Clay, Did you run the actual tests on the RB493s or computers on each end? On Fri, Dec 5, 2014 at 10:22 PM, Clay Stewart < [email protected]> wrote:
> MT 493Gs on ends, going through ubnt TSs, gig surges and standard AF POEs. > > > On Friday, December 5, 2014, RickG <[email protected]> wrote: > >> Clay, I havent had a chance to go back with my laptop to run Iperf from >> it yet. Yes, I run all AFs from the included POE using gigabit surge >> protectors. My initial tests at this tower upon installation a year ago >> were limited by my laptop only having a 100Mb port. Since then, I purchased >> a USB gigabit adapter for it which runs upstream http tests slightly over >> 100Mbps. Thought: Maybe the USB port cant handle it? Exactly how did you >> run your tests? >> >> On Fri, Dec 5, 2014 at 3:20 PM, Clay Stewart < >> [email protected]> wrote: >> >>> Rick, late on this issu, was it the switch, do not read where you said >>> it was.... I had an issue similar, turned out to be I had accidentally >>> placed a 100M surge protector instead of a gig. Also, I assume you are >>> powering AF with included POE, and not TSes (they do not have amps). We run >>> with the included POE, with LAN into unpowered TS 05/08 1Gb switch port and >>> get 777Mbps on test, TS to TS via AF to AF. >>> >>> On Thu, Dec 4, 2014 at 5:16 PM, Rory Conaway <[email protected]> >>> wrote: >>> >>>> So basically you just had a bad switch. Stuff happens. I think the >>>> first batch had some problem but after that, they have been pretty good for >>>> us but they don't show up in AC2 yet. >>>> >>>> >>>> >>>> The best small/cheap outdoor switches I've seen are the Tycons. >>>> Unfortunately, 100Mbps is so yesterday so we replaced them all with >>>> TS-5/8's. >>>> >>>> >>>> >>>> Rory >>>> >>>> >>>> >>>> *From:* [email protected] [mailto: >>>> [email protected]] *On Behalf Of *Josh Luthman >>>> *Sent:* Thursday, December 4, 2014 12:39 PM >>>> >>>> *To:* Ubiquiti Users Group >>>> *Subject:* Re: [Ubnt_users] Speed test no working >>>> >>>> >>>> >>>> I'm saying those ports won't work if the management interface doesn't >>>> work. In my case, my switches failed to respond to the management >>>> interface and the non-management ports stopped working as well (they did >>>> pass voltage, no eth link IIRC) >>>> >>>> >>>> >>>> >>>> Josh Luthman >>>> Office: 937-552-2340 >>>> Direct: 937-552-2343 >>>> 1100 Wayne St >>>> Suite 1337 >>>> Troy, OH 45373 >>>> >>>> >>>> >>>> On Thu, Dec 4, 2014 at 2:37 PM, Rory Conaway <[email protected]> >>>> wrote: >>>> >>>> Are you saying the TS-5/8 units can't handle 1Gbps on the ports? >>>> >>>> >>>> >>>> Rory >>>> >>>> >>>> >>>> *From:* [email protected] [mailto: >>>> [email protected]] *On Behalf Of *Josh Luthman >>>> *Sent:* Thursday, December 4, 2014 11:22 AM >>>> >>>> >>>> *To:* Ubiquiti Users Group >>>> *Subject:* Re: [Ubnt_users] Speed test no working >>>> >>>> >>>> >>>> No it doesn't... That's the real problem. >>>> >>>> Josh Luthman >>>> Office: 937-552-2340 >>>> Direct: 937-552-2343 >>>> 1100 Wayne St >>>> Suite 1337 >>>> Troy, OH 45373 >>>> >>>> On Dec 4, 2014 12:52 PM, "RickG" <[email protected]> wrote: >>>> >>>> About ToughSwitches: Should I assume as long as you dont use the >>>> management interface the unit will function fine as a gigabit switch? >>>> >>>> >>>> >>>> On Mon, Dec 1, 2014 at 4:32 PM, Josh Reynolds <[email protected]> >>>> wrote: >>>> >>>> Hardware, but management interface/cpu is only 100Mbps link internally. >>>> >>>> josh reynolds :: chief information officer >>>> >>>> spitwspots :: www.spitwspots.com >>>> >>>> On 12/01/2014 12:30 PM, Josh Luthman wrote: >>>> >>>> Are TS software or hardware switched? >>>> >>>> >>>> >>>> >>>> Josh Luthman >>>> Office: 937-552-2340 >>>> Direct: 937-552-2343 >>>> 1100 Wayne St >>>> Suite 1337 >>>> Troy, OH 45373 >>>> >>>> >>>> >>>> On Mon, Dec 1, 2014 at 4:29 PM, RickG <[email protected]> wrote: >>>> >>>> I know but I actually get a touch above 100 - like 104-106... >>>> >>>> >>>> >>>> On Mon, Dec 1, 2014 at 4:14 PM, Josh Luthman < >>>> [email protected]> wrote: >>>> >>>> A 100 meg limit sounds like a 100 BaseT problem to me, but who knows! >>>> >>>> >>>> >>>> >>>> Josh Luthman >>>> Office: 937-552-2340 >>>> Direct: 937-552-2343 >>>> 1100 Wayne St >>>> Suite 1337 >>>> Troy, OH 45373 >>>> >>>> >>>> >>>> On Mon, Dec 1, 2014 at 4:11 PM, RickG <[email protected]> wrote: >>>> >>>> Agreed. Just wanted to confirm. Will have to chase the problem down! >>>> >>>> >>>> >>>> On Mon, Dec 1, 2014 at 4:07 PM, Josh Luthman < >>>> [email protected]> wrote: >>>> >>>> You should be getting 770 megs on a test in either direction (even at >>>> the same time!) >>>> >>>> >>>> >>>> >>>> Josh Luthman >>>> Office: 937-552-2340 >>>> Direct: 937-552-2343 >>>> 1100 Wayne St >>>> Suite 1337 >>>> Troy, OH 45373 >>>> >>>> >>>> >>>> On Mon, Dec 1, 2014 at 4:06 PM, RickG <[email protected]> wrote: >>>> >>>> ToughSwitches on both ends on gigabit ports. I thought maybe laptop was >>>> maxed out until I ran IPerf from TS8 to TS8. >>>> >>>> >>>> >>>> On Mon, Dec 1, 2014 at 4:02 PM, Josh Luthman < >>>> [email protected]> wrote: >>>> >>>> 100 megabit switch between laptop and Airfiber? Is it linked at gig? >>>> Is your laptop's CPU maxed out? >>>> >>>> >>>> >>>> >>>> Josh Luthman >>>> Office: 937-552-2340 >>>> Direct: 937-552-2343 >>>> 1100 Wayne St >>>> Suite 1337 >>>> Troy, OH 45373 >>>> >>>> >>>> >>>> On Mon, Dec 1, 2014 at 4:00 PM, RickG <[email protected]> wrote: >>>> >>>> It might be the capacity but when I test I only get around 100Mbps. >>>> >>>> >>>> >>>> On Mon, Dec 1, 2014 at 3:50 PM, Mike Hammett <[email protected]> >>>> wrote: >>>> >>>> iPerf is not included with airFiber as it isn't needed. What it tells >>>> you the channel capacity is is what the channel capacity is. >>>> >>>> >>>> >>>> ----- >>>> Mike Hammett >>>> Intelligent Computing Solutions >>>> http://www.ics-il.com >>>> >>>> >>>> ------------------------------ >>>> >>>> *From: *"RickG" <[email protected]> >>>> *To: *"Ubiquiti Users Group" <[email protected]> >>>> *Sent: *Monday, December 1, 2014 2:48:52 PM >>>> >>>> >>>> *Subject: *Re: [Ubnt_users] Speed test no working >>>> >>>> Is there a trick to getting iperf to work on AirFiber? >>>> >>>> >>>> >>>> On Sun, Nov 16, 2014 at 4:01 PM, Adair Winter < >>>> [email protected]> wrote: >>>> >>>> I usually just SSH to the client radio/far side, run iperf -s then go >>>> to one of my servers in the data center and run iperf -c (client IP) -P5 >>>> >>>> works better than the web interface anyway >>>> >>>> >>>> >>>> >>>> >>>> On Sun, Nov 16, 2014 at 2:33 PM, Daniel Peoples <[email protected]> >>>> wrote: >>>> >>>> For speedtests I actually have a 5 year old bullet m5 in my NOC with >>>> the wlan disabled on the latest firmware, it has to be rebooted about once >>>> a month for it to work. >>>> >>>> Also, I don't know when they changed it, but for some reason the >>>> results of the speedtests(which I thought were UDP) are actually what I can >>>> real world get with TCP on that same circuit. Anyone know whats up with >>>> this? I have tested from several different points in our network with a >>>> variety of backhauls to that bulletm5 and get real world TCP speeds now a >>>> days. >>>> >>>> >>>> *Daniel Peoples* >>>> Resonance Broadband >>>> >>>> *Resonancebroadband.com* <http://Resonancebroadband.com> >>>> 918-429-3620 >>>> >>>> >>>> >>>> On Sun, Nov 16, 2014 at 2:25 PM, Tim Kerns <[email protected]> wrote: >>>> >>>> Not so easy to do....if you have, like me,some bullets or air grids.... >>>> then they can not have anything above 5.3 because you lose DFS. >>>> >>>> >>>> >>>> These were not re-certified by UBNT. >>>> >>>> >>>> >>>> :0 >>>> >>>> >>>> >>>> >>>> >>>> *From:* Rory Conaway >>>> >>>> *Sent:* Sunday, November 16, 2014 12:02 PM >>>> >>>> *To:* Ubiquiti Users Group >>>> >>>> *Subject:* Re: [Ubnt_users] Speed test no working >>>> >>>> >>>> >>>> Just get everything on 5.5.10. No reason not to. >>>> >>>> >>>> >>>> Rory >>>> >>>> >>>> >>>> *From:* [email protected] [mailto: >>>> [email protected]] *On Behalf Of *Jerry Richardson >>>> (airCloud) >>>> *Sent:* Sunday, November 16, 2014 12:01 PM >>>> *To:* Ubiquiti Users Group >>>> *Subject:* Re: [Ubnt_users] Speed test no working >>>> >>>> >>>> >>>> We have noticed that if the SW versions don't match it will not work. >>>> >>>> >>>> >>>> On Sun, Nov 16, 2014 at 10:49 AM, Daniel Peoples <[email protected]> >>>> wrote: >>>> >>>> This is something that has been an issue since 5.5 as far as I know. >>>> >>>> On Nov 16, 2014 11:18 AM, "Paul Conlin" <[email protected]> >>>> wrote: >>>> >>>> Is there a fix for this? A workaround besides rebooting? We are on >>>> 5.5.8. Should we move up to 5.5.10? >>>> >>>> >>>> >>>> PC >>>> >>>> Blaze Broadband >>>> >>>> >>>> >>>> >>>> >>>> *From:* [email protected] [mailto: >>>> [email protected]] *On Behalf Of *Daniel and Regina Peoples >>>> *Sent:* Tuesday, March 4, 2014 8:57 PM >>>> *To:* Ubiquiti Users Group >>>> *Subject:* Re: [Ubnt_users] Speed test no working >>>> >>>> >>>> >>>> This is a "Feature" of 5.5+ IIRC 5.3.5 didn't have this issue. >>>> >>>> >>>> *Daniel Peoples* >>>> Resonance Broadband >>>> >>>> *Resonancebroadband.com* <http://Resonancebroadband.com> >>>> 918-429-3620 >>>> >>>> >>>> >>>> On Tue, Mar 4, 2014 at 7:53 PM, RickG <[email protected]> wrote: >>>> >>>> Well, 5.5.4 sucks... >>>> >>>> >>>> >>>> On Tue, Mar 4, 2014 at 4:59 PM, Eduardo <[email protected]> wrote: >>>> >>>> Is this issue related to the firmware version? >>>> >>>> >>>> >>>> Eduardo >>>> >>>> >>>> >>>> ----- Original Message ----- >>>> >>>> *From:* Matt Hoppes >>>> >>>> *To:* Ubiquiti Users Group >>>> >>>> *Sent:* Tuesday, March 04, 2014 4:49 PM >>>> >>>> *Subject:* Re: [Ubnt_users] Speed test no working >>>> >>>> >>>> >>>> Reboot both radios -- there's some kind of a memory leak/issue. >>>> >>>> >>>> Matt Hoppes >>>> Director of Information Technology >>>> Indigo Wireless >>>> +1 (570) 723-7312 >>>> >>>> On 3/4/14, 4:48 PM, Eduardo wrote: >>>> > I'm trying to run a speed test from a station in a PtP link, and got >>>> > this message: >>>> > >>>> > Error: Specified device is not >>>> > compatible for speedtest. >>>> > >>>> > Both radios are BulletM5 with v5.5.4. I got the same error when tried >>>> in >>>> > a link with RocketM365 in both ends and v5.5.6. >>>> > >>>> > Also I've tried in a PtoP connection also with Bullets, but M2 and >>>> > v.5.5.6 with the same result. >>>> > >>>> > The issue is always running the speed test from the station to the >>>> AP. >>>> > >>>> > Have you guys seen this issue? >>>> > >>>> > Any suggestions on how I can fix it. >>>> > >>>> > Thanks, >>>> > Eduardo >>>> > >>>> > >>>> > >>>> > _______________________________________________ >>>> > Ubnt_users mailing list >>>> > [email protected] >>>> > http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> > >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> >>>> -- >>>> -RickG KyWiFi >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> ------------------------------ >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> >>>> -- >>>> >>>> Adair Winter >>>> VP, Network Operations / Owner >>>> Amarillo Wireless | 806.316.5071 >>>> C: 806.231.7180 >>>> http://www.amarillowireless.net >>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> >>>> -- >>>> >>>> -RickG KyWiFi >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> >>>> -- >>>> >>>> -RickG KyWiFi >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> >>>> -- >>>> >>>> -RickG KyWiFi >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> >>>> -- >>>> >>>> -RickG KyWiFi >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> >>>> -- >>>> >>>> -RickG KyWiFi >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> >>>> Ubnt_users mailing list >>>> >>>> [email protected] >>>> >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> >>>> >>>> -- >>>> >>>> -RickG KyWiFi >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>>> >>>> _______________________________________________ >>>> Ubnt_users mailing list >>>> [email protected] >>>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>>> >>>> >>> >>> >>> -- >>> >>> >>> -- >>> Clay Stewart, CEO >>> SCS Broadband >>> 434.263.6363 O >>> 434.942.6510 C >>> [email protected] >>> "We Keep You Up and Running" >>> >>> Please send sales inquiries to [email protected] >>> Please send service/repair requests to [email protected] >>> >>> _______________________________________________ >>> Ubnt_users mailing list >>> [email protected] >>> http://lists.wispa.org/mailman/listinfo/ubnt_users >>> >>> >> >> >> -- >> -RickG KyWiFi >> > > > -- > > > -- > Clay Stewart, CEO > SCS Broadband > 434.263.6363 O > 434.942.6510 C > [email protected] > "We Keep You Up and Running" > > Please send sales inquiries to [email protected] > Please send service/repair requests to [email protected] > > > _______________________________________________ > Ubnt_users mailing list > [email protected] > http://lists.wispa.org/mailman/listinfo/ubnt_users > > -- -RickG KyWiFi
_______________________________________________ Ubnt_users mailing list [email protected] http://lists.wispa.org/mailman/listinfo/ubnt_users
