From: Laurentiu Tudor <[email protected]> PPA was a secure firmware developed in-house which is no longer supported and replaced by TF-A quite some years ago. This makes the defconfigs that make use of PPA obsolete, so remove them.
Signed-off-by: Laurentiu Tudor <[email protected]> --- configs/ls1012a2g5rdb_qspi_defconfig | 69 --------- configs/ls1012afrdm_qspi_defconfig | 67 --------- .../ls1012afrwy_qspi_SECURE_BOOT_defconfig | 72 --------- configs/ls1012afrwy_qspi_defconfig | 72 --------- configs/ls1012aqds_qspi_defconfig | 95 ------------ configs/ls1012ardb_qspi_SECURE_BOOT_defconfig | 77 ---------- configs/ls1012ardb_qspi_defconfig | 77 ---------- configs/ls1043aqds_defconfig | 107 -------------- configs/ls1043aqds_lpuart_defconfig | 109 -------------- configs/ls1043aqds_nand_defconfig | 138 ------------------ configs/ls1043aqds_nor_ddr3_defconfig | 108 -------------- configs/ls1043aqds_qspi_defconfig | 98 ------------- configs/ls1043aqds_sdcard_ifc_defconfig | 135 ----------------- configs/ls1043aqds_sdcard_qspi_defconfig | 124 ---------------- configs/ls1043ardb_SECURE_BOOT_defconfig | 99 ------------- configs/ls1043ardb_defconfig | 100 ------------- configs/ls1043ardb_nand_SECURE_BOOT_defconfig | 124 ---------------- configs/ls1043ardb_nand_defconfig | 128 ---------------- .../ls1043ardb_sdcard_SECURE_BOOT_defconfig | 124 ---------------- configs/ls1043ardb_sdcard_defconfig | 126 ---------------- configs/ls2080aqds_SECURE_BOOT_defconfig | 108 -------------- configs/ls2080aqds_defconfig | 109 -------------- configs/ls2080aqds_sdcard_defconfig | 116 --------------- configs/ls2080ardb_SECURE_BOOT_defconfig | 106 -------------- configs/ls2080ardb_defconfig | 107 -------------- 25 files changed, 2595 deletions(-) delete mode 100644 configs/ls1012a2g5rdb_qspi_defconfig delete mode 100644 configs/ls1012afrdm_qspi_defconfig delete mode 100644 configs/ls1012afrwy_qspi_SECURE_BOOT_defconfig delete mode 100644 configs/ls1012afrwy_qspi_defconfig delete mode 100644 configs/ls1012aqds_qspi_defconfig delete mode 100644 configs/ls1012ardb_qspi_SECURE_BOOT_defconfig delete mode 100644 configs/ls1012ardb_qspi_defconfig delete mode 100644 configs/ls1043aqds_defconfig delete mode 100644 configs/ls1043aqds_lpuart_defconfig delete mode 100644 configs/ls1043aqds_nand_defconfig delete mode 100644 configs/ls1043aqds_nor_ddr3_defconfig delete mode 100644 configs/ls1043aqds_qspi_defconfig delete mode 100644 configs/ls1043aqds_sdcard_ifc_defconfig delete mode 100644 configs/ls1043aqds_sdcard_qspi_defconfig delete mode 100644 configs/ls1043ardb_SECURE_BOOT_defconfig delete mode 100644 configs/ls1043ardb_defconfig delete mode 100644 configs/ls1043ardb_nand_SECURE_BOOT_defconfig delete mode 100644 configs/ls1043ardb_nand_defconfig delete mode 100644 configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig delete mode 100644 configs/ls1043ardb_sdcard_defconfig delete mode 100644 configs/ls2080aqds_SECURE_BOOT_defconfig delete mode 100644 configs/ls2080aqds_defconfig delete mode 100644 configs/ls2080aqds_sdcard_defconfig delete mode 100644 configs/ls2080ardb_SECURE_BOOT_defconfig delete mode 100644 configs/ls2080ardb_defconfig diff --git a/configs/ls1012a2g5rdb_qspi_defconfig b/configs/ls1012a2g5rdb_qspi_defconfig deleted file mode 100644 index 72b590a73b4c..000000000000 --- a/configs/ls1012a2g5rdb_qspi_defconfig +++ /dev/null @@ -1,69 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1012A2G5RDB=y -CONFIG_TEXT_BASE=0x40100000 -CONFIG_SYS_MALLOC_LEN=0x500000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x300000 -CONFIG_ENV_SECT_SIZE=0x40000 -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-2g5rdb" -CONFIG_FSL_LS_PPA=y -CONFIG_QSPI_AHB_INIT=y -CONFIG_AHCI=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_QSPI_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000" -CONFIG_BOOTCOMMAND="run distro_bootcmd; run qspi_bootcmd; env exists secureboot && esbc_halt;" -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_DISPLAY_BOARDINFO_LATE=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_GREPENV=y -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_SATA=y -CONFIG_SCSI_AHCI=y -CONFIG_SATA_CEVA=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_DM_SPI_FLASH=y -# CONFIG_SPI_FLASH_BAR is not set -CONFIG_SPI_FLASH_SPANSION=y -# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set -CONFIG_FSL_PFE=y -CONFIG_DM_RTC=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_QSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls1012afrdm_qspi_defconfig b/configs/ls1012afrdm_qspi_defconfig deleted file mode 100644 index 7e12f6ef546b..000000000000 --- a/configs/ls1012afrdm_qspi_defconfig +++ /dev/null @@ -1,67 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1012AFRDM=y -CONFIG_TEXT_BASE=0x40100000 -CONFIG_SYS_MALLOC_LEN=0x500000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x300000 -CONFIG_ENV_SECT_SIZE=0x40000 -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-frdm" -CONFIG_FSL_LS_PPA=y -CONFIG_QSPI_AHB_INIT=y -CONFIG_PCI=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_QSPI_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000" -CONFIG_BOOTCOMMAND="run distro_bootcmd;run qspi_bootcmd" -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_DISPLAY_BOARDINFO_LATE=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_GREPENV=y -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -# CONFIG_MMC is not set -CONFIG_MTD=y -CONFIG_DM_SPI_FLASH=y -# CONFIG_SPI_FLASH_BAR is not set -CONFIG_SPI_FLASH_SPANSION=y -# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set -CONFIG_FSL_PFE=y -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_RTC=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_QSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls1012afrwy_qspi_SECURE_BOOT_defconfig b/configs/ls1012afrwy_qspi_SECURE_BOOT_defconfig deleted file mode 100644 index 4e5079dcc492..000000000000 --- a/configs/ls1012afrwy_qspi_SECURE_BOOT_defconfig +++ /dev/null @@ -1,72 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1012AFRWY=y -CONFIG_TEXT_BASE=0x40100000 -CONFIG_SYS_MALLOC_LEN=0x500000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-frwy" -CONFIG_FSL_LS_PPA=y -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_NXP_ESBC=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_QSPI_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000" -CONFIG_BOOTCOMMAND="run distro_bootcmd; run sd_bootcmd; env exists secureboot && esbc_halt;" -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_DISPLAY_BOARDINFO_LATE=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_GREPENV=y -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_PCI=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_FSL_SEC_MON_BE=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_DM_SPI_FLASH=y -# CONFIG_SPI_FLASH_BAR is not set -CONFIG_SPI_FLASH_WINBOND=y -CONFIG_FSL_PFE=y -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_RTC=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_QSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y -CONFIG_RSA=y -CONFIG_RSA_SOFTWARE_EXP=y diff --git a/configs/ls1012afrwy_qspi_defconfig b/configs/ls1012afrwy_qspi_defconfig deleted file mode 100644 index b944f803f70c..000000000000 --- a/configs/ls1012afrwy_qspi_defconfig +++ /dev/null @@ -1,72 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1012AFRWY=y -CONFIG_TEXT_BASE=0x40100000 -CONFIG_SYS_MALLOC_LEN=0x500000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x1D0000 -CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-frwy" -CONFIG_FSL_LS_PPA=y -CONFIG_ENV_ADDR=0x401D0000 -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_QSPI_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000" -CONFIG_BOOTCOMMAND="run distro_bootcmd; run sd_bootcmd; env exists secureboot && esbc_halt;" -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_DISPLAY_BOARDINFO_LATE=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_GREPENV=y -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_PCI=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_DM_SPI_FLASH=y -CONFIG_SPI_FLASH_WINBOND=y -CONFIG_FSL_PFE=y -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_RTC=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls1012aqds_qspi_defconfig b/configs/ls1012aqds_qspi_defconfig deleted file mode 100644 index 34bdb1abafc7..000000000000 --- a/configs/ls1012aqds_qspi_defconfig +++ /dev/null @@ -1,95 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1012AQDS=y -CONFIG_TEXT_BASE=0x40100000 -CONFIG_SYS_MALLOC_LEN=0x500000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_SF_DEFAULT_SPEED=10000000 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x300000 -CONFIG_ENV_SECT_SIZE=0x40000 -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-qds" -CONFIG_FSL_LS_PPA=y -CONFIG_QSPI_AHB_INIT=y -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_FSL_QIXIS=y -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_QSPI_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000" -CONFIG_BOOTCOMMAND="run distro_bootcmd; run qspi_bootcmd; env exists secureboot && esbc_halt;" -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_DISPLAY_BOARDINFO_LATE=y -CONFIG_MISC_INIT_R=y -CONFIG_ID_EEPROM=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_GREPENV=y -CONFIG_CMD_EEPROM=y -CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3 -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_PCI=y -CONFIG_CMD_SPI=y -CONFIG_DEFAULT_SPI_BUS=1 -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_ENV_SPI_BUS=0 -CONFIG_ENV_SPI_MAX_HZ=1000000 -CONFIG_ENV_SPI_MODE=0x03 -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_SATA=y -CONFIG_SCSI_AHCI=y -CONFIG_SATA_CEVA=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_DM_SPI_FLASH=y -CONFIG_SF_DEFAULT_BUS=1 -# CONFIG_SPI_FLASH_BAR is not set -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_SPANSION=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set -CONFIG_FSL_PFE=y -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_RTC=y -CONFIG_RTC_PCF8563=y -CONFIG_SCSI=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_DSPI=y -CONFIG_FSL_QSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls1012ardb_qspi_SECURE_BOOT_defconfig b/configs/ls1012ardb_qspi_SECURE_BOOT_defconfig deleted file mode 100644 index dcd18b4eb8cc..000000000000 --- a/configs/ls1012ardb_qspi_SECURE_BOOT_defconfig +++ /dev/null @@ -1,77 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1012ARDB=y -CONFIG_TEXT_BASE=0x40100000 -CONFIG_SYS_MALLOC_LEN=0x500000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-rdb" -CONFIG_FSL_LS_PPA=y -CONFIG_QSPI_AHB_INIT=y -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_NXP_ESBC=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_QSPI_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000" -CONFIG_BOOTCOMMAND="run distro_bootcmd; run qspi_bootcmd; env exists secureboot && esbc_halt;" -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_DISPLAY_BOARDINFO_LATE=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_GREPENV=y -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_PCI=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_FSL_SEC_MON_BE=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_DM_SPI_FLASH=y -# CONFIG_SPI_FLASH_BAR is not set -CONFIG_SPI_FLASH_SPANSION=y -# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_RTC=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_DSPI=y -CONFIG_FSL_QSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y -CONFIG_RSA=y -CONFIG_RSA_SOFTWARE_EXP=y diff --git a/configs/ls1012ardb_qspi_defconfig b/configs/ls1012ardb_qspi_defconfig deleted file mode 100644 index 10fe826f99a0..000000000000 --- a/configs/ls1012ardb_qspi_defconfig +++ /dev/null @@ -1,77 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1012ARDB=y -CONFIG_TEXT_BASE=0x40100000 -CONFIG_SYS_MALLOC_LEN=0x500000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x300000 -CONFIG_ENV_SECT_SIZE=0x40000 -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1012a-rdb" -CONFIG_FSL_LS_PPA=y -CONFIG_QSPI_AHB_INIT=y -CONFIG_ENV_ADDR=0x40300000 -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -# CONFIG_SYS_MALLOC_F is not set -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_QSPI_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 quiet lpj=250000" -CONFIG_BOOTCOMMAND="run distro_bootcmd; run qspi_bootcmd; env exists secureboot && esbc_halt;" -# CONFIG_DISPLAY_BOARDINFO is not set -CONFIG_DISPLAY_BOARDINFO_LATE=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_GREPENV=y -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_PCI=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_DM_SPI_FLASH=y -# CONFIG_SPI_FLASH_BAR is not set -CONFIG_SPI_FLASH_SPANSION=y -# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set -CONFIG_FSL_PFE=y -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_RTC=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_DSPI=y -CONFIG_FSL_QSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls1043aqds_defconfig b/configs/ls1043aqds_defconfig deleted file mode 100644 index 18bf4bd8792c..000000000000 --- a/configs/ls1043aqds_defconfig +++ /dev/null @@ -1,107 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043AQDS=y -CONFIG_TEXT_BASE=0x60100000 -CONFIG_SYS_MALLOC_LEN=0x120000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x20000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_SYS_I2C_MXC_I2C1=y -CONFIG_SYS_I2C_MXC_I2C2=y -CONFIG_SYS_I2C_MXC_I2C3=y -CONFIG_SYS_I2C_MXC_I2C4=y -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart" -CONFIG_FSL_LS_PPA=y -CONFIG_ENV_ADDR=0x60300000 -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_FSL_USE_PCA9547_MUX=y -CONFIG_VID=y -CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv" -CONFIG_VOL_MONITOR_INA220=y -CONFIG_VOL_MONITOR_IR36021_SET=y -CONFIG_FSL_QIXIS=y -# CONFIG_QIXIS_I2C_ACCESS is not set -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_DYNAMIC_SYS_CLK_FREQ=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_USE_BOOTCOMMAND is not set -CONFIG_ARCH_MISC_INIT=y -CONFIG_MISC_INIT_R=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_BOOTZ=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_FSL_CAAM=y -CONFIG_DYNAMIC_DDR_CLK_FREQ=y -CONFIG_DDR_ECC=y -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_SPL_SYS_I2C_LEGACY=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SF_DEFAULT_BUS=1 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls1043aqds_lpuart_defconfig b/configs/ls1043aqds_lpuart_defconfig deleted file mode 100644 index 9dcbe71ad0c1..000000000000 --- a/configs/ls1043aqds_lpuart_defconfig +++ /dev/null @@ -1,109 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043AQDS=y -CONFIG_TEXT_BASE=0x60100000 -CONFIG_SYS_MALLOC_LEN=0x120000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x20000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_SYS_I2C_MXC_I2C1=y -CONFIG_SYS_I2C_MXC_I2C2=y -CONFIG_SYS_I2C_MXC_I2C3=y -CONFIG_SYS_I2C_MXC_I2C4=y -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-lpuart" -CONFIG_FSL_LS_PPA=y -CONFIG_ENV_ADDR=0x60300000 -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_FSL_USE_PCA9547_MUX=y -CONFIG_VID=y -CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv" -CONFIG_VOL_MONITOR_INA220=y -CONFIG_VOL_MONITOR_IR36021_SET=y -CONFIG_FSL_QIXIS=y -# CONFIG_QIXIS_I2C_ACCESS is not set -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_DYNAMIC_SYS_CLK_FREQ=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_USE_BOOTCOMMAND is not set -CONFIG_ARCH_MISC_INIT=y -CONFIG_MISC_INIT_R=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_BOOTZ=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_FSL_CAAM=y -CONFIG_DYNAMIC_DDR_CLK_FREQ=y -CONFIG_DDR_ECC=y -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_SPL_SYS_I2C_LEGACY=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SF_DEFAULT_BUS=1 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_SCSI=y -CONFIG_DM_SERIAL=y -CONFIG_FSL_LPUART=y -CONFIG_LPUART=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls1043aqds_nand_defconfig b/configs/ls1043aqds_nand_defconfig deleted file mode 100644 index e5f570a3b3c1..000000000000 --- a/configs/ls1043aqds_nand_defconfig +++ /dev/null @@ -1,138 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043AQDS=y -CONFIG_TEXT_BASE=0x82000000 -CONFIG_SYS_MALLOC_LEN=0x102000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x300000 -CONFIG_SYS_I2C_MXC_I2C1=y -CONFIG_SYS_I2C_MXC_I2C2=y -CONFIG_SYS_I2C_MXC_I2C3=y -CONFIG_SYS_I2C_MXC_I2C4=y -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart" -CONFIG_SPL_TEXT_BASE=0x10000000 -CONFIG_FSL_LS_PPA=y -CONFIG_SYS_MONITOR_LEN=1048576 -CONFIG_SPL_SERIAL=y -CONFIG_SPL_DRIVERS_MISC=y -CONFIG_SPL_STACK=0x1001d000 -CONFIG_SPL=y -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_FSL_USE_PCA9547_MUX=y -CONFIG_VID=y -CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv" -CONFIG_VOL_MONITOR_INA220=y -CONFIG_VOL_MONITOR_IR36021_SET=y -CONFIG_FSL_QIXIS=y -# CONFIG_QIXIS_I2C_ACCESS is not set -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_DYNAMIC_SYS_CLK_FREQ=y -CONFIG_RAMBOOT_PBL=y -CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043aqds/ls1043aqds_pbi.cfg" -CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043aqds/ls1043aqds_rcw_nand.cfg" -CONFIG_DISTRO_DEFAULTS=y -CONFIG_NAND_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_USE_BOOTCOMMAND is not set -CONFIG_ARCH_MISC_INIT=y -CONFIG_MISC_INIT_R=y -CONFIG_SPL_MAX_SIZE=0x1a000 -CONFIG_SPL_PAD_TO=0x20000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x80100000 -CONFIG_SPL_BSS_MAX_SIZE=0x80000 -CONFIG_SPL_FSL_PBL=y -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SYS_SPL_MALLOC=y -CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y -CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x80200000 -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xf0 -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C=y -CONFIG_SPL_MPC8XXX_INIT_DDR=y -CONFIG_SPL_NAND_SUPPORT=y -CONFIG_SPL_WATCHDOG=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_BOOTZ=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_SPL_EFI_PARTITION is not set -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_NAND=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_FSL_CAAM=y -CONFIG_DYNAMIC_DDR_CLK_FREQ=y -CONFIG_DDR_ECC=y -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_SPL_SYS_I2C_LEGACY=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y -CONFIG_SYS_NAND_U_BOOT_OFFS=0x20000 -CONFIG_SF_DEFAULT_BUS=1 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls1043aqds_nor_ddr3_defconfig b/configs/ls1043aqds_nor_ddr3_defconfig deleted file mode 100644 index 67d8288abb00..000000000000 --- a/configs/ls1043aqds_nor_ddr3_defconfig +++ /dev/null @@ -1,108 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043AQDS=y -CONFIG_TEXT_BASE=0x60100000 -CONFIG_SYS_MALLOC_LEN=0x120000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x20000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_SYS_I2C_MXC_I2C1=y -CONFIG_SYS_I2C_MXC_I2C2=y -CONFIG_SYS_I2C_MXC_I2C3=y -CONFIG_SYS_I2C_MXC_I2C4=y -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart" -CONFIG_FSL_LS_PPA=y -CONFIG_ENV_ADDR=0x60300000 -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_FSL_USE_PCA9547_MUX=y -CONFIG_VID=y -CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv" -CONFIG_VOL_MONITOR_INA220=y -CONFIG_VOL_MONITOR_IR36021_SET=y -CONFIG_FSL_QIXIS=y -# CONFIG_QIXIS_I2C_ACCESS is not set -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_DYNAMIC_SYS_CLK_FREQ=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_USE_BOOTCOMMAND is not set -CONFIG_ARCH_MISC_INIT=y -CONFIG_MISC_INIT_R=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_BOOTZ=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_FSL_CAAM=y -CONFIG_DYNAMIC_DDR_CLK_FREQ=y -CONFIG_SYS_FSL_DDR3=y -CONFIG_DDR_ECC=y -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_SPL_SYS_I2C_LEGACY=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SF_DEFAULT_BUS=1 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls1043aqds_qspi_defconfig b/configs/ls1043aqds_qspi_defconfig deleted file mode 100644 index fa0b47fde8c4..000000000000 --- a/configs/ls1043aqds_qspi_defconfig +++ /dev/null @@ -1,98 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043AQDS=y -CONFIG_TEXT_BASE=0x40100000 -CONFIG_SYS_MALLOC_LEN=0x102000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x300000 -CONFIG_ENV_SECT_SIZE=0x10000 -CONFIG_SYS_I2C_MXC_I2C1=y -CONFIG_SYS_I2C_MXC_I2C2=y -CONFIG_SYS_I2C_MXC_I2C3=y -CONFIG_SYS_I2C_MXC_I2C4=y -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart" -CONFIG_FSL_LS_PPA=y -CONFIG_ENV_ADDR=0x40300000 -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_FSL_USE_PCA9547_MUX=y -CONFIG_VID=y -CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv" -CONFIG_VOL_MONITOR_INA220=y -CONFIG_VOL_MONITOR_IR36021_SET=y -CONFIG_FSL_QIXIS=y -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_DYNAMIC_SYS_CLK_FREQ=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_QSPI_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_USE_BOOTCOMMAND is not set -CONFIG_ARCH_MISC_INIT=y -CONFIG_MISC_INIT_R=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_BOOTZ=y -CONFIG_CMD_GREPENV=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_SPI_FLASH=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_FSL_CAAM=y -CONFIG_DYNAMIC_DDR_CLK_FREQ=y -CONFIG_DDR_ECC=y -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_SPL_SYS_I2C_LEGACY=y -CONFIG_SYS_I2C_EARLY_INIT=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -# CONFIG_SPI_FLASH_BAR is not set -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_SPANSION=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_QSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls1043aqds_sdcard_ifc_defconfig b/configs/ls1043aqds_sdcard_ifc_defconfig deleted file mode 100644 index 6cb961d33dcc..000000000000 --- a/configs/ls1043aqds_sdcard_ifc_defconfig +++ /dev/null @@ -1,135 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043AQDS=y -CONFIG_TEXT_BASE=0x82000000 -CONFIG_SYS_MALLOC_LEN=0x102000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x300000 -CONFIG_SYS_I2C_MXC_I2C1=y -CONFIG_SYS_I2C_MXC_I2C2=y -CONFIG_SYS_I2C_MXC_I2C3=y -CONFIG_SYS_I2C_MXC_I2C4=y -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart" -CONFIG_SPL_TEXT_BASE=0x10000000 -CONFIG_FSL_LS_PPA=y -CONFIG_SYS_MONITOR_LEN=1048576 -CONFIG_SPL_MMC=y -CONFIG_SPL_SERIAL=y -CONFIG_SPL_DRIVERS_MISC=y -CONFIG_SPL_STACK=0x1001e000 -CONFIG_SPL=y -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_FSL_USE_PCA9547_MUX=y -CONFIG_VID=y -CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv" -CONFIG_VOL_MONITOR_INA220=y -CONFIG_VOL_MONITOR_IR36021_SET=y -CONFIG_FSL_QIXIS=y -# CONFIG_QIXIS_I2C_ACCESS is not set -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_DYNAMIC_SYS_CLK_FREQ=y -CONFIG_RAMBOOT_PBL=y -CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043aqds/ls1043aqds_pbi.cfg" -CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043aqds/ls1043aqds_rcw_sd_ifc.cfg" -CONFIG_DISTRO_DEFAULTS=y -CONFIG_SD_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_USE_BOOTCOMMAND is not set -CONFIG_ARCH_MISC_INIT=y -CONFIG_MISC_INIT_R=y -CONFIG_SPL_MAX_SIZE=0x17000 -CONFIG_SPL_PAD_TO=0x1d000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x8f000000 -CONFIG_SPL_BSS_MAX_SIZE=0x80000 -CONFIG_SPL_FSL_PBL=y -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SYS_SPL_MALLOC=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xf0 -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C=y -CONFIG_SPL_MPC8XXX_INIT_DDR=y -CONFIG_SPL_WATCHDOG=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_BOOTZ=y -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_SPL_EFI_PARTITION is not set -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_MMC=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_FSL_CAAM=y -CONFIG_DYNAMIC_DDR_CLK_FREQ=y -CONFIG_DDR_ECC=y -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_SPL_SYS_I2C_LEGACY=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SF_DEFAULT_BUS=1 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls1043aqds_sdcard_qspi_defconfig b/configs/ls1043aqds_sdcard_qspi_defconfig deleted file mode 100644 index 4e41508251da..000000000000 --- a/configs/ls1043aqds_sdcard_qspi_defconfig +++ /dev/null @@ -1,124 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043AQDS=y -CONFIG_TEXT_BASE=0x82000000 -CONFIG_SYS_MALLOC_LEN=0x102000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x300000 -CONFIG_SYS_I2C_MXC_I2C1=y -CONFIG_SYS_I2C_MXC_I2C2=y -CONFIG_SYS_I2C_MXC_I2C3=y -CONFIG_SYS_I2C_MXC_I2C4=y -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-qds-duart" -CONFIG_SPL_TEXT_BASE=0x10000000 -CONFIG_FSL_LS_PPA=y -CONFIG_SYS_MONITOR_LEN=1048576 -CONFIG_SPL_MMC=y -CONFIG_SPL_SERIAL=y -CONFIG_SPL_DRIVERS_MISC=y -CONFIG_SPL_STACK=0x1001e000 -CONFIG_SPL=y -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_FSL_USE_PCA9547_MUX=y -CONFIG_VID=y -CONFIG_VID_FLS_ENV="ls1043aqds_vdd_mv" -CONFIG_VOL_MONITOR_INA220=y -CONFIG_VOL_MONITOR_IR36021_SET=y -CONFIG_FSL_QIXIS=y -CONFIG_SYS_MEMTEST_START=0x80000000 -CONFIG_SYS_MEMTEST_END=0x9fffffff -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_DYNAMIC_SYS_CLK_FREQ=y -CONFIG_RAMBOOT_PBL=y -CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043aqds/ls1043aqds_pbi.cfg" -CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043aqds/ls1043aqds_rcw_sd_qspi.cfg" -CONFIG_DISTRO_DEFAULTS=y -CONFIG_SD_BOOT=y -CONFIG_SD_BOOT_QSPI=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_USE_BOOTCOMMAND is not set -CONFIG_ARCH_MISC_INIT=y -CONFIG_MISC_INIT_R=y -CONFIG_SPL_MAX_SIZE=0x17000 -CONFIG_SPL_PAD_TO=0x1d000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x8f000000 -CONFIG_SPL_BSS_MAX_SIZE=0x80000 -CONFIG_SPL_FSL_PBL=y -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SYS_SPL_MALLOC=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xf0 -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C=y -CONFIG_SPL_MPC8XXX_INIT_DDR=y -CONFIG_SPL_WATCHDOG=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_BOOTZ=y -CONFIG_CMD_GREPENV=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_MEMINFO=y -CONFIG_CMD_MEMTEST=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_SPL_EFI_PARTITION is not set -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_MMC=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_FSL_CAAM=y -CONFIG_DYNAMIC_DDR_CLK_FREQ=y -CONFIG_DDR_ECC=y -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_SPL_SYS_I2C_LEGACY=y -CONFIG_SYS_I2C_EARLY_INIT=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -# CONFIG_SPI_FLASH_BAR is not set -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_SPANSION=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_E1000=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_QSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls1043ardb_SECURE_BOOT_defconfig b/configs/ls1043ardb_SECURE_BOOT_defconfig deleted file mode 100644 index ea195d7c5041..000000000000 --- a/configs/ls1043ardb_SECURE_BOOT_defconfig +++ /dev/null @@ -1,99 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043ARDB=y -CONFIG_TEXT_BASE=0x60100000 -CONFIG_SYS_MALLOC_LEN=0x120000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x20000 -CONFIG_SYS_I2C_MXC_I2C1=y -CONFIG_SYS_I2C_MXC_I2C2=y -CONFIG_SYS_I2C_MXC_I2C3=y -CONFIG_SYS_I2C_MXC_I2C4=y -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb" -CONFIG_FSL_LS_PPA=y -CONFIG_PCI=y -CONFIG_OF_BOARD_FIXUP=y -CONFIG_NXP_ESBC=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -CONFIG_BOOTCOMMAND="run distro_bootcmd; run nor_bootcmd; env exists secureboot && esbc_halt;" -CONFIG_MISC_INIT_R=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_IMLS=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_DM=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_USE_ETHPRIME=y -CONFIG_ETHPRIME="FM1@DTSEC3" -# CONFIG_DDR_SPD is not set -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_SYS_DDR_RAW_TIMING=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_SPL_SYS_I2C_LEGACY=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_FSL_SEC_MON_BE=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x53 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SF_DEFAULT_BUS=1 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_DM_MDIO=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_SYS_FMAN_FW_ADDR=0x60900000 -CONFIG_NVME_PCI=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_SYS_QE_FW_ADDR=0x60940000 -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SPECIFY_CONSOLE_INDEX=y -CONFIG_DM_SERIAL=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y -CONFIG_RSA=y -CONFIG_RSA_SOFTWARE_EXP=y -CONFIG_EFI_LOADER_BOUNCE_BUFFER=y diff --git a/configs/ls1043ardb_defconfig b/configs/ls1043ardb_defconfig deleted file mode 100644 index ae8600ffd958..000000000000 --- a/configs/ls1043ardb_defconfig +++ /dev/null @@ -1,100 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043ARDB=y -CONFIG_TEXT_BASE=0x60100000 -CONFIG_SYS_MALLOC_LEN=0x120000 -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x20000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_SYS_I2C_MXC_I2C1=y -CONFIG_SYS_I2C_MXC_I2C2=y -CONFIG_SYS_I2C_MXC_I2C3=y -CONFIG_SYS_I2C_MXC_I2C4=y -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb" -CONFIG_FSL_LS_PPA=y -CONFIG_ENV_ADDR=0x60300000 -CONFIG_PCI=y -CONFIG_OF_BOARD_FIXUP=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_DISTRO_DEFAULTS=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -CONFIG_BOOTCOMMAND="run distro_bootcmd; run nor_bootcmd; env exists secureboot && esbc_halt;" -CONFIG_ARCH_MISC_INIT=y -CONFIG_MISC_INIT_R=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_IMLS=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_DM=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_USE_ETHPRIME=y -CONFIG_ETHPRIME="FM1@DTSEC3" -CONFIG_FSL_CAAM=y -# CONFIG_DDR_SPD is not set -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_SYS_DDR_RAW_TIMING=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_SPL_SYS_I2C_LEGACY=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x53 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SF_DEFAULT_BUS=1 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHY_AQUANTIA=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_DM_MDIO=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_SYS_FMAN_FW_ADDR=0x60900000 -CONFIG_NVME_PCI=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_SYS_QE_FW_ADDR=0x60940000 -CONFIG_SYS_QE_FMAN_FW_IN_NOR=y -CONFIG_SPECIFY_CONSOLE_INDEX=y -CONFIG_DM_SERIAL=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y -CONFIG_EFI_LOADER_BOUNCE_BUFFER=y diff --git a/configs/ls1043ardb_nand_SECURE_BOOT_defconfig b/configs/ls1043ardb_nand_SECURE_BOOT_defconfig deleted file mode 100644 index d9ff0fd16a58..000000000000 --- a/configs/ls1043ardb_nand_SECURE_BOOT_defconfig +++ /dev/null @@ -1,124 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043ARDB=y -CONFIG_TEXT_BASE=0x82000000 -CONFIG_SYS_MALLOC_LEN=0x102000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb" -CONFIG_SPL_TEXT_BASE=0x10000000 -CONFIG_FSL_LS_PPA=y -CONFIG_SYS_MONITOR_LEN=1064960 -CONFIG_SPL_SERIAL=y -CONFIG_SPL_DRIVERS_MISC=y -CONFIG_SPL_STACK=0x1001d000 -CONFIG_SPL=y -CONFIG_PCI=y -CONFIG_OF_BOARD_FIXUP=y -CONFIG_NXP_ESBC=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_RAMBOOT_PBL=y -CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043ardb/ls1043ardb_pbi.cfg" -CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043ardb/ls1043ardb_rcw_nand.cfg" -CONFIG_DISTRO_DEFAULTS=y -CONFIG_NAND_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_USE_BOOTCOMMAND is not set -CONFIG_MISC_INIT_R=y -CONFIG_SPL_MAX_SIZE=0x1a000 -CONFIG_SPL_PAD_TO=0x20000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x80100000 -CONFIG_SPL_BSS_MAX_SIZE=0x80000 -CONFIG_SPL_FSL_PBL=y -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SYS_SPL_MALLOC=y -CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y -CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x80200000 -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xf0 -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR=y -CONFIG_SPL_NAND_SUPPORT=y -CONFIG_SPL_WATCHDOG=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_IMLS=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_DM=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_SPL_EFI_PARTITION is not set -CONFIG_OF_CONTROL=y -CONFIG_SPL_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_USE_ETHPRIME=y -CONFIG_ETHPRIME="FM1@DTSEC3" -CONFIG_SPL_DM=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_FSL_SEC_MON_BE=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x53 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y -CONFIG_SYS_NAND_U_BOOT_OFFS=0x20000 -CONFIG_SF_DEFAULT_BUS=1 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHY_AQUANTIA=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_DM_MDIO=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_SYS_FMAN_FW_ADDR=0x900000 -CONFIG_NVME_PCI=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_SYS_QE_FMAN_FW_IN_NAND=y -CONFIG_SPECIFY_CONSOLE_INDEX=y -CONFIG_DM_SERIAL=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y -# CONFIG_SPL_USE_TINY_PRINTF is not set -CONFIG_RSA=y -CONFIG_SPL_RSA=y -CONFIG_EFI_LOADER_BOUNCE_BUFFER=y diff --git a/configs/ls1043ardb_nand_defconfig b/configs/ls1043ardb_nand_defconfig deleted file mode 100644 index ad118187432e..000000000000 --- a/configs/ls1043ardb_nand_defconfig +++ /dev/null @@ -1,128 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043ARDB=y -CONFIG_TEXT_BASE=0x82000000 -CONFIG_SYS_MALLOC_LEN=0x102000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x300000 -CONFIG_SYS_I2C_MXC_I2C1=y -CONFIG_SYS_I2C_MXC_I2C2=y -CONFIG_SYS_I2C_MXC_I2C3=y -CONFIG_SYS_I2C_MXC_I2C4=y -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb" -CONFIG_SPL_TEXT_BASE=0x10000000 -CONFIG_FSL_LS_PPA=y -CONFIG_SYS_MONITOR_LEN=1048576 -CONFIG_SPL_SERIAL=y -CONFIG_SPL_DRIVERS_MISC=y -CONFIG_SPL_STACK=0x1001d000 -CONFIG_SPL=y -CONFIG_PCI=y -CONFIG_OF_BOARD_FIXUP=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_RAMBOOT_PBL=y -CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043ardb/ls1043ardb_pbi.cfg" -CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043ardb/ls1043ardb_rcw_nand.cfg" -CONFIG_DISTRO_DEFAULTS=y -CONFIG_NAND_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_USE_BOOTCOMMAND is not set -CONFIG_ARCH_MISC_INIT=y -CONFIG_MISC_INIT_R=y -CONFIG_SPL_MAX_SIZE=0x1a000 -CONFIG_SPL_PAD_TO=0x20000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x80100000 -CONFIG_SPL_BSS_MAX_SIZE=0x80000 -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_BOARD_INIT=y -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SYS_SPL_MALLOC=y -CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y -CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x80200000 -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xf0 -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C=y -CONFIG_SPL_MPC8XXX_INIT_DDR=y -CONFIG_SPL_NAND_SUPPORT=y -CONFIG_SPL_WATCHDOG=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_IMLS=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_DM=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_SPL_EFI_PARTITION is not set -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_NAND=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_USE_ETHPRIME=y -CONFIG_ETHPRIME="FM1@DTSEC3" -CONFIG_FSL_CAAM=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_SPL_SYS_I2C_LEGACY=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x53 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y -CONFIG_SYS_NAND_U_BOOT_OFFS=0x20000 -CONFIG_SF_DEFAULT_BUS=1 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHY_AQUANTIA=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_DM_MDIO=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_SYS_FMAN_FW_ADDR=0x900000 -CONFIG_NVME_PCI=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_SYS_QE_FMAN_FW_IN_NAND=y -CONFIG_DM_SERIAL=y -CONFIG_SPL_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y -# CONFIG_SPL_USE_TINY_PRINTF is not set -CONFIG_EFI_LOADER_BOUNCE_BUFFER=y diff --git a/configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig b/configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig deleted file mode 100644 index fe0dd04f1f90..000000000000 --- a/configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig +++ /dev/null @@ -1,124 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043ARDB=y -CONFIG_TEXT_BASE=0x82000000 -CONFIG_SYS_MALLOC_LEN=0x102000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb" -CONFIG_SPL_TEXT_BASE=0x10000000 -CONFIG_FSL_LS_PPA=y -CONFIG_SYS_MONITOR_LEN=1064960 -CONFIG_SPL_MMC=y -CONFIG_SPL_SERIAL=y -CONFIG_SPL_DRIVERS_MISC=y -CONFIG_SPL_STACK=0x1001e000 -CONFIG_SPL=y -CONFIG_PCI=y -CONFIG_OF_BOARD_FIXUP=y -CONFIG_NXP_ESBC=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_RAMBOOT_PBL=y -CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043ardb/ls1043ardb_pbi.cfg" -CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043ardb/ls1043ardb_rcw_sd.cfg" -CONFIG_DISTRO_DEFAULTS=y -CONFIG_SD_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -CONFIG_BOOTCOMMAND="run distro_bootcmd; run sd_bootcmd; env exists secureboot && esbc_halt;" -CONFIG_MISC_INIT_R=y -CONFIG_SPL_MAX_SIZE=0x17000 -CONFIG_SPL_PAD_TO=0x1d000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x8f000000 -CONFIG_SPL_BSS_MAX_SIZE=0x80000 -CONFIG_SPL_FSL_PBL=y -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SYS_SPL_MALLOC=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x110 -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR=y -CONFIG_SPL_WATCHDOG=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_IMLS=y -CONFIG_CMD_SPL=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_DM=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_SPL_EFI_PARTITION is not set -CONFIG_OF_CONTROL=y -CONFIG_SPL_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_USE_ETHPRIME=y -CONFIG_ETHPRIME="FM1@DTSEC3" -CONFIG_SPL_DM=y -# CONFIG_SPL_BLK is not set -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_FSL_SEC_MON_BE=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x53 -# CONFIG_SPL_DM_MMC is not set -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SF_DEFAULT_BUS=1 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_DM_MDIO=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_SYS_FMAN_FW_ADDR=0x900000 -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_SYS_QE_FW_ADDR=0x940000 -CONFIG_SYS_QE_FMAN_FW_IN_MMC=y -CONFIG_SPECIFY_CONSOLE_INDEX=y -CONFIG_DM_SERIAL=y -CONFIG_SYS_NS16550=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y -# CONFIG_SPL_USE_TINY_PRINTF is not set -CONFIG_RSA=y -CONFIG_SPL_RSA=y -CONFIG_EFI_LOADER_BOUNCE_BUFFER=y diff --git a/configs/ls1043ardb_sdcard_defconfig b/configs/ls1043ardb_sdcard_defconfig deleted file mode 100644 index aa5404cbb50e..000000000000 --- a/configs/ls1043ardb_sdcard_defconfig +++ /dev/null @@ -1,126 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_TARGET_LS1043ARDB=y -CONFIG_TEXT_BASE=0x82000000 -CONFIG_SYS_MALLOC_LEN=0x102000 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1000fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_OFFSET=0x300000 -CONFIG_SYS_I2C_MXC_I2C1=y -CONFIG_SYS_I2C_MXC_I2C2=y -CONFIG_SYS_I2C_MXC_I2C3=y -CONFIG_SYS_I2C_MXC_I2C4=y -CONFIG_DM_GPIO=y -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls1043a-rdb" -CONFIG_SPL_TEXT_BASE=0x10000000 -CONFIG_FSL_LS_PPA=y -CONFIG_SYS_MONITOR_LEN=1048576 -CONFIG_SPL_MMC=y -CONFIG_SPL_SERIAL=y -CONFIG_SPL_DRIVERS_MISC=y -CONFIG_SPL_STACK=0x1001e000 -CONFIG_SPL=y -CONFIG_PCI=y -CONFIG_OF_BOARD_FIXUP=y -CONFIG_LAYERSCAPE_NS_ACCESS=y -CONFIG_PCIE1=y -CONFIG_PCIE2=y -CONFIG_PCIE3=y -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_RAMBOOT_PBL=y -CONFIG_SYS_FSL_PBL_PBI="board/freescale/ls1043ardb/ls1043ardb_pbi.cfg" -CONFIG_SYS_FSL_PBL_RCW="board/freescale/ls1043ardb/ls1043ardb_rcw_sd.cfg" -CONFIG_DISTRO_DEFAULTS=y -CONFIG_SD_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -CONFIG_BOOTCOMMAND="run distro_bootcmd; run sd_bootcmd; env exists secureboot && esbc_halt;" -CONFIG_ARCH_MISC_INIT=y -CONFIG_MISC_INIT_R=y -CONFIG_SPL_MAX_SIZE=0x17000 -CONFIG_SPL_PAD_TO=0x1d000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x8f000000 -CONFIG_SPL_BSS_MAX_SIZE=0x80000 -CONFIG_SPL_FSL_PBL=y -CONFIG_SPL_BOARD_INIT=y -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SYS_SPL_MALLOC=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0xf0 -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_MPC8XXX_INIT_DDR=y -CONFIG_SPL_WATCHDOG=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_IMLS=y -CONFIG_CMD_SPL=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_DM=y -CONFIG_CMD_GPIO=y -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_USB=y -CONFIG_CMD_CACHE=y -CONFIG_MTDPARTS_DEFAULT="mtdparts=60000000.nor:2m@0x100000(nor_bank0_uboot),40m@0x1100000(nor_bank0_fit),7m(nor_bank0_user),2m@0x4100000(nor_bank4_uboot),40m@0x5100000(nor_bank4_fit),-(nor_bank4_user);7e800000.flash:1m(nand_uboot),1m(nand_uboot_env),20m(nand_fit);spi0.0:1m(uboot),5m(kernel),1m(dtb),9m(file_system)" -# CONFIG_SPL_EFI_PARTITION is not set -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_MMC=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_USE_ETHPRIME=y -CONFIG_ETHPRIME="FM1@DTSEC3" -CONFIG_FSL_CAAM=y -CONFIG_MPC8XXX_GPIO=y -CONFIG_DM_I2C=y -CONFIG_SPL_SYS_I2C_LEGACY=y -CONFIG_I2C_SET_DEFAULT_BUS_NUM=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x53 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SF_DEFAULT_BUS=1 -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHY_AQUANTIA=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_VITESSE=y -CONFIG_DM_MDIO=y -CONFIG_E1000=y -CONFIG_FMAN_ENET=y -CONFIG_SYS_FMAN_FW_ADDR=0x900000 -CONFIG_NVME_PCI=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_SYS_QE_FW_ADDR=0x940000 -CONFIG_SYS_QE_FMAN_FW_IN_MMC=y -CONFIG_DM_SERIAL=y -CONFIG_SPL_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y -# CONFIG_SPL_USE_TINY_PRINTF is not set -CONFIG_EFI_LOADER_BOUNCE_BUFFER=y diff --git a/configs/ls2080aqds_SECURE_BOOT_defconfig b/configs/ls2080aqds_SECURE_BOOT_defconfig deleted file mode 100644 index d8416265cfb3..000000000000 --- a/configs/ls2080aqds_SECURE_BOOT_defconfig +++ /dev/null @@ -1,108 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_GIC_V3_ITS=y -CONFIG_TARGET_LS2080AQDS=y -CONFIG_TEXT_BASE=0x30100000 -CONFIG_SYS_MALLOC_LEN=0x202000 -CONFIG_NR_DRAM_BANKS=3 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-qds" -CONFIG_FSL_LS_PPA=y -CONFIG_SYS_MONITOR_LEN=1048576 -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_NXP_ESBC=y -CONFIG_FSL_USE_PCA9547_MUX=y -CONFIG_FSL_QIXIS=y -# CONFIG_QIXIS_I2C_ACCESS is not set -# CONFIG_SYS_MALLOC_F is not set -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_DYNAMIC_SYS_CLK_FREQ=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256" -CONFIG_BOOTCOMMAND="fsl_mc apply dpl 0x580d00000 && cp.b $kernel_start $kernel_load $kernel_size && bootm $kernel_load" -CONFIG_RESET_PHY_R=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_EEPROM=y -CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3 -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_PCI=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y -# CONFIG_ISO_PARTITION is not set -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_USE_ETHPRIME=y -CONFIG_ETHPRIME="DPMAC1@xgmii" -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_DYNAMIC_DDR_CLK_FREQ=y -CONFIG_DIMM_SLOTS_PER_CTLR=2 -CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS=2 -CONFIG_DDR_ECC=y -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_SYS_FSL_DDR_INTLV_256B=y -CONFIG_SYS_I2C_LEGACY=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -CONFIG_ESDHC_DETECT_QUIRK=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_SYS_MAX_FLASH_BANKS=2 -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SYS_NAND_MAX_OOBFREE=2 -CONFIG_SYS_NAND_MAX_ECCPOS=256 -CONFIG_DM_SPI_FLASH=y -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_FSL_MEMAC=y -CONFIG_SYS_MEMAC_LITTLE_ENDIAN=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_MII=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_RTC_ENABLE_32KHZ_OUTPUT=y -CONFIG_RTC_DS3231=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_DSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y -CONFIG_RSA=y -CONFIG_RSA_SOFTWARE_EXP=y diff --git a/configs/ls2080aqds_defconfig b/configs/ls2080aqds_defconfig deleted file mode 100644 index be08d5ba86a8..000000000000 --- a/configs/ls2080aqds_defconfig +++ /dev/null @@ -1,109 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_GIC_V3_ITS=y -CONFIG_TARGET_LS2080AQDS=y -CONFIG_TEXT_BASE=0x30100000 -CONFIG_SYS_MALLOC_LEN=0x202000 -CONFIG_NR_DRAM_BANKS=3 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-qds" -CONFIG_FSL_LS_PPA=y -CONFIG_SYS_MONITOR_LEN=1048576 -CONFIG_ENV_ADDR=0x80300000 -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_FSL_USE_PCA9547_MUX=y -CONFIG_FSL_QIXIS=y -# CONFIG_QIXIS_I2C_ACCESS is not set -# CONFIG_SYS_MALLOC_F is not set -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_DYNAMIC_SYS_CLK_FREQ=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256" -CONFIG_BOOTCOMMAND="fsl_mc apply dpl 0x580d00000 && cp.b $kernel_start $kernel_load $kernel_size && bootm $kernel_load" -CONFIG_RESET_PHY_R=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_EEPROM=y -CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3 -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_PCI=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y -# CONFIG_ISO_PARTITION is not set -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_USE_ETHPRIME=y -CONFIG_ETHPRIME="DPMAC1@xgmii" -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_FSL_CAAM=y -CONFIG_DYNAMIC_DDR_CLK_FREQ=y -CONFIG_DIMM_SLOTS_PER_CTLR=2 -CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS=2 -CONFIG_DDR_ECC=y -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_SYS_FSL_DDR_INTLV_256B=y -CONFIG_SYS_I2C_LEGACY=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -CONFIG_ESDHC_DETECT_QUIRK=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_SYS_MAX_FLASH_BANKS=2 -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SYS_NAND_MAX_OOBFREE=2 -CONFIG_SYS_NAND_MAX_ECCPOS=256 -CONFIG_DM_SPI_FLASH=y -CONFIG_SPI_FLASH_EON=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_SPI_FLASH_SST=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_FSL_MEMAC=y -CONFIG_SYS_MEMAC_LITTLE_ENDIAN=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_MII=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_RTC_ENABLE_32KHZ_OUTPUT=y -CONFIG_RTC_DS3231=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_DSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls2080aqds_sdcard_defconfig b/configs/ls2080aqds_sdcard_defconfig deleted file mode 100644 index b45819f87b3e..000000000000 --- a/configs/ls2080aqds_sdcard_defconfig +++ /dev/null @@ -1,116 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_GIC_V3_ITS=y -CONFIG_TARGET_LS2080AQDS=y -CONFIG_TEXT_BASE=0x80400000 -CONFIG_SYS_MALLOC_LEN=0x0220000 -CONFIG_SYS_MALLOC_F_LEN=0x400 -CONFIG_SPL_LIBCOMMON_SUPPORT=y -CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=3 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 -CONFIG_ENV_SIZE=0x20000 -CONFIG_ENV_OFFSET=0x300000 -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-qds" -CONFIG_SPL_TEXT_BASE=0x1800a000 -CONFIG_FSL_LS_PPA=y -CONFIG_SYS_MONITOR_LEN=1048576 -CONFIG_SPL_MMC=y -CONFIG_SPL_SERIAL=y -CONFIG_SPL_DRIVERS_MISC=y -CONFIG_SPL_STACK=0x18009ff0 -CONFIG_SPL=y -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_FSL_USE_PCA9547_MUX=y -CONFIG_FSL_QIXIS=y -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_DYNAMIC_SYS_CLK_FREQ=y -CONFIG_SD_BOOT=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256" -CONFIG_BOOTCOMMAND="mmc read 0x80200000 0x6800 0x800; fsl_mc apply dpl 0x80200000 && mmc read $kernel_load $kernel_start $kernel_size && bootm $kernel_load" -CONFIG_RESET_PHY_R=y -CONFIG_SPL_MAX_SIZE=0x16000 -CONFIG_SPL_HAS_BSS_LINKER_SECTION=y -CONFIG_SPL_BSS_START_ADDR=0x80100000 -CONFIG_SPL_BSS_MAX_SIZE=0x100000 -# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set -CONFIG_SYS_SPL_MALLOC=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y -CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x8b0 -CONFIG_SPL_ENV_SUPPORT=y -CONFIG_SPL_I2C=y -CONFIG_SPL_MPC8XXX_INIT_DDR=y -CONFIG_SPL_TARGET="u-boot-with-spl.bin" -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_GREPENV=y -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_PCI=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y -CONFIG_OF_CONTROL=y -CONFIG_OF_EMBED=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_MMC=y -CONFIG_SYS_RELOC_GD_ENV_ADDR=y -CONFIG_USE_ETHPRIME=y -CONFIG_ETHPRIME="DPMAC1@xgmii" -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_DYNAMIC_DDR_CLK_FREQ=y -CONFIG_DIMM_SLOTS_PER_CTLR=2 -CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS=2 -CONFIG_DDR_ECC=y -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_SYS_FSL_DDR_INTLV_256B=y -CONFIG_SYS_I2C_LEGACY=y -CONFIG_SYS_I2C_EARLY_INIT=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -CONFIG_ESDHC_DETECT_QUIRK=y -CONFIG_MTD=y -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SYS_NAND_MAX_OOBFREE=2 -CONFIG_SYS_NAND_MAX_ECCPOS=256 -CONFIG_DM_SPI_FLASH=y -# CONFIG_SPI_FLASH_BAR is not set -CONFIG_SPI_FLASH_SPANSION=y -CONFIG_PHYLIB=y -CONFIG_PHYLIB_10G=y -CONFIG_PHY_REALTEK=y -CONFIG_PHY_TERANETICS=y -CONFIG_PHY_VITESSE=y -CONFIG_FSL_MEMAC=y -CONFIG_SYS_MEMAC_LITTLE_ENDIAN=y -CONFIG_PHY_GIGE=y -CONFIG_E1000=y -CONFIG_MII=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_RTC_ENABLE_32KHZ_OUTPUT=y -CONFIG_RTC_DS3231=y -CONFIG_DM_SCSI=y -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_QSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y diff --git a/configs/ls2080ardb_SECURE_BOOT_defconfig b/configs/ls2080ardb_SECURE_BOOT_defconfig deleted file mode 100644 index bcd83018112c..000000000000 --- a/configs/ls2080ardb_SECURE_BOOT_defconfig +++ /dev/null @@ -1,106 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_GIC_V3_ITS=y -CONFIG_TARGET_LS2080ARDB=y -CONFIG_TEXT_BASE=0x30100000 -CONFIG_SYS_MALLOC_LEN=0x202000 -CONFIG_NR_DRAM_BANKS=3 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-rdb" -CONFIG_FSL_LS_PPA=y -CONFIG_SYS_MONITOR_LEN=1048576 -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_NXP_ESBC=y -CONFIG_FSL_USE_PCA9547_MUX=y -CONFIG_VID=y -CONFIG_VID_FLS_ENV="ls2080ardb_vdd_mv" -CONFIG_VOL_MONITOR_IR36021_READ=y -CONFIG_VOL_MONITOR_IR36021_SET=y -CONFIG_FSL_QIXIS=y -# CONFIG_QIXIS_I2C_ACCESS is not set -# CONFIG_SYS_MALLOC_F is not set -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_DYNAMIC_SYS_CLK_FREQ=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS1,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256" -CONFIG_BOOTCOMMAND="env exists mcinitcmd && env exists secureboot && esbc_validate 0x5806C0000; env exists mcinitcmd && fsl_mc lazyapply dpl 0x580d00000;run distro_bootcmd;run nor_bootcmd; env exists secureboot && esbc_halt;" -CONFIG_MISC_INIT_R=y -CONFIG_RESET_PHY_R=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_EEPROM=y -CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3 -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_PCI=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_USE_ETHPRIME=y -CONFIG_ETHPRIME="DPMAC1@xgmii" -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_DDR_CLK_FREQ=133333333 -CONFIG_DIMM_SLOTS_PER_CTLR=2 -CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS=2 -CONFIG_DDR_ECC=y -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_SYS_FSL_DDR_INTLV_256B=y -CONFIG_SYS_I2C_LEGACY=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SYS_NAND_MAX_OOBFREE=2 -CONFIG_SYS_NAND_MAX_ECCPOS=256 -CONFIG_DM_SPI_FLASH=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_PHYLIB=y -CONFIG_PHY_AQUANTIA=y -CONFIG_PHY_CORTINA=y -CONFIG_CORTINA_FW_ADDR=0x580980000 -CONFIG_FSL_MEMAC=y -CONFIG_SYS_MEMAC_LITTLE_ENDIAN=y -CONFIG_E1000=y -CONFIG_MII=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_RTC_DS3231=y -CONFIG_DM_SCSI=y -CONFIG_CONS_INDEX=2 -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_DSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y -CONFIG_RSA=y -CONFIG_RSA_SOFTWARE_EXP=y diff --git a/configs/ls2080ardb_defconfig b/configs/ls2080ardb_defconfig deleted file mode 100644 index 38ec438c3bca..000000000000 --- a/configs/ls2080ardb_defconfig +++ /dev/null @@ -1,107 +0,0 @@ -CONFIG_ARM=y -CONFIG_COUNTER_FREQUENCY=25000000 -CONFIG_GIC_V3_ITS=y -CONFIG_TARGET_LS2080ARDB=y -CONFIG_TEXT_BASE=0x30100000 -CONFIG_SYS_MALLOC_LEN=0x202000 -CONFIG_NR_DRAM_BANKS=3 -CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y -CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x1800fff0 -CONFIG_ENV_SIZE=0x2000 -CONFIG_ENV_SECT_SIZE=0x20000 -CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-rdb" -CONFIG_FSL_LS_PPA=y -CONFIG_SYS_MONITOR_LEN=1048576 -CONFIG_ENV_ADDR=0x80300000 -CONFIG_PCI=y -CONFIG_AHCI=y -CONFIG_FSL_USE_PCA9547_MUX=y -CONFIG_VID=y -CONFIG_VID_FLS_ENV="ls2080ardb_vdd_mv" -CONFIG_VOL_MONITOR_IR36021_READ=y -CONFIG_VOL_MONITOR_IR36021_SET=y -CONFIG_FSL_QIXIS=y -# CONFIG_QIXIS_I2C_ACCESS is not set -# CONFIG_SYS_MALLOC_F is not set -CONFIG_REMAKE_ELF=y -CONFIG_MP=y -CONFIG_FIT_VERBOSE=y -CONFIG_OF_BOARD_SETUP=y -CONFIG_OF_STDOUT_VIA_ALIAS=y -CONFIG_DYNAMIC_SYS_CLK_FREQ=y -CONFIG_BOOTDELAY=10 -CONFIG_USE_BOOTARGS=y -CONFIG_BOOTARGS="console=ttyS1,115200 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 ramdisk_size=0x2000000 default_hugepagesz=2m hugepagesz=2m hugepages=256" -CONFIG_BOOTCOMMAND="env exists mcinitcmd && env exists secureboot && esbc_validate 0x5806C0000; env exists mcinitcmd && fsl_mc lazyapply dpl 0x580d00000;run distro_bootcmd;run nor_bootcmd; env exists secureboot && esbc_halt;" -CONFIG_MISC_INIT_R=y -CONFIG_RESET_PHY_R=y -CONFIG_SYS_MAXARGS=64 -CONFIG_SYS_PBSIZE=532 -CONFIG_CMD_IMLS=y -CONFIG_CMD_GREPENV=y -CONFIG_CMD_EEPROM=y -CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=3 -CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 -CONFIG_CMD_GPT=y -CONFIG_CMD_I2C=y -CONFIG_CMD_MMC=y -CONFIG_CMD_NAND=y -CONFIG_CMD_PCI=y -CONFIG_CMD_USB=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_CACHE=y -CONFIG_CMD_DATE=y -CONFIG_OF_CONTROL=y -CONFIG_ENV_OVERWRITE=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_USE_ETHPRIME=y -CONFIG_ETHPRIME="DPMAC1@xgmii" -CONFIG_NET_RANDOM_ETHADDR=y -CONFIG_SATA=y -CONFIG_SATA_CEVA=y -CONFIG_FSL_CAAM=y -CONFIG_DDR_CLK_FREQ=133333333 -CONFIG_DIMM_SLOTS_PER_CTLR=2 -CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS=2 -CONFIG_DDR_ECC=y -CONFIG_ECC_INIT_VIA_DDRCONTROLLER=y -CONFIG_SYS_FSL_DDR_INTLV_256B=y -CONFIG_SYS_I2C_LEGACY=y -CONFIG_SYS_I2C_EEPROM_ADDR=0x57 -CONFIG_FSL_ESDHC=y -CONFIG_MTD=y -CONFIG_MTD_NOR_FLASH=y -CONFIG_FLASH_CFI_DRIVER=y -CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y -CONFIG_SYS_FLASH_EMPTY_INFO=y -CONFIG_SYS_FLASH_CFI=y -CONFIG_SYS_FLASH_QUIET_TEST=y -CONFIG_SYS_MAX_FLASH_SECT=1024 -CONFIG_MTD_RAW_NAND=y -CONFIG_NAND_FSL_IFC=y -CONFIG_SYS_NAND_ONFI_DETECTION=y -CONFIG_SYS_NAND_MAX_OOBFREE=2 -CONFIG_SYS_NAND_MAX_ECCPOS=256 -CONFIG_DM_SPI_FLASH=y -CONFIG_SPI_FLASH_STMICRO=y -CONFIG_PHYLIB=y -CONFIG_PHY_AQUANTIA=y -CONFIG_PHY_CORTINA=y -CONFIG_CORTINA_FW_ADDR=0x580980000 -CONFIG_FSL_MEMAC=y -CONFIG_SYS_MEMAC_LITTLE_ENDIAN=y -CONFIG_E1000=y -CONFIG_MII=y -CONFIG_NVME_PCI=y -CONFIG_DM_PCI_COMPAT=y -CONFIG_PCIE_LAYERSCAPE_RC=y -CONFIG_RTC_DS3231=y -CONFIG_DM_SCSI=y -CONFIG_CONS_INDEX=2 -CONFIG_SYS_NS16550_SERIAL=y -CONFIG_SPI=y -CONFIG_DM_SPI=y -CONFIG_FSL_DSPI=y -CONFIG_USB=y -CONFIG_USB_XHCI_HCD=y -CONFIG_USB_XHCI_DWC3=y -- 2.17.1
