Hi Quentin,
On 2023/2/6 19:26, Quentin Schulz wrote:
Hi Jonas,
On 2/5/23 21:21, Jonas Karlman wrote:
Rockchip SoCs typically use U-Boot TPL to initialize DRAM, then jumps
back to boot-rom to load the next stage of the boot flow, U-Boot SPL.
For RK356x there is currently no support to initialize DRAM using U-Boot
TPL and instead an external TPL binary must be used to generate a
working u-boot-rockchip.bin image.
Use the new external-tpl entry unless CONFIG_TPL=y to indicate that an
external TPL binary must be provided to generate a working firmware.
Signed-off-by: Jonas Karlman <jo...@kwiboo.se>
---
Makefile | 1 +
arch/arm/dts/rockchip-u-boot.dtsi | 16 ++++++++++++----
tools/binman/missing-blob-help | 5 +++++
3 files changed, 18 insertions(+), 4 deletions(-)
diff --git a/Makefile b/Makefile
index 7eaf45496c1c..7e9272be937f 100644
--- a/Makefile
+++ b/Makefile
@@ -1332,6 +1332,7 @@ cmd_binman = $(srctree)/tools/binman/binman
$(if $(BINMAN_DEBUG),-D) \
-a opensbi-path=${OPENSBI} \
-a default-dt=$(default_dt) \
-a scp-path=$(SCP) \
+ -a external-tpl-path=$(EXTERNAL_TPL) \
-a spl-bss-pad=$(if $(CONFIG_SPL_SEPARATE_BSS),,1) \
-a tpl-bss-pad=$(if $(CONFIG_TPL_SEPARATE_BSS),,1) \
-a spl-dtb=$(CONFIG_SPL_OF_REAL) \
diff --git a/arch/arm/dts/rockchip-u-boot.dtsi
b/arch/arm/dts/rockchip-u-boot.dtsi
index 6c662a72d4f9..bc3bc9bc3e37 100644
--- a/arch/arm/dts/rockchip-u-boot.dtsi
+++ b/arch/arm/dts/rockchip-u-boot.dtsi
@@ -20,12 +20,16 @@
mkimage {
filename = "idbloader.img";
args = "-n", CONFIG_SYS_SOC, "-T", "rksd";
-#ifdef CONFIG_TPL
multiple-data-files;
+#ifdef CONFIG_TPL
u-boot-tpl {
- };
+#else
+ external-tpl {
+ filename = "ddr.bin";
+ missing-msg = "external-tpl-rockchip";
#endif
+ };
NACK. This forces the use of a TPL (either built by U-Boot or
external) which is not always the case. There are still boards without
a TPL which work perfectly fine (at least I would hope so :) ).
Basically there are three possible cases:
SPL
TPL+SPL
TPL(external blob)+SPL
I'm afraid all the boards support by mainline U-Boot is using
"TPL(U-Boot or external)+SPL+U-Boot" mode, and this mode also always
used by rockchip vendor branch.
For "SPL+U-Boot" use case, it only happen many years ago in some of
rk3288 board and rk3399 board,
the SPL will need to support both sdram driver and storage(SPI, SDCard,
eMMC) driver and without back to BootRom,
and other function may add to SPL, but the sram size limit is always
there, so all the rk3288 and rk3399 board have migrate to use
"TPL+SPL+U-Boot.itb" mode.
The "TPL+SPL+U-Boot.itb" is much clear and easy to maintine for all the
boards and will be the only accept mode for new board support in the
future on rockchip platform:
- TPL for dram init;
- SPL for storage init and load next stage firmware, decode FIT image
with ATF/OPTEE support, secure boot support and etc;
- U-Boot.itb including ATF and U-Boot proper, maybe also OPTEE.
This model can very easy to do the debug with replace the binary from
rockchip vendor tree during board bringup.
The SPL+U-Boot mode can only happen for legacy board with only need
U-Boot raw image instead of itb which including trust support,
this kind of board can get the image with only one mkimage command, I
don't think it will need binman support because it only have one image.
Thanks,
- Kever
Here you remove the ability to have SPL only.
Hence why I suggested we add a new Kconfig option for EXTERNAL_TPL,
not for the path but to explicit this third possibility.
Cheers,
Quentin
u-boot-spl {
};
};
@@ -134,12 +138,16 @@
mkimage {
filename = "idbloader-spi.img";
args = "-n", CONFIG_SYS_SOC, "-T", "rkspi";
-#ifdef CONFIG_TPL
multiple-data-files;
+#ifdef CONFIG_TPL
u-boot-tpl {
- };
+#else
+ external-tpl {
+ filename = "ddr.bin";
+ missing-msg = "external-tpl-rockchip";
#endif
+ };
u-boot-spl {
};
};
diff --git a/tools/binman/missing-blob-help
b/tools/binman/missing-blob-help
index c61ca02a35ee..e850824032dd 100644
--- a/tools/binman/missing-blob-help
+++ b/tools/binman/missing-blob-help
@@ -14,6 +14,11 @@ atf-bl31-sunxi:
Please read the section on ARM Trusted Firmware (ATF) in
board/sunxi/README.sunxi64
+external-tpl-rockchip:
+External TPL is required to initialize DRAM. Get external TPL binary
and
+build with EXTERNAL_TPL=/path/to/ddr.bin. One possible source for
+external TPL binary is
https://urldefense.com/v3/__https://github.com/rockchip-linux/rkbin__;!!OOPJP91ZZw!jRwonQRHKoxzegx3S3cRYfalkhW1ESLyBCTmVc2c6fnmPaQBOZyxG2I7phwM3pEZxR2QIHQG8Hw3JStyx4tDcMsalwYDCg$
.
+
scp-sunxi:
SCP firmware is required for system suspend, but is otherwise
optional.
Please read the section on SCP firmware in board/sunxi/README.sunxi64
