 In Interrupt MaxPacket 64 Interval 1ms
- Endpoint 2 Out Interrupt MaxPacket 64 Interval 1ms
5: Vendor specific, USB Revision 2.0
- Class: Vendor specific
- PacketSize: 64 Configurations: 1
- Vendor: 0x0424 Product 0xec00 Version 2.0
Configuration: 1
- Interfaces: 1 Self Powered Remote Wakeup 2mA
Interface: 0
- Alternate Setting 0, Endpoints: 3
- Class Vendor specific
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512
- Endpoint 3 In Interrupt MaxPacket 16 Interval 4ms
6: Mass Storage, USB Revision 2.10
- SanDisk USB Extreme Pro 513456791960
- Class: (from Interface) Mass Storage
- PacketSize: 64 Configurations: 1
- Vendor: 0x0781 Product 0x5588 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 2
- Class Mass Storage, Transp. SCSI, Bulk only
- Endpoint 1 In Bulk MaxPacket 512
- Endpoint 2 Out Bulk MaxPacket 512
U-Boot> hello
Unknown command 'hello' - try 'help'
U-Boot>
│ ├─POWEROFF (rpi3)
│ ├─Exiting poweroff
│ └─Done. (34.381s)
├─────────────────────────────────────────
└─SUCCESS (34.481s)
(the 'hello' is typed on the keyboard)
Regards,
Simon
