Add the Allied Telesis x220 board. There are a number of other variants with the same CPU block that are sold under some different brand names but the x220 was first.
The x220 uses the AlleyCat3 switch chip with integrated ARMv7 CPU. Because of this it is reliant on a binary blob for the DDR training. In upstream u-boot this is replaced by an empty file. Signed-off-by: Chris Packham <[email protected]> --- Notes: Changes in v2: - None arch/arm/dts/Makefile | 1 + arch/arm/dts/armada-xp-atl-x220.dts | 162 +++++++++++++++++++++++ arch/arm/mach-mvebu/Kconfig | 7 + board/alliedtelesis/x220/.gitattributes | 1 + board/alliedtelesis/x220/.gitignore | 1 + board/alliedtelesis/x220/MAINTAINERS | 7 + board/alliedtelesis/x220/Makefile | 14 ++ board/alliedtelesis/x220/README | 4 + board/alliedtelesis/x220/binary.0 | Bin 0 -> 423 bytes board/alliedtelesis/x220/kwbimage.cfg.in | 12 ++ board/alliedtelesis/x220/x220.c | 67 ++++++++++ configs/x220_defconfig | 76 +++++++++++ include/configs/x220.h | 20 +++ 13 files changed, 372 insertions(+) create mode 100644 arch/arm/dts/armada-xp-atl-x220.dts create mode 100644 board/alliedtelesis/x220/.gitattributes create mode 100644 board/alliedtelesis/x220/.gitignore create mode 100644 board/alliedtelesis/x220/MAINTAINERS create mode 100644 board/alliedtelesis/x220/Makefile create mode 100644 board/alliedtelesis/x220/README create mode 100644 board/alliedtelesis/x220/binary.0 create mode 100644 board/alliedtelesis/x220/kwbimage.cfg.in create mode 100644 board/alliedtelesis/x220/x220.c create mode 100644 configs/x220_defconfig create mode 100644 include/configs/x220.h diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index fcad6fb2fc71..797d9a61154c 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -155,6 +155,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += \ armada-388-gp.dtb \ armada-388-helios4.dtb \ armada-38x-controlcenterdc.dtb \ + armada-xp-atl-x220.dtb \ armada-xp-crs305-1g-4s.dtb \ armada-xp-crs305-1g-4s-bit.dtb \ armada-xp-crs326-24g-2s.dtb \ diff --git a/arch/arm/dts/armada-xp-atl-x220.dts b/arch/arm/dts/armada-xp-atl-x220.dts new file mode 100644 index 000000000000..5b3307ed2884 --- /dev/null +++ b/arch/arm/dts/armada-xp-atl-x220.dts @@ -0,0 +1,162 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Device Tree file for x220 board + * + * Copyright (C) 2025 Allied Telesis Labs + */ + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include "armada-xp-98dx3236.dtsi" +#include "mvebu-u-boot.dtsi" + +/ { + model = "x220"; + compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp-mv78260", + "marvell,armadaxp", "marvell,armada-370-xp"; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs = "console=ttyS0,115200"; + }; + + aliases { + i2c0 = &i2c0; + spi0 = &spi0; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x00000000 0x00000000 0x20000000>; + }; +}; + +&L2 { + arm,parity-enable; + marvell,ecc-enable; +}; + +&devbus_bootcs { + status = "okay"; + + /* Device Bus parameters are required */ + + /* Read parameters */ + devbus,bus-width = <16>; + devbus,turn-off-ps = <60000>; + devbus,badr-skew-ps = <0>; + devbus,acc-first-ps = <124000>; + devbus,acc-next-ps = <248000>; + devbus,rd-setup-ps = <0>; + devbus,rd-hold-ps = <0>; + + /* Write parameters */ + devbus,sync-enable = <0>; + devbus,wr-high-ps = <60000>; + devbus,wr-low-ps = <60000>; + devbus,ale-wr-ps = <60000>; +}; + +&uart0 { + status = "okay"; +}; + +&i2c0 { + clock-frequency = <100000>; + status = "okay"; + + rtc@68 { + compatible = "dallas,ds1340"; + reg = <0x68>; + }; + + adt7476a@2e { + compatible = "adi,adt7476"; + reg = <0x2e>; + }; + + sfpgpio: gpio@27 { + #address-cells = <2>; + #size-cells = <0>; + compatible = "nxp,pca9555"; + reg = <0x27>; + gpio-controller; + #gpio-cells = <2>; + }; + + systemgpio: gpio@25 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "nxp,pca9555"; + reg = <0x25>; + gpio-controller; + #gpio-cells = <2>; + + nand-protect { + gpio-hog; + gpios = <6 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "nand-protect"; + }; + + usb-enable { + gpio-hog; + gpios = <9 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb-enable"; + }; + + phy-reset { + gpio-hog; + gpios = <5 GPIO_ACTIVE_LOW>; + output-high; + line-name = "phy-reset"; + }; + + led-enable { + gpio-hog; + gpios = <13 GPIO_ACTIVE_HIGH>; + output-low; + line-name = "led-enable"; + }; + }; +}; + +&watchdog { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-flash", "jedec,spi-nor"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <20000000>; + }; +}; + +&nand_controller { + compatible = "marvell,armada370-nand-controller"; + label = "pxa3xx_nand-0"; + status = "okay"; + nand-rb = <0>; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; +}; + +&{/} { + boot-board { + compatible = "atl,boot-board"; + present-gpio = <&systemgpio 12 GPIO_ACTIVE_HIGH>; + override-gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; +}; + diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig index b76510ab4527..bc009163ed96 100644 --- a/arch/arm/mach-mvebu/Kconfig +++ b/arch/arm/mach-mvebu/Kconfig @@ -226,6 +226,10 @@ config TARGET_X240 select ALLEYCAT_5 imply BOOTSTD_DEFAULTS +config TARGET_X220 + bool "Support Allied Telesis x220" + select 98DX3336 + config TARGET_DB_XC3_24G4XG bool "Support DB-XC3-24G4XG" select 98DX3336 @@ -310,6 +314,7 @@ config SYS_BOARD default "x530" if TARGET_X530 default "x250" if TARGET_X250 default "x240" if TARGET_X240 + default "x220" if TARGET_X220 default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236 default "mvebu_alleycat-5" if TARGET_MVEBU_ALLEYCAT5 @@ -335,6 +340,7 @@ config SYS_CONFIG_NAME default "x530" if TARGET_X530 default "x250" if TARGET_X250 default "x240" if TARGET_X240 + default "x220" if TARGET_X220 default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236 default "mvebu_alleycat-5" if TARGET_MVEBU_ALLEYCAT5 @@ -360,6 +366,7 @@ config SYS_VENDOR default "alliedtelesis" if TARGET_X530 default "alliedtelesis" if TARGET_X250 default "alliedtelesis" if TARGET_X240 + default "alliedtelesis" if TARGET_X220 default "mikrotik" if TARGET_CRS3XX_98DX3236 default "Marvell" if TARGET_MVEBU_ALLEYCAT5 diff --git a/board/alliedtelesis/x220/.gitattributes b/board/alliedtelesis/x220/.gitattributes new file mode 100644 index 000000000000..2aeb4eee6416 --- /dev/null +++ b/board/alliedtelesis/x220/.gitattributes @@ -0,0 +1 @@ +binary.0 binary diff --git a/board/alliedtelesis/x220/.gitignore b/board/alliedtelesis/x220/.gitignore new file mode 100644 index 000000000000..775b9346b859 --- /dev/null +++ b/board/alliedtelesis/x220/.gitignore @@ -0,0 +1 @@ +kwbimage.cfg diff --git a/board/alliedtelesis/x220/MAINTAINERS b/board/alliedtelesis/x220/MAINTAINERS new file mode 100644 index 000000000000..299ccda45e20 --- /dev/null +++ b/board/alliedtelesis/x220/MAINTAINERS @@ -0,0 +1,7 @@ +x220 BOARD +M: Chris Packham <[email protected]> +S: Maintained +F: board/alliedtelesis/x220 +F: include/configs/x220.h +F: configs/x220_defconfig +F: arch/arm/dts/armada-xp-atl-x220.dts diff --git a/board/alliedtelesis/x220/Makefile b/board/alliedtelesis/x220/Makefile new file mode 100644 index 000000000000..a74f0a769484 --- /dev/null +++ b/board/alliedtelesis/x220/Makefile @@ -0,0 +1,14 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# Copyright (C) 2025 Allied Telesis Labs + +obj-y := x220.o +extra-y := kwbimage.cfg + +quiet_cmd_sed = SED $@ + cmd_sed = sed $(SEDFLAGS_$(@F)) $< >$(dir $@)$(@F) + +SEDFLAGS_kwbimage.cfg =-e "s|^BINARY.*|BINARY $(srctree)/$(@D)/binary.0 0000005b 00000068|" +$(obj)/kwbimage.cfg: $(src)/kwbimage.cfg.in include/autoconf.mk \ + include/config/auto.conf + $(call if_changed,sed) diff --git a/board/alliedtelesis/x220/README b/board/alliedtelesis/x220/README new file mode 100644 index 000000000000..b90f0f879ddf --- /dev/null +++ b/board/alliedtelesis/x220/README @@ -0,0 +1,4 @@ +To generate binary.0 from Marvell's bin_hdr.elf use the following command + + arm-softfloat-linux-gnueabi-objcopy -S -O binary bin_hdr.elf \ + board/alliedtelesis/x220/binary.0 diff --git a/board/alliedtelesis/x220/binary.0 b/board/alliedtelesis/x220/binary.0 new file mode 100644 index 0000000000000000000000000000000000000000..8dd687286a001c5df3cbc878d527d2a764f8c40b GIT binary patch literal 423 zcmYk2F>b>!3`KXHf(NjDfNtqhWN3z>MaF`*7)y;z29zAvw=ZR<MFmad=l_pv+x@xo z;q7!hy*#-`p>^*eX1K&ekb}(0!ysHRGL%5jNB#_6VI(HSLLT~cYly}%GA4LMy;Dl= zqkR@B5T{$BiOiuy;SLVj<Q8Cmm{qNjR^Te+A<f<lx1^YV4eq4bCL34?0^SMGSJh^6 zOE^%F<VhRIVnr+)%^vRJgd@R#3_blrUShG$3XrO3?wmVbV3qk{4_B7Owv{@xh+ZR) ze|uj<t5l&ERNvGvt_Als=K@TXOh9QP+aU{mm;IiB)Eq5*W3*GEt`G<f-ywS&8)UlG J%kTW1`vEC^lKcPw literal 0 HcmV?d00001 diff --git a/board/alliedtelesis/x220/kwbimage.cfg.in b/board/alliedtelesis/x220/kwbimage.cfg.in new file mode 100644 index 000000000000..8beda907ba45 --- /dev/null +++ b/board/alliedtelesis/x220/kwbimage.cfg.in @@ -0,0 +1,12 @@ +# +# Copyright (C) 2025 Allied Telesis Labs +# + +# Armada XP uses version 1 image format +VERSION 1 + +# Boot Media configurations +BOOT_FROM spi + +# Binary Header (bin_hdr) with DDR3 training code +BINARY board/alliedtelesis/x220/binary.0 0000005b 00000068 diff --git a/board/alliedtelesis/x220/x220.c b/board/alliedtelesis/x220/x220.c new file mode 100644 index 000000000000..7c9a73de9a24 --- /dev/null +++ b/board/alliedtelesis/x220/x220.c @@ -0,0 +1,67 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2025 Allied Telesis Labs + */ + +#include <i2c.h> +#include <init.h> +#include <asm/global_data.h> +#include <asm/gpio.h> +#include <linux/bitops.h> +#include <linux/mbus.h> +#include <linux/io.h> +#include <asm/arch/cpu.h> +#include <asm/arch/soc.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define X220_GPP_OUT_ENA_LOW (~(BIT(12) | BIT(17) | BIT(18) | BIT(31))) +#define X220_GPP_OUT_ENA_MID (~(0)) +#define X220_GPP_OUT_VAL_LOW (BIT(12) | BIT(18)) +#define X220_GPP_OUT_VAL_MID 0x0 +#define X220_GPP_POL_LOW 0x0 +#define X220_GPP_POL_MID 0x0 + +int board_early_init_f(void) +{ + /* Configure MPP */ + writel(0x44042222, MVEBU_MPP_BASE + 0x00); + writel(0x11000004, MVEBU_MPP_BASE + 0x04); + writel(0x44444004, MVEBU_MPP_BASE + 0x08); + writel(0x04444444, MVEBU_MPP_BASE + 0x0c); + writel(0x00000004, MVEBU_MPP_BASE + 0x10); + + /* Set GPP Out value */ + writel(X220_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00); + writel(X220_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00); + + /* Set GPP Polarity */ + writel(X220_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c); + writel(X220_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c); + + /* Set GPP Out Enable */ + writel(X220_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04); + writel(X220_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04); + + return 0; +} + +int board_init(void) +{ + /* address of boot parameters */ + gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; + + /* Disable MBUS Err Prop - in order to avoid data aborts */ + clrbits_le32(MVEBU_CPU_WIN_BASE + 0x200, (1 << 8)); + + return 0; +} + +#ifdef CONFIG_DISPLAY_BOARDINFO +int checkboard(void) +{ + puts("Board: Allied Telesis x220\n"); + + return 0; +} +#endif diff --git a/configs/x220_defconfig b/configs/x220_defconfig new file mode 100644 index 000000000000..4318f5e6ef1d --- /dev/null +++ b/configs/x220_defconfig @@ -0,0 +1,76 @@ +CONFIG_ARM=y +CONFIG_ARCH_CPU_INIT=y +CONFIG_ARCH_MVEBU=y +CONFIG_SYS_KWD_CONFIG="board/alliedtelesis/x220/kwbimage.cfg" +CONFIG_TEXT_BASE=0x00800000 +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000 +CONFIG_TARGET_X220=y +CONFIG_ENV_SIZE=0x10000 +CONFIG_ENV_OFFSET=0x100000 +CONFIG_ENV_SECT_SIZE=0x40000 +CONFIG_DEFAULT_DEVICE_TREE="armada-xp-atl-x220" +CONFIG_SYS_LOAD_ADDR=0x800000 +CONFIG_PCI=y +CONFIG_SYS_MEMTEST_START=0x00800000 +CONFIG_SYS_MEMTEST_END=0x00ffffff +CONFIG_FIT=y +CONFIG_FIT_VERBOSE=y +CONFIG_FIT_BEST_MATCH=y +CONFIG_USE_PREBOOT=y +CONFIG_SYS_CONSOLE_INFO_QUIET=y +CONFIG_SYS_MAXARGS=96 +CONFIG_CMD_MEMTEST=y +CONFIG_SYS_ALT_MEMTEST=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_SPI=y +CONFIG_CMD_USB=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_TFTPPUT=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_MII=y +CONFIG_CMD_PING=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_TIME=y +CONFIG_CMD_EXT2=y +CONFIG_CMD_EXT4=y +CONFIG_CMD_FAT=y +CONFIG_CMD_FS_GENERIC=y +CONFIG_CMD_MTDPARTS=y +CONFIG_MTDIDS_DEFAULT="nand0=nand" +CONFIG_MTDPARTS_DEFAULT="mtdparts=nand:112M(user),8M(errlog),8M(nand-bbt)" +CONFIG_CMD_UBI=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_IN_SPI_FLASH=y +CONFIG_ENV_RELOC_GD_ENV_ADDR=y +CONFIG_ARP_TIMEOUT=200 +CONFIG_NET_RETRY_COUNT=50 +CONFIG_GPIO_HOG=y +CONFIG_DM_PCA953X=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_MVTWSI=y +# CONFIG_MMC is not set +CONFIG_MTD_RAW_NAND=y +CONFIG_SYS_NAND_USE_FLASH_BBT=y +CONFIG_NAND_PXA3XX=y +CONFIG_SYS_NAND_ONFI_DETECTION=y +CONFIG_SPI_FLASH_SFDP_SUPPORT=y +CONFIG_SPI_FLASH_MACRONIX=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_SST=y +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set +CONFIG_PCI_MVEBU=y +CONFIG_SYS_NS16550=y +CONFIG_KIRKWOOD_SPI=y +CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_STORAGE=y +CONFIG_USB_HOST_ETHER=y +CONFIG_USB_ETHER_ASIX=y +CONFIG_USB_ETHER_ASIX88179=y +CONFIG_USB_ETHER_MCS7830=y +CONFIG_USB_ETHER_RTL8152=y +CONFIG_USB_ETHER_SMSC95XX=y +CONFIG_WDT=y +CONFIG_WDT_ORION=y diff --git a/include/configs/x220.h b/include/configs/x220.h new file mode 100644 index 000000000000..3022ad491b7e --- /dev/null +++ b/include/configs/x220.h @@ -0,0 +1,20 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright (C) 2025 Allied Telesis Labs + */ + +#ifndef _CONFIG_X220_H +#define _CONFIG_X220_H + +/* Keep device tree and initrd in lower memory so the kernel can access them */ +#define CFG_EXTRA_ENV_SETTINGS \ + "fdt_high=0x10000000\0" \ + "initrd_high=0x10000000\0" + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +#endif /* _CONFIG_X220_H */ -- 2.52.0
