Public bug reported:
Binary package hint: linux-image-2.6.27-9-generic
After a suspend to ram the network card a tg3 in my hp 6730b is not
working anymore.
Here is the message in dmesg after resume
[129114.112336] tg3.c:v3.94 (August 14, 2008)
[129114.124616] tg3 0000:85:00.0: enabling device (0000 -> 0002)
[129114.124649] tg3 0000:85:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[129114.124683] tg3 0000:85:00.0: setting latency timer to 64
[129114.286270] tg3: (0000:85:00.0) phy probe failed, err -19
[129114.652252] tg3: Problem fetching invariants of chip, aborting.
[129114.652339] tg3 0000:85:00.0: PCI INT A disabled
here is the content of lspci -vvvv
5:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit
Ethernet PCI Express (rev 02)
Subsystem: Hewlett-Packard Company Device 30dd
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 17
Region 0: Memory at 98600000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data <?>
Capabilities: [58] Vendor Specific Information <?>
Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: db1beffff4ffbdfc Data: effe
Capabilities: [d0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1
unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency
L0 <4us, L1 <64us
ClockPM+ Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [13c] Virtual Channel <?>
Capabilities: [160] Device Serial Number 4e-c2-b3-fe-ff-29-1f-00
Capabilities: [16c] Power Budgeting <?>
Kernel modules: tg3
Here is my kernel package:
linux-image-2.6.27-9-generic 2.6.27-9.19
After fresh boot the card is working without a problem but after a suspend to
ram then the card is not working anymore (see the the message above).
** Affects: linux (Ubuntu)
Importance: Undecided
Status: New
--
tg3 not working after s2ram on linux 2.27-9
https://bugs.launchpad.net/bugs/309485
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
