Remove bootph properties no longer needed. These are now handled in upstream Linux device trees.
Signed-off-by: Wadim Egorov <[email protected]> --- .../k3-am625-phyboard-lyra-rdk-u-boot.dtsi | 100 ------------------ arch/arm/dts/k3-am625-r5-phycore-som-2gb.dts | 8 -- 2 files changed, 108 deletions(-) diff --git a/arch/arm/dts/k3-am625-phyboard-lyra-rdk-u-boot.dtsi b/arch/arm/dts/k3-am625-phyboard-lyra-rdk-u-boot.dtsi index 3a1a8b06dc6..daa1710dbc4 100644 --- a/arch/arm/dts/k3-am625-phyboard-lyra-rdk-u-boot.dtsi +++ b/arch/arm/dts/k3-am625-phyboard-lyra-rdk-u-boot.dtsi @@ -19,36 +19,16 @@ mmc0 = &sdhci0; mmc1 = &sdhci1; }; - - memory@80000000 { - bootph-all; - }; -}; - -&cpsw3g { - bootph-all; -}; - -&cpsw_port1 { - bootph-all; }; &cpsw_port2 { status = "disabled"; }; -&cpsw3g_phy1 { - bootph-all; -}; - &phy_gmii_sel { bootph-all; }; -&fss { - bootph-all; -}; - &main_bcdma { bootph-all; reg = <0x00 0x485c0100 0x00 0x100>, @@ -63,38 +43,6 @@ "ringrt" , "cfg", "tchan", "rchan"; }; -&main_gpio0 { - bootph-all; -}; - -&main_mdio1_pins_default { - bootph-all; -}; - -&main_i2c0 { - bootph-all; -}; - -&main_i2c0_pins_default { - bootph-all; -}; - -&main_mmc0_pins_default { - bootph-all; -}; - -&main_mmc1_pins_default { - bootph-all; -}; - -&main_pktdma { - bootph-all; -}; - -&main_rgmii1_pins_default { - bootph-all; -}; - &main_rti1 { status = "disabled"; }; @@ -111,27 +59,8 @@ status = "disabled"; }; -&main_uart0 { - bootph-all; -}; - -&main_uart0_pins_default { - bootph-all; -}; - -&main_uart1 { - bootph-all; -}; - -&main_uart1_pins_default { - bootph-all; -}; - &ospi0 { - bootph-all; - flash@0 { - bootph-all; partitions { compatible = "fixed-partitions"; #address-cells = <1>; @@ -161,43 +90,14 @@ }; }; -&ospi0_pins_default { - bootph-all; -}; - -&sdhci0 { - bootph-all; -}; - -&sdhci1 { - bootph-all; -}; - -&usbss0 { - bootph-all; -}; - &usb0 { dr_mode = "peripheral"; - bootph-all; }; &usb0_phy_ctrl { bootph-all; }; -&vcc_3v3_mmc { - bootph-all; -}; - -&vcc_5v0_som { - bootph-all; -}; - -&vddshv5_sdio { - bootph-all; -}; - &wkup_uart0 { bootph-all; }; diff --git a/arch/arm/dts/k3-am625-r5-phycore-som-2gb.dts b/arch/arm/dts/k3-am625-r5-phycore-som-2gb.dts index 03dc81a4afa..0f2c592593e 100644 --- a/arch/arm/dts/k3-am625-r5-phycore-som-2gb.dts +++ b/arch/arm/dts/k3-am625-r5-phycore-som-2gb.dts @@ -93,14 +93,6 @@ ti,sci = <&dm_tifs>; }; -/* Main UART1 is used for TIFS firmware logs */ -&main_uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&main_uart1_pins_default>; - status = "okay"; - bootph-pre-ram; -}; - &mcu_pmx0 { wkup_uart0_pins_default: wkup-uart0-pins-default { pinctrl-single,pins = < -- 2.48.1
