Public bug reported:
Binary package hint: linux-image-2.6.24-28-generic
When a 2T Hitachi HDS722020ALA330 disk is attached to Silicon Image
PCI-E sil3132 controller partition table is overwritten with zeroes
(verified by reading disk attached to a different controller) at every
boot. 750G WD WD7501AALS-0 disk attached to the same controller works
fine, and until recently this controller worked with two 750G disks
forming a part of md RAID, 2T disks also works fine when attached to
motherboard SATA. Tried two sil3132-based controllers by different
manufacturers and at least two 2T Hitachi disks - problem persists. Logs
are not clean, but I see nothing too suspicious - INIT_DEV_PARAMS fails
on both disks, spurious interrupt seems to clear itself and as for HPA
resize, I get this message on all 2T disks including those attached to
the motherboard SATA and functioning normally - I kept this part of the
log after the blank line.
[ 98.974414] sata_sil24 0000:02:00.0: version 1.1
[ 98.974694] ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
[ 98.974701] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC5] -> GSI 16
(level, low) -> IRQ 16
[ 98.975060] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 98.977005] scsi0 : sata_sil24
[ 98.978616] scsi1 : sata_sil24
[ 98.978648] ata1: SATA max UDMA/100 host m...@0xf4004000 port 0xf4000000 irq
16
[ 98.978652] ata2: SATA max UDMA/100 host m...@0xf4004000 port 0xf4002000 irq
16
[ 101.157874] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 101.164612] ata1.00: failed to IDENTIFY (INIT_DEV_PARAMS failed,
err_mask=0x80)
[ 101.164615] ata1: failed to recover some devices, retrying in 5 secs
[ 101.178227] ata1: spurious interrupt (slot_stat 0x0 active_tag -84148995
sactive 0x0)
[ 108.361296] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 108.383107] ata1.00: failed to set max address (err_mask=0x1)
[ 108.383111] ata1.00: device aborted resize (3907029168 ->
18446744073321613488), skipping HPA handling
[ 108.383117] ata1.00: ATA-8: Hitachi HDS722020ALA330, JKAOA20N, max UDMA/133
[ 108.383119] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 108.384679] ata1.00: configured for UDMA/100
[ 110.564219] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 110.574722] ata2.00: failed to IDENTIFY (INIT_DEV_PARAMS failed,
err_mask=0x80)
[ 110.574724] ata2: failed to recover some devices, retrying in 5 secs
[ 117.773640] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 0)
[ 117.798669] ata2.00: ATA-8: WDC WD7501AALS-00J7B0, 05.00K05, max UDMA/133
[ 117.798672] ata2.00: 1465149168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 117.799477] ata2.00: configured for UDMA/100
[ 117.799489] ata2: exception Emask 0x1 SAct 0x0 SErr 0x0 action 0x0 t4
[ 117.799492] ata2: irq_stat 0x00020002, device error via D2H FIS
[ 117.800875] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS72202 JKAO
PQ: 0 ANSI: 5
[ 117.800978] sd 0:0:0:0: [sde] 3907029168 512-byte hardware sectors (2000399
MB)
[ 117.800995] sd 0:0:0:0: [sde] Write Protect is off
[ 117.800997] sd 0:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 117.801022] sd 0:0:0:0: [sde] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 117.801104] sd 0:0:0:0: [sde] 3907029168 512-byte hardware sectors (2000399
MB)
[ 117.801121] sd 0:0:0:0: [sde] Write Protect is off
[ 117.801123] sd 0:0:0:0: [sde] Mode Sense: 00 3a 00 00
[ 117.801145] sd 0:0:0:0: [sde] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 117.801149] sde: unknown partition table
[ 117.804795] sd 0:0:0:0: [sde] Attached SCSI disk
[ 117.804841] sd 0:0:0:0: Attached scsi generic sg4 type 0
[ 117.805381] scsi 1:0:0:0: Direct-Access ATA WDC WD7501AALS-0 05.0
PQ: 0 ANSI: 5
[ 117.805763] sd 1:0:0:0: [sdf] 1465149168 512-byte hardware sectors (750156
MB)
[ 117.805777] sd 1:0:0:0: [sdf] Write Protect is off
[ 117.805778] sd 1:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 117.805800] sd 1:0:0:0: [sdf] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 117.805847] sd 1:0:0:0: [sdf] 1465149168 512-byte hardware sectors (750156
MB)
[ 117.805859] sd 1:0:0:0: [sdf] Write Protect is off
[ 117.805861] sd 1:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 117.805880] sd 1:0:0:0: [sdf] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 117.805884] sdf: sdf1
[ 117.811758] sd 1:0:0:0: [sdf] Attached SCSI disk
[ 117.811789] sd 1:0:0:0: Attached scsi generic sg5 type 0
[ 117.823613] scsi3 : sata_nv
[ 117.826809] scsi4 : sata_nv
[ 117.827011] ata3: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xcc00 irq 20
[ 117.827015] ata4: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xcc08 irq 20
[ 118.296382] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 118.304866] ata3.00: failed to set max address (err_mask=0x1)
[ 118.304869] ata3.00: device aborted resize (3907029168 ->
18446744073321613488), skipping HPA handling
[ 118.304873] ata3.00: ATA-8: Hitachi HDS722020ALA330, JKAOA20N, max UDMA/133
[ 118.304876] ata3.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 118.320459] ata3.00: configured for UDMA/133
[ 118.793387] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 118.800629] ata4.00: failed to set max address (err_mask=0x1)
[ 118.800633] ata4.00: device aborted resize (3907029168 ->
18446744073321613488), skipping HPA handling
[ 118.800638] ata4.00: ATA-8: Hitachi HDS722020ALA330, JKAOA20N, max UDMA/133
[ 118.800640] ata4.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 118.816212] ata4.00: configured for UDMA/133
[ 118.816322] scsi 3:0:0:0: Direct-Access ATA Hitachi HDS72202 JKAO
PQ: 0 ANSI: 5
[ 118.816409] sd 3:0:0:0: [sdg] 3907029168 512-byte hardware sectors (2000399
MB)
[ 118.816423] sd 3:0:0:0: [sdg] Write Protect is off
[ 118.816425] sd 3:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 118.816445] sd 3:0:0:0: [sdg] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 118.816504] sd 3:0:0:0: [sdg] 3907029168 512-byte hardware sectors (2000399
MB)
[ 118.816515] sd 3:0:0:0: [sdg] Write Protect is off
[ 118.816517] sd 3:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 118.816537] sd 3:0:0:0: [sdg] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 118.816541] sdg: sdg1
[ 118.822188] sd 3:0:0:0: [sdg] Attached SCSI disk
[ 118.822234] sd 3:0:0:0: Attached scsi generic sg6 type 0
[ 118.822310] scsi 4:0:0:0: Direct-Access ATA Hitachi HDS72202 JKAO
PQ: 0 ANSI: 5
[ 118.822383] sd 4:0:0:0: [sdh] 3907029168 512-byte hardware sectors (2000399
MB)
[ 118.822396] sd 4:0:0:0: [sdh] Write Protect is off
[ 118.822398] sd 4:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 118.822420] sd 4:0:0:0: [sdh] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 118.822465] sd 4:0:0:0: [sdh] 3907029168 512-byte hardware sectors (2000399
MB)
[ 118.822479] sd 4:0:0:0: [sdh] Write Protect is off
[ 118.822481] sd 4:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 118.822504] sd 4:0:0:0: [sdh] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 118.822508] sdh: sdh1
[ 118.834101] sd 4:0:0:0: [sdh] Attached SCSI disk
[ 118.834133] sd 4:0:0:0: Attached scsi generic sg7 type 0
8.04 server Linux server.lvm.pvt 2.6.24-28-generic #1 SMP Wed Nov 24 09:00:20
UTC 2010 x86_64 GNU/Linux, motherboard is Gigabyte GA-M61P-S3, nforce 430.
** Affects: linux (Ubuntu)
Importance: Undecided
Status: New
--
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
https://bugs.launchpad.net/bugs/700674
Title:
partition table destroyed on large sata disk attached to sil3132 controller
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
