Dear Felix Radensky, > Hi Marek, > > Can you please take a look at this problem.
Can you please avoid top-posting? Does U-Boot even support your USB device? > Thanks a lot. > > Felix. > > On 11/02/2012 08:38 AM, Felix Radensky wrote: > > Hi, > > > > I'm running u-boot-2012.10 on a custom DM37x based board. > > The board has LAN9514 USB Ethernet adapter connected > > in EHCI host controller via USB3320 ULPI PHY. This is very > > similar to BeagleBoard XM. Both Ethernet and USB hub work > > in linux-2.6.37 from TI PSP 04.02.00.07. In u-boot however, > > neither Ethernet nor mass storage devices attached to hub > > are not detected. > > > > Below is boot log: > > > > U-Boot 2012.10 (Nov 02 2012 - 00:44:41) > > > > OMAP36XX/37XX-GP ES1.2, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz > > Pro4Tech MVC404 board + LPDDR/NAND > > I2C: ready > > DRAM: 256 MiB > > NAND: 512 MiB > > MMC: OMAP SD/MMC: 0 > > In: serial > > Out: serial > > Err: serial > > Net: Net Initialization Skipped > > No ethernet found. > > Hit any key to stop autoboot: 0 > > MVC404 > usb start > > (Re)start USB... > > USB: Register 1313 NbrPorts 3 > > USB EHCI 1.00 > > scanning bus for devices... 1 USB Device(s) found > > > > scanning bus for storage devices... 0 Storage Device(s) found > > scanning bus for ethernet devices... 0 Ethernet Device(s) found > > > > MVC404 > usb info > > 1: Hub, USB Revision 2.0 > > > > - u-boot EHCI Host Controller > > - Class: Hub > > - PacketSize: 64 Configurations: 1 > > - Vendor: 0x0000 Product 0x0000 Version 1.0 > > > > Configuration: 1 > > - Interfaces: 1 Self Powered 0mA > > > > Interface: 0 > > - Alternate Setting 0, Endpoints: 1 > > - Class Hub > > - Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms > > > > I have the following definitions in the code: > > > > #define CONFIG_USB_OMAP3 > > #define CONFIG_USB_EHCI > > #define CONFIG_USB_EHCI_OMAP > > #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 > > #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 24 > > #define CONFIG_USB_ULPI > > #define CONFIG_USB_ULPI_VIEWPORT_OMAP > > #define CONFIG_USB_STORAGE > > > > static struct omap_usbhs_board_data usbhs_bdata = { > > > > .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, > > .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, > > .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED > > > > }; > > > > MUX_VAL(CP(ETK_D15_ES2), (IDIS | PTD | DIS | M4)) /*GPIO_24*/ > > > > I'd appreciate any help in fixing the problem. > > > > Thanks. > > > > Felix Radensky. > > _______________________________________________ > > U-Boot mailing list > > U-Boot@lists.denx.de > > http://lists.denx.de/mailman/listinfo/u-boot _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot