Hi,
On 19/12/2023 12:11, MD Danish Anwar wrote:
> Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI
> AM654 SR2.0.
>
> The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces
> support for ICSSG driver in uboot. This series also adds the driver's
> dependencies.
>
> The ICSSG2 node is added in device tree overlay so that it remains in
> sync with linux kernel.
>
> The series introduces device tree and config changes and AM65x
> to enable ICSSG driver. The series also enables SPL_LOAD_FIT_APPLY_OVERLAY
> for AM65x in order to load overlay over spl.
>
> This series has been tested on AM65x SR2.0, and the ICSSG interface is
> able to ping / dhcp and boot kernel using tftp in uboot.
>
> To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC
> cores and RPROC cores need to be booted with the firmware. This step is
> done inside driver in kernel as kernel supports APIs like
> rproc_set_firmware() and rproc_fw_boot(). But as u-boot doesn't have these
> APIs, the same needs to be done via u-boot cmds.
>
> To make sure icssg-eth works we need to do below steps.
>
> 1. Initialize rproc cores i.e. rproc_init()
> 2. Load $firmware_file from partition '1:2' (root) on device (mmc in this
> example)
> 3. Load the firmware file to rproc cores passing. i.e. rproc_load()
> taking rproc_id, loadaddr and file size as arguments.
> 4. Start rproc cores. i.e. rproc_start() taking rproc_id as arguments
>
> The above steps are done by running the below commands at u-boot prompt.
>
> => setenv start_icssg2 'rproc start 14; rproc start 15; rproc start 16; rproc
> start 17; rproc start 18; rproc start 19'
> => setenv stop_icssg2 'rproc stop 14; rproc stop 15; rproc stop 16; rproc
> stop 17; rproc stop 18; rproc stop 19'
> => setenv firmware_dir '/lib/firmware/ti-pruss'
> => setenv get_firmware_mmc 'load mmc ${bootpart} ${loadaddr}
> ${firmware_dir}/${firmware_file}'
>
> => setenv init_icssg2 'setenv ethact icssg2-eth; setenv autoload no; rproc
> init; setenv loadaddr 0x80000000; \
> setenv firmware_file am65x-sr2-pru0-prueth-fw.elf; run get_firmware_mmc;
> rproc load 14 0x80000000 ${filesize}; \
> setenv loadaddr 0x89000000; setenv firmware_file
> am65x-sr2-rtu0-prueth-fw.elf; run get_firmware_mmc; rproc load 15 0x89000000
> ${filesize}; \
> setenv loadaddr 0x90000000; setenv firmware_file
> am65x-sr2-txpru0-prueth-fw.elf; run get_firmware_mmc; rproc load 16
> 0x90000000 ${filesize}; \
> setenv loadaddr 0x80000000; setenv firmware_file
> am65x-sr2-pru1-prueth-fw.elf; run get_firmware_mmc; rproc load 17 0x80000000
> ${filesize}; \
> setenv loadaddr 0x89000000; setenv firmware_file
> am65x-sr2-rtu1-prueth-fw.elf; run get_firmware_mmc; rproc load 18 0x89000000
> ${filesize}; \
> setenv loadaddr 0x90000000; setenv firmware_file
> am65x-sr2-txpru1-prueth-fw.elf; run get_firmware_mmc; rproc load 19
> 0x90000000 ${filesize}; \
> run start_icssg2;'
A whole bunch of commands are required to get ethernet functional.
This is not at all user friendly and will be a maintenance nightmare.
What worries me is tracking the 6 different rproc cores and the 6 different
firmware files to start 1 ethernet device.
This will get even more interesting when we have to deal with different ICSSG
instances on different boards.
What is preventing the driver from starting the rproc cores it needs so user
doesn't need to care about it?
All the necessary information is in the Device tree. At least this is how it is
done on Linux.
>
> => run init_icssg2
> => dhcp
> k3-navss-ringacc ringacc@3c000000: Ring Accelerator probed rings:818,
> gp-rings[304,100] sci-dev-id:187
> k3-navss-ringacc ringacc@3c000000: dma-ring-reset-quirk: disabled
> prueth icssg2-eth: K3 ICSSG: rflow_id_base: 8, chn_name = rx0
> link up on port 0, speed 1000, full duplex
> BOOTP broadcast 1
> BOOTP broadcast 2
> BOOTP broadcast 3
> DHCP client bound to address 192.168.4.58 (1020 ms)
>
What about shutting down the interface?
I believe this has to be done manually too?
> Thanks and Regards,
> MD Danish Anwar
>
> MD Danish Anwar (16):
> net: ti: icssg: Add Firmware Interface for ICSSG Ethernet driver.
> net: ti: icssg: Add Firmware config and classification APIs.
> net: ti: icssg: Add icssg queues APIs and macros
> net: ti: icssg: Add ICSSG ethernet driver
> net: ti: icssg: Add support sending FDB command to update rx_flow_id
> net: ti: icssg: Enforce pinctrl state on the MDIO child node
> arm: dts: k3-am65: Add additional regs for DMA components
> arm: dts: k3-am65: Add cfg reg region to ringacc node
> arm: dts: k3-am65-main: Add ICSSG IEP nodes
> arm: dts: k3-am654-base-board: Add ICSSG2 Ethernet support
> arm: dts: k3-am65x-binman: Add ICSSG2 overlay and configuration
> configs: am65x_evm_a53: Enable ICSSG Driver
> configs: am65x_evm_a53_defconfig: add SPL_LOAD_FIT_APPLY_OVERLAY
> tools/fdtgrep: Include __symbols__ table
> board: ti: am65x: Add check for k3-am654-icssg2 in
> board_fit_config_match()
> Revert "dm: core: Report bootph-pre-ram/sram node as pre-reloc after
> relocation"
>
> arch/arm/dts/Makefile | 3 +-
> arch/arm/dts/k3-am65-main.dtsi | 49 ++-
> arch/arm/dts/k3-am65-mcu.dtsi | 13 +-
> arch/arm/dts/k3-am654-icssg2.dtso | 145 +++++++
> arch/arm/dts/k3-am65x-binman.dtsi | 85 ++++
> board/ti/am65x/evm.c | 11 +-
> configs/am65x_evm_a53_defconfig | 4 +
> drivers/core/ofnode.c | 2 +-
> drivers/net/ti/Kconfig | 9 +
> drivers/net/ti/Makefile | 1 +
> drivers/net/ti/icss_mii_rt.h | 192 +++++++++
> drivers/net/ti/icssg_classifier.c | 376 +++++++++++++++++
> drivers/net/ti/icssg_config.c | 469 +++++++++++++++++++++
> drivers/net/ti/icssg_config.h | 195 +++++++++
> drivers/net/ti/icssg_prueth.c | 654 ++++++++++++++++++++++++++++++
> drivers/net/ti/icssg_prueth.h | 89 ++++
> drivers/net/ti/icssg_queues.c | 51 +++
> drivers/net/ti/icssg_switch_map.h | 209 ++++++++++
> include/dm/ofnode.h | 8 +-
> tools/fdtgrep.c | 8 +
> 20 files changed, 2555 insertions(+), 18 deletions(-)
> create mode 100644 arch/arm/dts/k3-am654-icssg2.dtso
> create mode 100644 drivers/net/ti/icss_mii_rt.h
> create mode 100644 drivers/net/ti/icssg_classifier.c
> create mode 100644 drivers/net/ti/icssg_config.c
> create mode 100644 drivers/net/ti/icssg_config.h
> create mode 100644 drivers/net/ti/icssg_prueth.c
> create mode 100644 drivers/net/ti/icssg_prueth.h
> create mode 100644 drivers/net/ti/icssg_queues.c
> create mode 100644 drivers/net/ti/icssg_switch_map.h
>
> base:commit: a6f86132e30a407c7f96461df53c62fbe52e2b54
--
cheers,
-roger
