Complementando ainda, li em outro forum para usar o dmesg e eis o resultado
[4295919.193000] usb-storage: device found at 2 [4295919.193000] usb-storage: waiting for device to settle before scanning [4295919.194000] usbcore: registered new driver usb-storage [4295919.194000] USB Mass Storage support registered. [4295924.198000] Vendor: Model: Rev: [4295924.198000] Type: Direct-Access ANSI SCSI revision : 00 [4295924.206000] usb-storage: device scan complete [4295924.335000] SCSI device sda: 1019617 512-byte hdwr sectors (522 MB) [4295924.340000] sda: Write Protect is off [4295924.340000] sda: Mode Sense: 00 c0 00 00 [4295924.340000] sda: assuming drive cache: write through [4295924.360000] SCSI device sda: 1019617 512-byte hdwr sectors (522 MB) [4295924.367000] sda: Write Protect is off [4295924.367000] sda: Mode Sense: 00 c0 00 00 [4295924.367000] sda: assuming drive cache: write through [4295924.367000] /dev/scsi/host0/bus0/target0/lun0: unknown partition table [4295924.403000] Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 [4296329.183000] atkbd.c: Unknown key pressed (translated set 2, code 0xaa on is a0060/serio0). [4296329.183000] atkbd.c: Use 'setkeycodes e02a <keycode>' to make it known. [4296329.345000] atkbd.c: Unknown key released (translated set 2, code 0xaa on i sa0060/serio0). [4296329.345000] atkbd.c: Use 'setkeycodes e02a <keycode>' to make it known. [4296329.529000] atkbd.c: Unknown key pressed (translated set 2, code 0xaa on is a0060/serio0). [4296329.529000] atkbd.c: Use 'setkeycodes e02a <keycode>' to make it known. [4296330.472000] atkbd.c: Unknown key released (translated set 2, code 0xaa on i sa0060/serio0). [4296330.472000] atkbd.c: Use 'setkeycodes e02a <keycode>' to make it known. [4296330.610000] atkbd.c: Unknown key pressed (translated set 2, code 0xaa on is a0060/serio0). [4296330.610000] atkbd.c: Use 'setkeycodes e02a <keycode>' to make it known. [4296330.747000] atkbd.c: Unknown key released (translated set 2, code 0xaa on i sa0060/serio0). [4296330.747000] atkbd.c: Use 'setkeycodes e02a <keycode>' to make it known. [EMAIL PROTECTED]:~$ Copie, acredito eu, a parte que interessa, mas se precisarem que faça de novo me avisem. Alguma dica depois disso? Em 13/02/06, Joao Guilherme <[EMAIL PROTECTED]> escreveu: > > Galera o erro que aparece quando tento clicar duas vezes no ícone do > pendrive é o seguinte: > > Error: given UDI is not a mountable volume > > Como sou novato alguém me explica isso? > > Além disso tentei o que vocês postaram aqui e na hora de montar recebo a > seguinte mensagem: > > [EMAIL PROTECTED]:~$ sudo mount /dev/sda1 -t vfat /media/pendrive > mount: o ponto de montagem /media/pendrive não existe > > E tem sda no /dev > > Alguma sugestão? Preciso realmente montar manualmente? O ubuntu deve > conseguir montar, mas falta algo... > > Em 10/02/06, Mario Meyer < [EMAIL PROTECTED]> escreveu: > > > > 2006/2/8, Elton Lima < [EMAIL PROTECTED]>: > > > Ai tenta fazer isto: > > > > > > #sudo > > > #mount -t vfat /dev/sda /pasta desejada > > > > > > Isso talvez possa dar certo, mas antes verifica se existe o sda na > > /dev. > > > > Cuidado.. nem sempre o pendrive é /dev/sda .. eu que uso disco SATA > > por exemplo os pendrives sao sdb e as vezes sdc .. ;) > > > > []s, > > Mário Meyer > > > > -- > > ubuntu-br mailing list > > [email protected] > > www.ubuntu-br.org > > https://lists.ubuntu.com/mailman/listinfo/ubuntu-br > > > > -- ubuntu-br mailing list [email protected] www.ubuntu-br.org https://lists.ubuntu.com/mailman/listinfo/ubuntu-br
