The kernel gadget API has parts u-boot does not use. Drop them and fix up ch9.h so the gadget code matches the new DWC3 driver.
Co-developed-by: Jerome Forissier <[email protected]> Signed-off-by: Jerome Forissier <[email protected]> Co-developed-by: Jens Wiklander <[email protected]> Signed-off-by: Jens Wiklander <[email protected]> Signed-off-by: Anders Roxell <[email protected]> --- include/linux/usb/ch9.h | 25 +- include/linux/usb/gadget.h | 520 +++++++------------------------------ 2 files changed, 107 insertions(+), 438 deletions(-) diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h index c8c553b930ac..6623c6ae95b3 100644 --- a/include/linux/usb/ch9.h +++ b/include/linux/usb/ch9.h @@ -1,3 +1,4 @@ +/* SPDX-License-Identifier: GPL-2.0 */ /* * This file holds USB constants and structures that are needed for * USB device APIs. These are used by the USB device model, which is @@ -5,7 +6,7 @@ * Wireless USB 1.0 (spread around). Linux has several APIs in C that * need these: * - * - the master/host side Linux-USB kernel driver API; + * - the host side Linux-USB kernel driver API; * - the "usbfs" user space API; and * - the Linux "gadget" slave/device/peripheral side driver API. * @@ -131,11 +132,11 @@ * Test Mode Selectors * See USB 2.0 spec Table 9-7 */ -#define TEST_J 1 -#define TEST_K 2 -#define TEST_SE0_NAK 3 -#define TEST_PACKET 4 -#define TEST_FORCE_EN 5 +#define USB_TEST_J 1 +#define USB_TEST_K 2 +#define USB_TEST_SE0_NAK 3 +#define USB_TEST_PACKET 4 +#define USB_TEST_FORCE_ENABLE 5 /* * New Feature Selectors as added by USB 3.0 @@ -873,9 +874,6 @@ struct usb_ss_cap_descriptor { /* Link Power Management */ __le16 bU2DevExitLat; } __attribute__((packed)); -#define USB_DEFAULT_U1_DEV_EXIT_LAT 0x01 /* Less then 1 microsec */ -#define USB_DEFAULT_U2_DEV_EXIT_LAT 0x01F4 /* Less then 500 microsec */ - #define USB_DT_USB_SS_CAP_SIZE 10 /* @@ -1055,4 +1053,13 @@ struct usb_string { const char *s; }; +/* USB 3.2 SuperSpeed Plus phy signaling rate generation and lane count */ + +enum usb_ssp_rate { + USB_SSP_GEN_UNKNOWN = 0, + USB_SSP_GEN_2x1, + USB_SSP_GEN_1x2, + USB_SSP_GEN_2x2, +}; + #endif /* __LINUX_USB_CH9_H */ diff --git a/include/linux/usb/gadget.h b/include/linux/usb/gadget.h index fe79bf64a0e1..e0f67475b537 100644 --- a/include/linux/usb/gadget.h +++ b/include/linux/usb/gadget.h @@ -88,6 +88,7 @@ struct usb_request { dma_addr_t dma; unsigned stream_id:16; + unsigned is_last:1; unsigned no_interrupt:1; unsigned zero:1; unsigned short_not_ok:1; @@ -97,6 +98,7 @@ struct usb_request { void *context; struct list_head list; + unsigned frame_number; /* ISO ONLY */ int status; unsigned actual; }; @@ -153,6 +155,8 @@ struct usb_ep_caps { * @ops: Function pointers used to access hardware-specific operations. * @ep_list:the gadget's ep_list holds all of its endpoints * @caps:The structure describing types and directions supported by endoint. + * @enabled: The current endpoint enabled/disabled state. + * @claimed: True if this endpoint is claimed by a function. * @maxpacket:The maximum packet size used on this endpoint. The initial * value can sometimes be reduced (hardware allowing), according to * the endpoint descriptor used to configure the endpoint. @@ -162,6 +166,8 @@ struct usb_ep_caps { * @max_streams: The maximum number of streams supported * by this EP (0 - 16, actual number is 2^n) * @maxburst: the maximum number of bursts supported by this EP (for usb3) + * @address: used to identify the endpoint when finding descriptor that + * matches connection speed * @driver_data:for use by the gadget driver. all other fields are * read-only to gadget drivers. * @desc: endpoint descriptor. This pointer is set before the endpoint is @@ -179,301 +185,73 @@ struct usb_ep { const struct usb_ep_ops *ops; struct list_head ep_list; struct usb_ep_caps caps; + bool claimed; bool enabled; unsigned maxpacket:16; unsigned maxpacket_limit:16; unsigned max_streams:16; unsigned maxburst:5; + u8 address; const struct usb_endpoint_descriptor *desc; const struct usb_ss_ep_comp_descriptor *comp_desc; }; /*-------------------------------------------------------------------------*/ -/** - * usb_ep_set_maxpacket_limit - set maximum packet size limit for endpoint - * @ep:the endpoint being configured - * @maxpacket_limit:value of maximum packet size limit - * - * This function shoud be used only in UDC drivers to initialize endpoint - * (usually in probe function). - */ +#if IS_ENABLED(CONFIG_USB_GADGET) +void usb_ep_set_maxpacket_limit(struct usb_ep *ep, unsigned maxpacket_limit); +int usb_ep_enable(struct usb_ep *ep); +int usb_ep_disable(struct usb_ep *ep); +struct usb_request *usb_ep_alloc_request(struct usb_ep *ep, gfp_t gfp_flags); +void usb_ep_free_request(struct usb_ep *ep, struct usb_request *req); +int usb_ep_queue(struct usb_ep *ep, struct usb_request *req, gfp_t gfp_flags); +int usb_ep_dequeue(struct usb_ep *ep, struct usb_request *req); +int usb_ep_set_halt(struct usb_ep *ep); +int usb_ep_clear_halt(struct usb_ep *ep); +int usb_ep_set_wedge(struct usb_ep *ep); +int usb_ep_fifo_status(struct usb_ep *ep); +void usb_ep_fifo_flush(struct usb_ep *ep); +#else static inline void usb_ep_set_maxpacket_limit(struct usb_ep *ep, - unsigned maxpacket_limit) -{ - ep->maxpacket_limit = maxpacket_limit; - ep->maxpacket = maxpacket_limit; -} - -/** - * usb_ep_enable - configure endpoint, making it usable - * @ep:the endpoint being configured. may not be the endpoint named "ep0". - * drivers discover endpoints through the ep_list of a usb_gadget. - * @desc:descriptor for desired behavior. caller guarantees this pointer - * remains valid until the endpoint is disabled; the data byte order - * is little-endian (usb-standard). - * - * when configurations are set, or when interface settings change, the driver - * will enable or disable the relevant endpoints. while it is enabled, an - * endpoint may be used for i/o until the driver receives a disconnect() from - * the host or until the endpoint is disabled. - * - * the ep0 implementation (which calls this routine) must ensure that the - * hardware capabilities of each endpoint match the descriptor provided - * for it. for example, an endpoint named "ep2in-bulk" would be usable - * for interrupt transfers as well as bulk, but it likely couldn't be used - * for iso transfers or for endpoint 14. some endpoints are fully - * configurable, with more generic names like "ep-a". (remember that for - * USB, "in" means "towards the USB master".) - * - * returns zero, or a negative error code. - */ -static inline int usb_ep_enable(struct usb_ep *ep, - const struct usb_endpoint_descriptor *desc) -{ - int ret; - - if (ep->enabled) - return 0; - - ret = ep->ops->enable(ep, desc); - if (ret) - return ret; - - ep->enabled = true; - - return 0; -} - -/** - * usb_ep_disable - endpoint is no longer usable - * @ep:the endpoint being unconfigured. may not be the endpoint named "ep0". - * - * no other task may be using this endpoint when this is called. - * any pending and uncompleted requests will complete with status - * indicating disconnect (-ESHUTDOWN) before this call returns. - * gadget drivers must call usb_ep_enable() again before queueing - * requests to the endpoint. - * - * returns zero, or a negative error code. - */ + unsigned maxpacket_limit) +{ } +static inline int usb_ep_enable(struct usb_ep *ep) +{ return 0; } static inline int usb_ep_disable(struct usb_ep *ep) -{ - int ret; - - if (!ep->enabled) - return 0; - - ret = ep->ops->disable(ep); - if (ret) - return ret; - - ep->enabled = false; - - return 0; -} - -/** - * usb_ep_alloc_request - allocate a request object to use with this endpoint - * @ep:the endpoint to be used with with the request - * @gfp_flags:GFP_* flags to use - * - * Request objects must be allocated with this call, since they normally - * need controller-specific setup and may even need endpoint-specific - * resources such as allocation of DMA descriptors. - * Requests may be submitted with usb_ep_queue(), and receive a single - * completion callback. Free requests with usb_ep_free_request(), when - * they are no longer needed. - * - * Returns the request, or null if one could not be allocated. - */ +{ return 0; } static inline struct usb_request *usb_ep_alloc_request(struct usb_ep *ep, - gfp_t gfp_flags) -{ - return ep->ops->alloc_request(ep, gfp_flags); -} - -/** - * usb_ep_free_request - frees a request object - * @ep:the endpoint associated with the request - * @req:the request being freed - * - * Reverses the effect of usb_ep_alloc_request(). - * Caller guarantees the request is not queued, and that it will - * no longer be requeued (or otherwise used). - */ + gfp_t gfp_flags) +{ return NULL; } static inline void usb_ep_free_request(struct usb_ep *ep, - struct usb_request *req) -{ - ep->ops->free_request(ep, req); -} - -/** - * usb_ep_queue - queues (submits) an I/O request to an endpoint. - * @ep:the endpoint associated with the request - * @req:the request being submitted - * @gfp_flags: GFP_* flags to use in case the lower level driver couldn't - * pre-allocate all necessary memory with the request. - * - * This tells the device controller to perform the specified request through - * that endpoint (reading or writing a buffer). When the request completes, - * including being canceled by usb_ep_dequeue(), the request's completion - * routine is called to return the request to the driver. Any endpoint - * (except control endpoints like ep0) may have more than one transfer - * request queued; they complete in FIFO order. Once a gadget driver - * submits a request, that request may not be examined or modified until it - * is given back to that driver through the completion callback. - * - * Each request is turned into one or more packets. The controller driver - * never merges adjacent requests into the same packet. OUT transfers - * will sometimes use data that's already buffered in the hardware. - * Drivers can rely on the fact that the first byte of the request's buffer - * always corresponds to the first byte of some USB packet, for both - * IN and OUT transfers. - * - * Bulk endpoints can queue any amount of data; the transfer is packetized - * automatically. The last packet will be short if the request doesn't fill it - * out completely. Zero length packets (ZLPs) should be avoided in portable - * protocols since not all usb hardware can successfully handle zero length - * packets. (ZLPs may be explicitly written, and may be implicitly written if - * the request 'zero' flag is set.) Bulk endpoints may also be used - * for interrupt transfers; but the reverse is not true, and some endpoints - * won't support every interrupt transfer. (Such as 768 byte packets.) - * - * Interrupt-only endpoints are less functional than bulk endpoints, for - * example by not supporting queueing or not handling buffers that are - * larger than the endpoint's maxpacket size. They may also treat data - * toggle differently. - * - * Control endpoints ... after getting a setup() callback, the driver queues - * one response (even if it would be zero length). That enables the - * status ack, after transfering data as specified in the response. Setup - * functions may return negative error codes to generate protocol stalls. - * (Note that some USB device controllers disallow protocol stall responses - * in some cases.) When control responses are deferred (the response is - * written after the setup callback returns), then usb_ep_set_halt() may be - * used on ep0 to trigger protocol stalls. - * - * For periodic endpoints, like interrupt or isochronous ones, the usb host - * arranges to poll once per interval, and the gadget driver usually will - * have queued some data to transfer at that time. - * - * Returns zero, or a negative error code. Endpoints that are not enabled - * report errors; errors will also be - * reported when the usb peripheral is disconnected. - */ -static inline int usb_ep_queue(struct usb_ep *ep, - struct usb_request *req, gfp_t gfp_flags) -{ - return ep->ops->queue(ep, req, gfp_flags); -} - -/** - * usb_ep_dequeue - dequeues (cancels, unlinks) an I/O request from an endpoint - * @ep:the endpoint associated with the request - * @req:the request being canceled - * - * if the request is still active on the endpoint, it is dequeued and its - * completion routine is called (with status -ECONNRESET); else a negative - * error code is returned. - * - * note that some hardware can't clear out write fifos (to unlink the request - * at the head of the queue) except as part of disconnecting from usb. such - * restrictions prevent drivers from supporting configuration changes, - * even to configuration zero (a "chapter 9" requirement). - */ + struct usb_request *req) +{ } +static inline int usb_ep_queue(struct usb_ep *ep, struct usb_request *req, + gfp_t gfp_flags) +{ return 0; } static inline int usb_ep_dequeue(struct usb_ep *ep, struct usb_request *req) -{ - return ep->ops->dequeue(ep, req); -} - -/** - * usb_ep_set_halt - sets the endpoint halt feature. - * @ep: the non-isochronous endpoint being stalled - * - * Use this to stall an endpoint, perhaps as an error report. - * Except for control endpoints, - * the endpoint stays halted (will not stream any data) until the host - * clears this feature; drivers may need to empty the endpoint's request - * queue first, to make sure no inappropriate transfers happen. - * - * Note that while an endpoint CLEAR_FEATURE will be invisible to the - * gadget driver, a SET_INTERFACE will not be. To reset endpoints for the - * current altsetting, see usb_ep_clear_halt(). When switching altsettings, - * it's simplest to use usb_ep_enable() or usb_ep_disable() for the endpoints. - * - * Returns zero, or a negative error code. On success, this call sets - * underlying hardware state that blocks data transfers. - * Attempts to halt IN endpoints will fail (returning -EAGAIN) if any - * transfer requests are still queued, or if the controller hardware - * (usually a FIFO) still holds bytes that the host hasn't collected. - */ +{ return 0; } static inline int usb_ep_set_halt(struct usb_ep *ep) -{ - return ep->ops->set_halt(ep, 1); -} - -/** - * usb_ep_clear_halt - clears endpoint halt, and resets toggle - * @ep:the bulk or interrupt endpoint being reset - * - * Use this when responding to the standard usb "set interface" request, - * for endpoints that aren't reconfigured, after clearing any other state - * in the endpoint's i/o queue. - * - * Returns zero, or a negative error code. On success, this call clears - * the underlying hardware state reflecting endpoint halt and data toggle. - * Note that some hardware can't support this request (like pxa2xx_udc), - * and accordingly can't correctly implement interface altsettings. - */ +{ return 0; } static inline int usb_ep_clear_halt(struct usb_ep *ep) -{ - return ep->ops->set_halt(ep, 0); -} - -/** - * usb_ep_fifo_status - returns number of bytes in fifo, or error - * @ep: the endpoint whose fifo status is being checked. - * - * FIFO endpoints may have "unclaimed data" in them in certain cases, - * such as after aborted transfers. Hosts may not have collected all - * the IN data written by the gadget driver (and reported by a request - * completion). The gadget driver may not have collected all the data - * written OUT to it by the host. Drivers that need precise handling for - * fault reporting or recovery may need to use this call. - * - * This returns the number of such bytes in the fifo, or a negative - * errno if the endpoint doesn't use a FIFO or doesn't support such - * precise handling. - */ +{ return 0; } +static inline int usb_ep_set_wedge(struct usb_ep *ep) +{ return 0; } static inline int usb_ep_fifo_status(struct usb_ep *ep) -{ - if (ep->ops->fifo_status) - return ep->ops->fifo_status(ep); - else - return -EOPNOTSUPP; -} - -/** - * usb_ep_fifo_flush - flushes contents of a fifo - * @ep: the endpoint whose fifo is being flushed. - * - * This call may be used to flush the "unclaimed data" that may exist in - * an endpoint fifo after abnormal transaction terminations. The call - * must never be used except when endpoint is not being used for any - * protocol translation. - */ +{ return 0; } static inline void usb_ep_fifo_flush(struct usb_ep *ep) -{ - if (ep->ops->fifo_flush) - ep->ops->fifo_flush(ep); -} +{ } +#endif /* USB_GADGET */ /*-------------------------------------------------------------------------*/ struct usb_dcd_config_params { __u8 bU1devExitLat; /* U1 Device exit Latency */ +#define USB_DEFAULT_U1_DEV_EXIT_LAT 0x01 /* Less then 1 microsec */ __le16 bU2DevExitLat; /* U2 Device exit Latency */ +#define USB_DEFAULT_U2_DEV_EXIT_LAT 0x1F4 /* Less then 500 microsec */ + __u8 besl_baseline; /* Recommended baseline BESL (0-15) */ + __u8 besl_deep; /* Recommended deep BESL (0-15) */ +#define USB_DEFAULT_BESL_UNSPECIFIED 0xFF /* No recommended value */ }; struct usb_gadget; @@ -491,7 +269,8 @@ struct usb_gadget_ops { int (*pullup) (struct usb_gadget *, int is_on); int (*ioctl)(struct usb_gadget *, unsigned code, unsigned long param); - void (*get_config_params)(struct usb_dcd_config_params *); + void (*get_config_params)(struct usb_gadget *, + struct usb_dcd_config_params *); int (*udc_start)(struct usb_gadget *, struct usb_gadget_driver *); int (*udc_stop)(struct usb_gadget *); @@ -503,6 +282,10 @@ struct usb_gadget_ops { struct usb_endpoint_descriptor *); void (*udc_set_speed)(struct usb_gadget *gadget, enum usb_device_speed); + void (*udc_set_ssp_rate)(struct usb_gadget *gadget, + enum usb_ssp_rate rate); + void (*udc_async_callbacks)(struct usb_gadget *gadget, bool enable); + int (*check_config)(struct usb_gadget *gadget); }; /** @@ -552,13 +335,23 @@ struct usb_gadget_ops { * device is acting as a B-Peripheral (so is_a_peripheral is false). */ struct usb_gadget { + struct usb_udc *udc; /* readonly to gadget driver */ const struct usb_gadget_ops *ops; struct usb_ep *ep0; struct list_head ep_list; /* of usb_ep */ enum usb_device_speed speed; enum usb_device_speed max_speed; + + /* USB SuperSpeed Plus only */ + enum usb_ssp_rate ssp_rate; + enum usb_ssp_rate max_ssp_rate; + enum usb_device_state state; + unsigned isoch_delay; + + unsigned out_epnum; + unsigned in_epnum; unsigned is_dualspeed:1; unsigned is_otg:1; unsigned is_a_peripheral:1; @@ -568,6 +361,10 @@ struct usb_gadget { const char *name; struct device dev; unsigned quirk_ep_out_aligned_size:1; + unsigned is_selfpowered:1; + unsigned deactivated:1; + unsigned wakeup_armed:1; + unsigned connected:1; }; static inline void set_gadget_data(struct usb_gadget *gadget, void *data) @@ -585,6 +382,15 @@ static inline struct usb_gadget *dev_to_usb_gadget(struct device *dev) return container_of(dev, struct usb_gadget, dev); } +static inline void usb_put_gadget(struct usb_gadget *gadget) +{ +} + +void usb_initialize_gadget(struct device *parent, + struct usb_gadget *gadget, + void (*release)(struct device *dev)); +int usb_add_gadget(struct usb_gadget *gadget); + /* iterates the non-control endpoints; 'tmp' is a struct usb_ep pointer */ #define gadget_for_each_ep(tmp, gadget) \ list_for_each_entry(tmp, &(gadget)->ep_list, ep_list) @@ -630,168 +436,18 @@ static inline int gadget_is_superspeed(struct usb_gadget *g) return g->max_speed >= USB_SPEED_SUPER; } -/** - * usb_gadget_frame_number - returns the current frame number - * @gadget: controller that reports the frame number - * - * Returns the usb frame number, normally eleven bits from a SOF packet, - * or negative errno if this device doesn't support this capability. - */ -static inline int usb_gadget_frame_number(struct usb_gadget *gadget) -{ - return gadget->ops->get_frame(gadget); -} - -/** - * usb_gadget_wakeup - tries to wake up the host connected to this gadget - * @gadget: controller used to wake up the host - * - * Returns zero on success, else negative error code if the hardware - * doesn't support such attempts, or its support has not been enabled - * by the usb host. Drivers must return device descriptors that report - * their ability to support this, or hosts won't enable it. - * - * This may also try to use SRP to wake the host and start enumeration, - * even if OTG isn't otherwise in use. OTG devices may also start - * remote wakeup even when hosts don't explicitly enable it. - */ -static inline int usb_gadget_wakeup(struct usb_gadget *gadget) -{ - if (!gadget->ops->wakeup) - return -EOPNOTSUPP; - return gadget->ops->wakeup(gadget); -} - -/** - * usb_gadget_set_selfpowered - sets the device selfpowered feature. - * @gadget:the device being declared as self-powered - * - * this affects the device status reported by the hardware driver - * to reflect that it now has a local power supply. - * - * returns zero on success, else negative errno. - */ -static inline int usb_gadget_set_selfpowered(struct usb_gadget *gadget) -{ - if (!gadget->ops->set_selfpowered) - return -EOPNOTSUPP; - return gadget->ops->set_selfpowered(gadget, 1); -} - -/** - * usb_gadget_clear_selfpowered - clear the device selfpowered feature. - * @gadget:the device being declared as bus-powered - * - * this affects the device status reported by the hardware driver. - * some hardware may not support bus-powered operation, in which - * case this feature's value can never change. - * - * returns zero on success, else negative errno. - */ -static inline int usb_gadget_clear_selfpowered(struct usb_gadget *gadget) -{ - if (!gadget->ops->set_selfpowered) - return -EOPNOTSUPP; - return gadget->ops->set_selfpowered(gadget, 0); -} - -/** - * usb_gadget_vbus_connect - Notify controller that VBUS is powered - * @gadget:The device which now has VBUS power. - * - * This call is used by a driver for an external transceiver (or GPIO) - * that detects a VBUS power session starting. Common responses include - * resuming the controller, activating the D+ (or D-) pullup to let the - * host detect that a USB device is attached, and starting to draw power - * (8mA or possibly more, especially after SET_CONFIGURATION). - * - * Returns zero on success, else negative errno. - */ -static inline int usb_gadget_vbus_connect(struct usb_gadget *gadget) -{ - if (!gadget->ops->vbus_session) - return -EOPNOTSUPP; - return gadget->ops->vbus_session(gadget, 1); -} - -/** - * usb_gadget_vbus_draw - constrain controller's VBUS power usage - * @gadget:The device whose VBUS usage is being described - * @mA:How much current to draw, in milliAmperes. This should be twice - * the value listed in the configuration descriptor bMaxPower field. - * - * This call is used by gadget drivers during SET_CONFIGURATION calls, - * reporting how much power the device may consume. For example, this - * could affect how quickly batteries are recharged. - * - * Returns zero on success, else negative errno. - */ -static inline int usb_gadget_vbus_draw(struct usb_gadget *gadget, unsigned mA) -{ - if (!gadget->ops->vbus_draw) - return -EOPNOTSUPP; - return gadget->ops->vbus_draw(gadget, mA); -} - -/** - * usb_gadget_vbus_disconnect - notify controller about VBUS session end - * @gadget:the device whose VBUS supply is being described - * - * This call is used by a driver for an external transceiver (or GPIO) - * that detects a VBUS power session ending. Common responses include - * reversing everything done in usb_gadget_vbus_connect(). - * - * Returns zero on success, else negative errno. - */ -static inline int usb_gadget_vbus_disconnect(struct usb_gadget *gadget) -{ - if (!gadget->ops->vbus_session) - return -EOPNOTSUPP; - return gadget->ops->vbus_session(gadget, 0); -} - -/** - * usb_gadget_connect - software-controlled connect to USB host - * @gadget:the peripheral being connected - * - * Enables the D+ (or potentially D-) pullup. The host will start - * enumerating this gadget when the pullup is active and a VBUS session - * is active (the link is powered). This pullup is always enabled unless - * usb_gadget_disconnect() has been used to disable it. - * - * Returns zero on success, else negative errno. - */ -static inline int usb_gadget_connect(struct usb_gadget *gadget) -{ - if (!gadget->ops->pullup) - return -EOPNOTSUPP; - return gadget->ops->pullup(gadget, 1); -} - -/** - * usb_gadget_disconnect - software-controlled disconnect from USB host - * @gadget:the peripheral being disconnected - * - * Disables the D+ (or potentially D-) pullup, which the host may see - * as a disconnect (when a VBUS session is active). Not all systems - * support software pullup controls. - * - * This routine may be used during the gadget driver bind() call to prevent - * the peripheral from ever being visible to the USB host, unless later - * usb_gadget_connect() is called. For example, user mode components may - * need to be activated before the system can talk to hosts. - * - * Returns zero on success, else negative errno. - */ -static inline int usb_gadget_disconnect(struct usb_gadget *gadget) -{ - if (!gadget->ops->pullup) - return -EOPNOTSUPP; - return gadget->ops->pullup(gadget, 0); -} +int usb_gadget_frame_number(struct usb_gadget *gadget); +int usb_gadget_wakeup(struct usb_gadget *gadget); +int usb_gadget_set_selfpowered(struct usb_gadget *gadget); +int usb_gadget_clear_selfpowered(struct usb_gadget *gadget); +int usb_gadget_vbus_draw(struct usb_gadget *gadget, unsigned mA); +int usb_gadget_vbus_disconnect(struct usb_gadget *gadget); +int usb_gadget_connect(struct usb_gadget *gadget); +int usb_gadget_disconnect(struct usb_gadget *gadget); /*-------------------------------------------------------------------------*/ + /** * struct usb_gadget_driver - driver for usb 'slave' devices * @function: String describing the gadget's function @@ -980,6 +636,12 @@ extern void usb_gadget_giveback_request(struct usb_ep *ep, /*-------------------------------------------------------------------------*/ +/* utility to check if endpoint caps match descriptor needs */ + +extern int usb_gadget_ep_match_desc(struct usb_gadget *gadget, + struct usb_ep *ep, struct usb_endpoint_descriptor *desc, + struct usb_ss_ep_comp_descriptor *ep_comp); + /* utility wrapping a simple endpoint selection policy */ extern struct usb_ep *usb_ep_autoconfig(struct usb_gadget *, -- 2.53.0
