Public bug reported: I have no mouse control following sleep recovery.Unplugging and replugging my mouse usb connector does not help. However plugging into the P2S socket with an adapter does allow all mouse gestures,but unfortunately prevents power management settings to work. Bob McM
Ps I have updated to Intrepid and my mouse is a Logitech optical.Following Ardaunus instructions as best I can I include the following: Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 03:06.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 65) (prog-if 20) Subsystem: VIA Technologies, Inc. USB 2.0 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 23 Region 0: Memory at febfec00 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 03:06.2 0c03: 1106:3104 (rev 65) (prog-if 20) Subsystem: 1106:3104 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 64 bytes Interrupt: pin C routed to IRQ 23 Region 0: Memory at febfec00 (32-bit, non-prefetchable) [size=256] Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM_B2 Bank Locator: BANK3 Type: SDRAM Type Detail: None Speed: Unknown Manufacturer: Manufacturer3 Serial Number: SerNum3 Asset Tag: AssetTagNum3 Part Number: PartNum3 Handle 0x0044, DMI type 126, 19 bytes Inactive Handle 0x0045, DMI type 32, 20 bytes System Boot Information Status: No errors detected Handle 0x0046, DMI type 127, 4 bytes End Of Table Bob McM ** Affects: ubuntu Importance: Undecided Status: New -- no mouse control following sleep recovery https://bugs.launchpad.net/bugs/311705 You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. -- ubuntu-bugs mailing list ubuntu-bugs@lists.ubuntu.com https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs