You could try using the old kernel 2.6.24-23, in my case (Nokia Phone 5220) it works.
>----Messaggio originale---- >Da: [email protected] >Data: 02/04/2009 19.11 >A: <[email protected]> >Ogg: [Bug 264789] Re: USB Hard Drive Not Accessible, vol_id hangs > >How should I work around it for the moment? > >-- >USB Hard Drive Not Accessible, vol_id hangs >https://bugs.launchpad. net/bugs/264789 >You received this bug notification because you are a direct subscriber >of a duplicate bug. > >Status in The Linux Kernel: Fix Released >Status in “linux” source package in Ubuntu: Fix Released >Status in linux in Ubuntu Intrepid: Fix Committed > >Bug description: >I updated to 2.6.27-2 today, and one of my hard drives is no longer recognized. It is in a Vantec NexStar GX enclosure, and was working fine on .26, and continues to work fine on a Hardy machine. Here is the dmesg for it: > >[ 6722.944029] usb 5-5: new high speed USB device using ehci_hcd and address 27 >[ 6723.077863] usb 5-5: configuration #1 chosen from 1 choice >[ 6723.079511] hub 5-5:1.0: USB hub found >[ 6723.080345] hub 5-5:1.0: 4 ports detected >[ 6732.712034] usb 5-5: reset high speed USB device using ehci_hcd and address 27 >[ 6733.124011] usb 5- 5.1: new high speed USB device using ehci_hcd and address 28 >[ 6733.364598] usb 5-5.1: configuration #1 chosen from 1 choice >[ 6733.365180] scsi17 : SCSI emulation for USB Mass Storage devices >[ 6733.365818] usb-storage: device found at 28 >[ 6733.365830] usb-storage: waiting for device to settle before scanning >[ 6738.364276] usb-storage: device scan complete >[ 6738.361002] scsi 17:0:0:0: Direct-Access ST340063 2A 3.04 PQ: 0 ANSI: 0 >[ 6738.361002] sd 17:0:0:0: [sdm] 781422769 512-byte hardware sectors (400088 MB) >[ 6738.361002] sd 17:0:0:0: [sdm] Write Protect is off >[ 6738.361002] sd 17:0: 0:0: [sdm] Mode Sense: 03 00 00 00 >[ 6738.361002] sd 17:0:0:0: [sdm] Assuming drive cache: write through >[ 6738.361002] sd 17:0:0:0: [sdm] 781422769 512- byte hardware sectors (400088 MB) >[ 6738.370354] sd 17:0:0:0: [sdm] Write Protect is off >[ 6738.370362] sd 17:0:0:0: [sdm] Mode Sense: 03 00 00 00 >[ 6738.370365] sd 17:0:0:0: [sdm] Assuming drive cache: write through >[ 6738.371516] sdm: sdm1 >[ 6738.418089] sd 17:0:0:0: [sdm] Attached SCSI disk > [ 6738.418995] sd 17:0:0:0: Attached scsi generic sg8 type 0 >[ 6738.656598] sd 17:0:0:0: [sdm] Sense Key : No Sense [current] >[ 6738.656614] sd 17:0:0:0: [sdm] Add. Sense: No additional sense information > >>From there, the last 2 lines about Sense Key and Add Sense repeat over and over again. > >The 4 port hub that is a part of the enclosure continues to work fine though, with a floppy drive, a printer, and another hard drive. I have a Vantec NexStar 3 enclosure as well, and it is working just fine. Dmesg for the working enclosure: > >[ 4281.996024] usb 5-3: new high speed USB device using ehci_hcd and address 19 >[ 4282.131863] usb 5-3: configuration #1 chosen from 1 choice > [ 4282.133222] scsi12 : SCSI emulation for USB Mass Storage devices >[ 4282.133561] usb-storage: device found at 19 >[ 4282.133566] usb-storage: waiting for device to settle before scanning >[ 4287.132002] usb-storage: device scan complete >[ 4287.136004] scsi 12:0:0:0: Direct-Access ST375064 0AS PQ: 0 ANSI: 2 >[ 4287.138368] sd 12:0:0:0: [sdi] 1465149168 512-byte hardware sectors (750156 MB) >[ 4287.144790] sd 12:0:0:0: [sdi] Write Protect is off >[ 4287.144800] sd 12:0:0:0: [sdi] Mode Sense: 38 00 00 00 >[ 4287.144804] sd 12:0:0:0: [sdi] Assuming drive cache: write through >[ 4287.152388] sd 12:0:0:0: [sdi] 1465149168 512-byte hardware sectors (750156 MB) >[ 4287.154966] sd 12:0:0:0: [sdi] Write Protect is off >[ 4287.154975] sd 12:0:0:0: [sdi] Mode Sense: 38 00 00 00 >[ 4287.154979] sd 12:0:0:0: [sdi] Assuming drive cache: write through >[ 4287.154988] sdi: sdi1 >[ 4287.176965] sd 12:0:0:0: [sdi] Attached SCSI disk >[ 4287.177173] sd 12:0:0:0: Attached scsi generic sg7 type 0 >[ 4289.129138] kjournald starting. Commit interval 5 seconds >[ 4289.130101] EXT3 FS on sdi1, internal journal >[ 4289.130110] EXT3- fs: mounted filesystem with ordered data mode. > -- USB Hard Drive Not Accessible, vol_id hangs https://bugs.launchpad.net/bugs/264789 You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. -- ubuntu-bugs mailing list [email protected] https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
