OK, I'm not getting any visual confirmation that I've successfully
attached those two files to this bug report, so I'm just going to
include their content below...
******************
sudo lspci -vvnn :
******************
00:00.0 Host bridge [0600]: Intel Corporation Mobile 915GM/PM/GMS/910GML
Express Processor to DRAM Controller [8086:2590] (rev 04)
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile
915GM/GMS/910GML Express Graphics Controller [8086:2592] (rev 04) (prog-if 00
[VGA])
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at b0080000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 1800 [size=8]
Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at b0000000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller [0380]: Intel Corporation Mobile 915GM/GMS/910GML
Express Graphics Controller [8086:2792] (rev 04)
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Region 0: Memory at 34000000 (32-bit, non-prefetchable) [disabled]
[size=512K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) PCI Express Port 1 [8086:2660] (rev 04) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 2, PowerLimit 6.500000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable+
Address: fee0100c Data: 41b9
Capabilities: [90] Subsystem: Hewlett-Packard Company Unknown device
[103c:3081]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel
Capabilities: [180] Unknown (5)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #1 [8086:2658] (rev 04) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at 1820 [size=32]
00:1d.1 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #2 [8086:2659] (rev 04) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at 1840 [size=32]
00:1d.2 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #3 [8086:265a] (rev 04) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at 1860 [size=32]
00:1d.3 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #4 [8086:265b] (rev 04) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 22
Region 4: I/O ports at 1880 [size=32]
00:1d.7 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB2 EHCI Controller [8086:265c] (rev 04) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: Memory at b0040000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev d4) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=06, subordinate=0a, sec-latency=128
I/O behind bridge: 00003000-00003fff
Memory behind bridge: b0100000-b01fffff
Prefetchable memory behind bridge: 0000000030000000-0000000033ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Hewlett-Packard Company Unknown device
[103c:3081]
00:1e.2 Multimedia audio controller [0401]: Intel Corporation
82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller [8086:266e] (rev 04)
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 18c0 [size=64]
Region 2: Memory at b0040800 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at b0040400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.3 Modem [0703]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
AC'97 Modem Controller [8086:266d] (rev 04) (prog-if 00 [Generic])
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801FBM (ICH6M) LPC Interface
Bridge [8086:2641] (rev 04)
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) IDE Controller [8086:266f] (rev 04) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1810 [size=16]
00:1f.3 SMBus [0c05]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
SMBus Controller [8086:266a] (rev 04)
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 18a0 [size=32]
06:05.0 Network controller [0280]: Intel Corporation PRO/Wireless 2200BG
Network Connection [8086:4220] (rev 05)
Subsystem: Hewlett-Packard Company Unknown device [103c:12f5]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (750ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at b0106000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
06:06.0 CardBus bridge [0607]: Texas Instruments PCIxx21/x515 Cardbus
Controller [104c:8031]
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at b0107000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=06, secondary=07, subordinate=0a, sec-latency=176
Memory window 0: 30000000-33fff000 (prefetchable)
Memory window 1: 38000000-3bfff000
I/O window 0: 00003400-000034ff
I/O window 1: 00003800-000038ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
06:06.2 FireWire (IEEE 1394) [0c00]: Texas Instruments OHCI Compliant IEEE 1394
Host Controller [104c:8032] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 23
Region 0: Memory at b0108000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at b0100000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
06:06.3 Mass storage controller [0180]: Texas Instruments PCIxx21 Integrated
FlashMedia Controller [104c:8033]
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at b0104000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:06.4 Generic system peripheral [0805]: Texas Instruments
PCI6411/6421/6611/6621/7411/7421/7611/7621 Secure Digital Controller [104c:8034]
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (1750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at b0109000 (32-bit, non-prefetchable) [size=256]
Region 1: Memory at b0108c00 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at b0108800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
06:07.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Hewlett-Packard Company Unknown device [103c:3081]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at b0109400 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
******************
dmesg.log :
******************
[ 0.000000] Linux version 2.6.20-8-generic ([EMAIL PROTECTED]) (gcc version
4.1.2 20070129 (prerelease) (Ubuntu 4.1.1-31ubuntu2)) #2 SMP Tue Feb 13
05:18:42 UTC 2007 (Ubuntu 2.6.20-8.14-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009f800
end: 000000000009f800 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009f800 size: 0000000000000800
end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000dc000 size: 0000000000024000
end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000001f5e0000
end: 000000001f6e0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000001f6e0000 size: 000000000000b000
end: 000000001f6eb000 type: 3
[ 0.000000] copy_e820_map() start: 000000001f6eb000 size: 0000000000015000
end: 000000001f700000 type: 4
[ 0.000000] copy_e820_map() start: 000000001f700000 size: 0000000000900000
end: 0000000020000000 type: 2
[ 0.000000] copy_e820_map() start: 00000000e0000000 size: 0000000010006000
end: 00000000f0006000 type: 2
[ 0.000000] copy_e820_map() start: 00000000f0008000 size: 0000000000004000
end: 00000000f000c000 type: 2
[ 0.000000] copy_e820_map() start: 00000000fed20000 size: 0000000000070000
end: 00000000fed90000 type: 2
[ 0.000000] copy_e820_map() start: 00000000ff000000 size: 0000000001000000
end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001f6e0000 (usable)
[ 0.000000] BIOS-e820: 000000001f6e0000 - 000000001f6eb000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001f6eb000 - 000000001f700000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001f700000 - 0000000020000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 502MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 128736) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 128736
[ 0.000000] HighMem 128736 -> 128736
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 128736
[ 0.000000] On node 0 totalpages: 128736
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 973 pages used for memmap
[ 0.000000] Normal zone: 123667 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP (v000 HP ) @
0x000f76f0
[ 0.000000] ACPI: RSDT (v001 HP 09BC 0x06040000 LTP 0x00000000) @
0x1f6e5167
[ 0.000000] ACPI: FADT (v001 HP 09BC 0x06040000 LOHR 0x0000005f) @
0x1f6eae88
[ 0.000000] ACPI: MADT (v001 HP 09BC 0x06040000 LOHR 0x0000005f) @
0x1f6eaefc
[ 0.000000] ACPI: BOOT (v001 HP 09BC 0x06040000 LTP 0x00000001) @
0x1f6eafd8
[ 0.000000] ACPI: MCFG (v001 HP 09BC 0x06040000 LOHR 0x0000005f) @
0x1f6eaf9c
[ 0.000000] ACPI: SSDT (v001 HP 09BC 0x00003000 INTL 0x20030224) @
0x1f6e55c3
[ 0.000000] ACPI: SSDT (v001 HP 09BC 0x00003001 INTL 0x20030224) @
0x1f6e53eb
[ 0.000000] ACPI: SSDT (v001 HP 09BC 0x00003000 INTL 0x20030224) @
0x1f6e52d7
[ 0.000000] ACPI: SSDT (v001 HP 09BC 0x00000001 INTL 0x20030224) @
0x1f6e51ab
[ 0.000000] ACPI: DSDT (v001 HP 09BC 0x06040000 MSFT 0x0100000e) @
0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:13 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 30000000 (gap:
20000000:c0000000)
[ 0.000000] Detected 1596.622 MHz processor.
[ 14.960389] Built 1 zonelists. Total pages: 127731
[ 14.960395] Kernel command line: BOOT_IMAGE=/casper/vmlinuz
file=/cdrom/preseed/ubuntu.seed boot=casper initrd=/casper/initrd.gz quiet
splash --
[ 14.960612] mapped APIC to ffffd000 (fee00000)
[ 14.960615] mapped IOAPIC to ffffc000 (fec00000)
[ 14.960620] Enabling fast FPU save and restore... done.
[ 14.960623] Enabling unmasked SIMD FPU exception support... done.
[ 14.960634] Initializing CPU#0
[ 14.960710] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 14.962804] Console: colour VGA+ 80x25
[ 14.963024] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 14.963276] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 14.978289] Memory: 499804k/514944k available (1979k kernel code, 14732k
reserved, 882k data, 324k init, 0k highmem)
[ 14.978301] virtual kernel memory layout:
[ 14.978302] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 14.978304] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 14.978305] vmalloc : 0xe0000000 - 0xff7fe000 ( 503 MB)
[ 14.978307] lowmem : 0xc0000000 - 0xdf6e0000 ( 502 MB)
[ 14.978308] .init : 0xc03d1000 - 0xc0422000 ( 324 kB)
[ 14.978309] .data : 0xc02eecb4 - 0xc03cb6d4 ( 882 kB)
[ 14.978311] .text : 0xc0100000 - 0xc02eecb4 (1979 kB)
[ 14.978315] Checking if this processor honours the WP bit even in supervisor
mode... Ok.
[ 15.056661] Calibrating delay using timer specific routine.. 3196.55
BogoMIPS (lpj=6393104)
[ 15.056707] Security Framework v1.0.0 initialized
[ 15.056715] SELinux: Disabled at boot.
[ 15.056734] Mount-cache hash table entries: 512
[ 15.056889] CPU: After generic identify, caps: afe9fbff 00100000 00000000
00000000 00000180 00000000 00000000
[ 15.056902] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 15.056904] CPU: L2 cache: 2048K
[ 15.056908] CPU: After all inits, caps: afe9fbff 00100000 00000000 00002040
00000180 00000000 00000000
[ 15.056930] Checking 'hlt' instruction... OK.
[ 15.072754] SMP alternatives: switching to UP code
[ 15.072967] Freeing SMP alternatives: 11k freed
[ 15.073054] ACPI: Core revision 20060707
[ 15.101873] CPU0: Intel(R) Pentium(R) M processor 1.60GHz stepping 08
[ 15.101897] Total of 1 processors activated (3196.55 BogoMIPS).
[ 15.102092] ENABLING IO-APIC IRQs
[ 15.102295] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 15.248595] Brought up 1 CPUs
[ 15.248845] Booting paravirtualized kernel on bare hardware
[ 15.248917] Time: 19:26:35 Date: 01/18/107
[ 15.248946] NET: Registered protocol family 16
[ 15.249031] EISA bus registered
[ 15.249035] ACPI: bus type pci registered
[ 15.249044] PCI: Using MMCONFIG
[ 15.249735] Setting up standard PCI resources
[ 15.260472] ACPI: Interpreter enabled
[ 15.260475] ACPI: Using IOAPIC for interrupt routing
[ 15.260930] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 15.260936] PCI: Probing PCI hardware (bus 00)
[ 15.261639] Boot video device is 0000:00:02.0
[ 15.262154] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 15.262158] PCI quirk: region 1180-11bf claimed by ICH6 GPIO
[ 15.262798] PCI: Transparent bridge - 0000:00:1e.0
[ 15.262870] PCI: Bus #07 (-#0a) is hidden behind transparent bridge #06
(-#07) (try 'pci=assign-busses')
[ 15.262873] Please report the result to linux-kernel to fix this permanently
[ 15.262906] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 15.265648] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 15.266085] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 15.266675] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15)
*11
[ 15.266910] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15)
*10
[ 15.267136] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 15.267360] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15)
*10
[ 15.267585] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15)
*11
[ 15.267814] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 15.268039] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 15.268262] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 15.271441] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 15.271450] pnp: PnP ACPI init
[ 15.273622] pnp: PnP ACPI: found 8 devices
[ 15.273628] PnPBIOS: Disabled by ACPI PNP
[ 15.273671] PCI: Using ACPI for IRQ routing
[ 15.273674] PCI: If a device doesn't work, try "pci=routeirq". If it helps,
post a report
[ 15.273679] PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.0
[ 15.273735] PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.0
[ 15.273787] PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.0
[ 15.274212] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
[ 15.274220] PCI: Bridge: 0000:00:1c.0
[ 15.274221] IO window: disabled.
[ 15.274226] MEM window: disabled.
[ 15.274230] PREFETCH window: disabled.
[ 15.274239] PCI: Bus 7, cardbus bridge: 0000:06:06.0
[ 15.274241] IO window: 00003400-000034ff
[ 15.274246] IO window: 00003800-000038ff
[ 15.274252] PREFETCH window: 30000000-33ffffff
[ 15.274257] MEM window: 38000000-3bffffff
[ 15.274261] PCI: Bridge: 0000:00:1e.0
[ 15.274264] IO window: 3000-3fff
[ 15.274269] MEM window: b0100000-b01fffff
[ 15.274274] PREFETCH window: 30000000-33ffffff
[ 15.274300] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) ->
IRQ 16
[ 15.274308] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 15.274320] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 15.274336] ACPI: PCI Interrupt 0000:06:06.0[A] -> GSI 22 (level, low) ->
IRQ 17
[ 15.274343] PCI: Setting latency timer of device 0000:06:06.0 to 64
[ 15.274365] NET: Registered protocol family 2
[ 15.308570] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 15.308642] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 15.308750] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 15.308808] TCP: Hash tables configured (established 16384 bind 8192)
[ 15.308810] TCP reno registered
[ 15.320634] checking if image is initramfs... it is
[ 15.994338] Freeing initrd memory: 6636k freed
[ 15.994608] Simple Boot Flag at 0x36 set to 0x1
[ 15.994854] audit: initializing netlink socket (disabled)
[ 15.994871] audit(1171826796.088:1): initialized
[ 15.995014] VFS: Disk quotas dquot_6.5.1
[ 15.995039] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 15.995095] io scheduler noop registered
[ 15.995098] io scheduler anticipatory registered
[ 15.995100] io scheduler deadline registered
[ 15.995110] io scheduler cfq registered (default)
[ 15.995412] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 15.995461] assign_interrupt_mode Found MSI capability
[ 15.995517] Allocate Port Service[0000:00:1c.0:pcie00]
[ 15.995555] Allocate Port Service[0000:00:1c.0:pcie02]
[ 15.995586] Allocate Port Service[0000:00:1c.0:pcie03]
[ 15.995756] isapnp: Scanning for PnP cards...
[ 16.349861] isapnp: No Plug & Play device found
[ 16.375737] Real Time Clock Driver v1.12ac
[ 16.375794] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
enabled
[ 16.376451] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20 (level, low) ->
IRQ 18
[ 16.376462] ACPI: PCI interrupt for device 0000:00:1e.3 disabled
[ 16.376533] mice: PS/2 mouse device common for all mice
[ 16.377073] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024
blocksize
[ 16.377179] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 16.377184] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
[ 16.377422] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64
irq 1,12
[ 16.382618] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 16.386039] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 16.386043] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 16.386046] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 16.386048] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 16.386051] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 16.386204] EISA: Probing bus 0 at eisa.0
[ 16.386211] Cannot allocate resource for EISA slot 1
[ 16.386214] Cannot allocate resource for EISA slot 2
[ 16.386216] Cannot allocate resource for EISA slot 3
[ 16.386238] EISA: Detected 0 cards.
[ 16.416329] TCP cubic registered
[ 16.416338] NET: Registered protocol family 1
[ 16.416344] NET: Registered protocol family 8
[ 16.416346] NET: Registered protocol family 20
[ 16.416382] Using IPI No-Shortcut mode
[ 16.416450] ACPI: (supports S0 S3 S4 S5)
[ 16.416502] Magic number: 11:716:445
[ 16.416821] Freeing unused kernel memory: 324k freed
[ 16.419862] Time: tsc clocksource has been installed.
[ 16.429180] input: AT Translated Set 2 keyboard as /class/input/input0
[ 16.836195] atkbd.c: Spurious NAK on isa0060/serio0. Some program might be
trying access hardware directly.
[ 17.039854] atkbd.c: Spurious NAK on isa0060/serio0. Some program might be
trying access hardware directly.
[ 17.243868] atkbd.c: Spurious NAK on isa0060/serio0. Some program might be
trying access hardware directly.
[ 17.447637] atkbd.c: Spurious NAK on isa0060/serio0. Some program might be
trying access hardware directly.
[ 17.637479] Capability LSM initialized
[ 17.668529] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[ 2.588000] ACPI: Thermal Zone [THR0] (44 C)
[ 2.592000] Time: acpi_pm clocksource has been installed.
[ 2.592000] ACPI: Invalid passive threshold
[ 2.592000] ACPI: Thermal Zone [THR1] (36 C)
[ 2.900000] usbcore: registered new interface driver usbfs
[ 2.900000] usbcore: registered new interface driver hub
[ 2.900000] usbcore: registered new device driver usb
[ 2.904000] USB Universal Host Controller Interface driver v3.0
[ 2.904000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) ->
IRQ 19
[ 2.904000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 2.904000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.904000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus
number 1
[ 2.904000] uhci_hcd 0000:00:1d.0: irq 19, io base 0x00001820
[ 2.904000] usb usb1: configuration #1 chosen from 1 choice
[ 2.904000] hub 1-0:1.0: USB hub found
[ 2.904000] hub 1-0:1.0: 2 ports detected
[ 2.988000] ieee1394: Initialized config rom entry `ip1394'
[ 3.008000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) ->
IRQ 20
[ 3.008000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 3.008000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.008000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus
number 2
[ 3.008000] uhci_hcd 0000:00:1d.1: irq 20, io base 0x00001840
[ 3.008000] usb usb2: configuration #1 chosen from 1 choice
[ 3.008000] hub 2-0:1.0: USB hub found
[ 3.008000] hub 2-0:1.0: 2 ports detected
[ 3.028000] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 3.112000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) ->
IRQ 21
[ 3.112000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 3.112000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.112000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus
number 3
[ 3.112000] uhci_hcd 0000:00:1d.2: irq 21, io base 0x00001860
[ 3.112000] usb usb3: configuration #1 chosen from 1 choice
[ 3.112000] hub 3-0:1.0: USB hub found
[ 3.112000] hub 3-0:1.0: 2 ports detected
[ 3.216000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) ->
IRQ 22
[ 3.216000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 3.216000] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 3.216000] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus
number 4
[ 3.216000] uhci_hcd 0000:00:1d.3: irq 22, io base 0x00001880
[ 3.216000] usb usb4: configuration #1 chosen from 1 choice
[ 3.216000] hub 4-0:1.0: USB hub found
[ 3.216000] hub 4-0:1.0: 2 ports detected
[ 3.320000] ACPI: PCI Interrupt 0000:06:06.2[C] -> GSI 21 (level, low) ->
IRQ 23
[ 3.372000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) ->
IRQ 19
[ 3.372000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 3.372000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.372000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus
number 5
[ 3.372000] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.372000] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[ 3.372000] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xb0040000
[ 3.376000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec
2004
[ 3.376000] usb usb5: configuration #1 chosen from 1 choice
[ 3.376000] hub 5-0:1.0: USB hub found
[ 3.376000] hub 5-0:1.0: 8 ports detected
[ 3.376000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[23]
MMIO=[b0108000-b01087ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 3.480000] 8139cp 0000:06:07.0: This (id 10ec:8139 rev 10) is not an 8139C+
compatible chip
[ 3.480000] 8139cp 0000:06:07.0: Try the "8139too" driver instead.
[ 3.480000] 8139too Fast Ethernet driver 0.9.28
[ 3.480000] ACPI: PCI Interrupt 0000:06:07.0[A] -> GSI 20 (level, low) ->
IRQ 18
[ 3.480000] eth0: RealTek RTL8139 at 0xe0074400, 00:0a:e4:d3:a5:96, IRQ 18
[ 3.480000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 3.484000] ICH6: IDE controller at PCI slot 0000:00:1f.1
[ 3.484000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) ->
IRQ 21
[ 3.484000] ICH6: chipset revision 4
[ 3.484000] ICH6: not 100% native mode: will probe irqs later
[ 3.484000] ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA,
hdb:DMA
[ 3.484000] Probing IDE interface ide0...
[ 3.772000] hda: FUJITSU MHT2060AT PL, ATA DISK drive
[ 4.556000] hdb: HL-DT-ST DVD-RW GCA-4080N, ATAPI CD/DVD-ROM drive
[ 4.612000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 4.620000] SCSI subsystem initialized
[ 4.624000] libata version 2.00 loaded.
[ 4.636000] hda: max request size: 128KiB
[ 4.648000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[05e40a00a7055026]
[ 4.712000] hda: 117210240 sectors (60011 MB) w/8192KiB Cache,
CHS=65535/16/63, UDMA(100)
[ 4.712000] hda: cache flushes supported
[ 4.712000] hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
[ 4.788000] hdb: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, DMA
[ 4.788000] Uniform CD-ROM driver Revision: 3.20
[ 5.752000] kjournald starting. Commit interval 5 seconds
[ 5.752000] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.776000] kjournald starting. Commit interval 5 seconds
[ 5.776000] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.816000] kjournald starting. Commit interval 5 seconds
[ 5.816000] EXT3-fs: mounted filesystem with ordered data mode.
[ 6.368000] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 6.412000] ISO 9660 Extensions: RRIP_1991A
[ 6.460000] Registering unionfs 20060916-2203
[ 6.460000] unionfs: debugging is not enabled
[ 6.468000] loop: loaded (max 8 devices)
[ 6.620000] squashfs: version 3.1 (2006/08/19) Phillip Lougher
[ 119.048000] eth0: link up, 10Mbps, full-duplex, lpa 0x4441
[ 119.404000] iTCO_vendor_support: vendor-support=0
[ 119.716000] ieee80211_crypt: registered algorithm 'NULL'
[ 120.596000] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 120.596000] ieee80211: Copyright (C) 2004-2005 Intel Corporation <[EMAIL
PROTECTED]>
[ 121.240000] Linux agpgart interface v0.101 (c) Dave Jones
[ 121.644000] sdhci: Secure Digital Host Controller Interface driver, 0.12
[ 121.644000] sdhci: Copyright(c) Pierre Ossman
[ 121.644000] sdhci: SDHCI controller found at 0000:06:06.4 [104c:8034] (rev 0)
[ 121.644000] ACPI: PCI Interrupt 0000:06:06.4[A] -> GSI 22 (level, low) ->
IRQ 17
[ 121.644000] mmc0: SDHCI at 0xb0109000 irq 17 DMA
[ 121.648000] mmc1: SDHCI at 0xb0108c00 irq 17 DMA
[ 121.652000] mmc2: SDHCI at 0xb0108800 irq 17 DMA
[ 121.984000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
[ 121.984000] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[ 121.984000] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 122.524000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 122.528000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 122.592000] Yenta: CardBus bridge found at 0000:06:06.0 [103c:3081]
[ 122.592000] Yenta: Enabling burst memory read transactions
[ 122.592000] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 122.592000] Yenta: Routing CardBus interrupts to PCI
[ 122.592000] Yenta TI: socket 0000:06:06.0, mfunc 0x01aa1b02, devctl 0x64
[ 122.732000] NET: Registered protocol family 17
[ 122.824000] Yenta: ISA IRQ mask 0x0cf8, PCI irq 17
[ 122.824000] Socket status: 30000006
[ 122.824000] Yenta: Raising subordinate bus# of parent bus (#06) from #07 to
#0a
[ 122.824000] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
[ 122.824000] cs: IO port probe 0x3000-0x3fff: clean.
[ 122.824000] pcmcia: parent PCI bridge Memory window: 0xb0100000 - 0xb01fffff
[ 122.824000] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x33ffffff
[ 122.876000] agpgart: Detected an Intel 915GM Chipset.
[ 122.876000] agpgart: Detected 7932K stolen memory.
[ 122.896000] agpgart: AGP aperture is 256M @ 0xc0000000
[ 123.060000] ACPI: PCI Interrupt 0000:06:06.3[A] -> GSI 22 (level, low) ->
IRQ 17
[ 123.260000] atkbd.c: Spurious NAK on isa0060/serio0. Some program might be
trying access hardware directly.
[ 123.460000] atkbd.c: Spurious NAK on isa0060/serio0. Some program might be
trying access hardware directly.
[ 123.496000] intel_rng: FWH not detected
[ 123.808000] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver,
1.2.0kmprq
[ 123.808000] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 123.808000] ACPI: PCI Interrupt 0000:06:05.0[A] -> GSI 20 (level, low) ->
IRQ 18
[ 123.808000] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 123.932000] input: PS/2 Mouse as /class/input/input1
[ 123.952000] input: AlpsPS/2 ALPS GlidePoint as /class/input/input2
[ 124.776000] ipw2200: Radio Frequency Kill Switch is On:
[ 124.776000] Kill switch must be turned off for wireless networking to work.
[ 124.776000] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a
channels)
[ 124.776000] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) ->
IRQ 16
[ 124.776000] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 125.524000] cs: IO port probe 0x100-0x3af: excluding 0x200-0x20f
[ 125.524000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 125.524000] cs: IO port probe 0x820-0x8ff: clean.
[ 125.524000] cs: IO port probe 0xc00-0xcf7: clean.
[ 125.524000] cs: IO port probe 0xa00-0xaff: clean.
[ 125.600000] intel8x0_measure_ac97_clock: measured 55451 usecs
[ 125.600000] intel8x0: clocking to 48000
[ 126.972000] fuse init (API version 7.8)
[ 128.296000] NET: Registered protocol family 10
[ 128.296000] lo: Disabled Privacy Extensions
[ 128.296000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 137.720000] ACPI: AC Adapter [AC] (on-line)
[ 137.904000] ACPI: Battery Slot [BAT0] (battery present)
[ 137.988000] input: Power Button (FF) as /class/input/input3
[ 138.016000] ACPI: Power Button (FF) [PWRF]
[ 138.080000] input: Lid Switch as /class/input/input4
[ 138.108000] ACPI: Lid Switch [LID0]
[ 138.164000] input: Sleep Button (CM) as /class/input/input5
[ 138.164000] ACPI: Sleep Button (CM) [SLPB]
[ 138.188000] input: Power Button (CM) as /class/input/input6
[ 138.188000] ACPI: Power Button (CM) [PWB]
[ 138.320000] eth0: no IPv6 routers present
[ 138.332000] No dock devices found.
[ 138.352000] Using specific hotkey driver
[ 138.396000] ibm_acpi: ec object not found
[ 138.488000] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 144.844000] lp: driver loaded but no devices found
[ 145.024000] ppdev: user-space parallel port driver
[ 149.220000] [drm] Initialized drm 1.1.0 20060810
[ 149.252000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) ->
IRQ 22
[ 149.252000] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 158.584000] apm: BIOS not found.
[ 189.228000] Bluetooth: Core ver 2.11
[ 189.228000] NET: Registered protocol family 31
[ 189.228000] Bluetooth: HCI device and connection manager initialized
[ 189.228000] Bluetooth: HCI socket layer initialized
[ 189.908000] Bluetooth: L2CAP ver 2.8
[ 189.908000] Bluetooth: L2CAP socket layer initialized
[ 192.000000] Bluetooth: RFCOMM socket layer initialized
[ 192.000000] Bluetooth: RFCOMM TTY layer initialized
[ 192.000000] Bluetooth: RFCOMM ver 1.8
[ 194.404000] eth0: no IPv6 routers present
--
ACPI regression: HP dv4000 / dv4150 laptop
https://launchpad.net/bugs/85838
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
