Public bug reported:
Using the alip 04072011 image and omap3-x11 hwpack from the same date
the system fails to boot. Here is a boot log:
Texas Instruments X-Loader 1.4.2 (Feb 19 2009 - 12:01:24)
Reading boot sector
Loading u-boot.bin from mmc
U-Boot 2011.03-rc1 (Feb 09 2011 - 01:33:04)
OMAP3530-GP ES3.1, CPU-OPP2, L3-165MHz, Max CPU Clock 720 mHz
OMAP3 Beagle board + LPDDR/NAND
I2C: ready
DRAM: 256 MiB
NAND: 256 MiB
MMC: OMAP SD/MMC: 0
In: serial
Out: serial
Err: serial
Beagle Rev C4
timed out in wait_for_pin: I2C_STAT=0
No EEPROM on expansion board
Die ID #478800040000000004037f680d01f01a
Hit any key to stop autoboot: 0
reading boot.scr
379 bytes read
Running bootscript from mmc ...
## Executing script at 82000000
reading uImage
4004976 bytes read
reading uInitrd
3997273 bytes read
## Booting kernel from Legacy Image at 80000000 ...
Image Name: Linux
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4004912 Bytes = 3.8 MiB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
Image Name: initramfs
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 3997209 Bytes = 3.8 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.38-1001-linaro-omap (buildd@genip) (gcc
version 4.)
[ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=50c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction
cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Reserving 12582912 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c09a2000 s9600 r8192 d14976 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages:2
[ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8
root=UUID=0
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] allocated 1310720 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want
memory cs
[ 0.000000] Memory: 244MB = 244MB total
[ 0.000000] Memory: 234576k/234576k available, 27568k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf800000 - 0xc0000000 ( 8 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0051000 ( 292 kB)
[ 0.000000] .text : 0xc0051000 - 0xc066baa0 (6251 kB)
[ 0.000000] .data : 0xc066c000 - 0xc06d3f50 ( 416 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1,
Node1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:402
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
[ 0.000000] Reprogramming SDRC clock to 332000000 Hz
[ 0.000000] GPMC revision 5.0
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96
interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every
13107s
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.38-1001-linaro-omap (buildd@genip) (gcc
version 4.)
[ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=50c53c7f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction
cache
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] Machine: OMAP3 Beagle Board
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Reserving 12582912 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c09a2000 s9600 r8192 d14976 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages:2
[ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8
root=UUID=0
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] allocated 1310720 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want
memory cs
[ 0.000000] Memory: 244MB = 244MB total
[ 0.000000] Memory: 234576k/234576k available, 27568k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf800000 - 0xc0000000 ( 8 MB)
[ 0.000000] .init : 0xc0008000 - 0xc0051000 ( 292 kB)
[ 0.000000] .text : 0xc0051000 - 0xc066baa0 (6251 kB)
[ 0.000000] .data : 0xc066c000 - 0xc06d3f50 ( 416 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1,
Node1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:402
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
[ 0.000000] Reprogramming SDRC clock to 332000000 Hz
[ 0.000000] GPMC revision 5.0
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96
interrupts
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every
13107s
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.291900] Calibrating delay loop... 522.02 BogoMIPS (lpj=2039808)
[ 0.468444] pid_max: default: 32768 minimum: 301
[ 0.473480] Security Framework initialized
[ 0.477905] AppArmor: AppArmor initialized
[ 0.482238] Yama: becoming mindful.
[ 0.486267] Mount-cache hash table entries: 512
[ 0.491882] Initializing cgroup subsys ns
[ 0.496124] ns_cgroup deprecated: consider using the 'clone_children' flag
witho.
[ 0.505432] Initializing cgroup subsys cpuacct
[ 0.510162] Initializing cgroup subsys memory
[ 0.514831] Initializing cgroup subsys devices
[ 0.519531] Initializing cgroup subsys freezer
[ 0.524353] CPU: Testing write buffer coherency: ok
[ 0.529785] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5
counters ae
[ 0.539337] Brought up 1 CPUs
[ 0.542510] SMP: Total of 1 processors activated (522.02 BogoMIPS).
[ 0.549682] devtmpfs: initialized
[ 0.557830] print_constraints: dummy:
[ 0.562133] NET: Registered protocol family 16
[ 0.568481] omap_device: omap_gpio.0: new worst case activate latency 0:
30517
[ 0.576171] OMAP GPIO hardware version 2.5
[ 0.580627] OMAP GPIO hardware version 2.5
[ 0.585052] OMAP GPIO hardware version 2.5
[ 0.589508] OMAP GPIO hardware version 2.5
[ 0.593963] OMAP GPIO hardware version 2.5
[ 0.598388] OMAP GPIO hardware version 2.5
[ 0.604370] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.611541] OMAP3 Beagle Rev: C4
[ 0.616027] omap_device: omap_dss: clk_add_alias for tv_clk failed
[ 0.622558] omap_device: omap_dss: clk_add_alias for video_clk failed
[ 0.629364] omap_device: omap_dss: clk_add_alias for sys_clk failed
[ 0.636901] omap_device: omap_uart.0: new worst case activate latency 0:
30517
[ 0.637207] omap_device: omap_uart.0: new worst case deactivate latency 0:
30517
[ 0.655700] Found NAND on CS0
[ 0.658843] Registering NAND on CS0
[ 0.663024] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.674133] OMAP DMA hardware revision 4.0
[ 0.688385] bio: create slab <bio-0> at 0
[ 0.695465] SCSI subsystem initialized
[ 0.700317] usbcore: registered new interface driver usbfs
[ 0.706268] usbcore: registered new interface driver hub
[ 0.712097] usbcore: registered new device driver usb
[ 0.726928] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz
[ 0.735931] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 0.741455] twl4030: power (irq 373) chaining IRQs 376..383
[ 0.747955] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 0.756591] print_constraints: VUSB1V5: 1500 mV normal standby
[ 0.763336] print_constraints: VUSB1V8: 1800 mV normal standby
[ 0.770080] print_constraints: VUSB3V1: 3100 mV normal standby
[ 0.777740] print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal
standby
[ 0.786193] print_constraints: VDAC: 1800 mV normal standby
[ 0.792694] print_constraints: VPLL2: 1800 mV normal standby
[ 0.799407] print_constraints: VSIM: 1800 <--> 3000 mV at 1800 mV normal
standby
[ 0.816711] omap_i2c omap_i2c.3: bus 3 rev3.12 at 100 kHz
[ 0.823791] Advanced Linux Sound Architecture Driver Version 1.0.23.
[ 0.831390] NetLabel: Initializing
[ 0.835052] NetLabel: domain hash size = 128
[ 0.839630] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.844940] NetLabel: unlabeled traffic allowed by default
[ 0.854034] DMA-API: preallocated 4096 debug entries
[ 0.859344] DMA-API: debugging enabled by kernel config
[ 0.864868] Switching to clocksource 32k_counter
[ 0.874053] Switched to NOHz mode on CPU #0
[ 0.890472] AppArmor: AppArmor Filesystem Enabled
[ 0.915130] NET: Registered protocol family 2
[ 0.920227] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.928833] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.936492] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.943481] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.950164] TCP reno registered
[ 0.953521] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.959716] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.966766] NET: Registered protocol family 1
[ 0.972106] RPC: Registered udp transport module.
[ 0.977081] RPC: Registered tcp transport module.
[ 0.982086] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.989410] Trying to unpack rootfs image as initramfs...
[ 1.014190] PMU: registered new PMU device of type 0
[ 1.026947] omap_sr_disable: omap_sr struct for sr_mpu not found
[ 1.033264] omap_voltage_scale_vdd: No voltage scale API registered for
vdd_mpu
[ 1.040985] omap_dvfs_voltage_scale: Unable to scale the mpu to 1350000 volt
[ 1.048400] omap_sr_enable: omap_sr struct for sr_mpu not found
[ 1.082397] omap_sr_disable: omap_sr struct for sr_mpu not found
[ 1.088714] omap_voltage_scale_vdd: No voltage scale API registered for
vdd_mpu
[ 1.096435] omap_dvfs_voltage_scale: Unable to scale the mpu to 1350000 volt
[ 1.103790] omap_sr_enable: omap_sr struct for sr_mpu not found
[ 1.137145] audit: initializing netlink socket (disabled)
[ 1.142883] type=2000 audit(0.835:1): initialized
[ 1.191955] VFS: Disk quotas dquot_6.5.2
[ 1.196685] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.223022] fuse init (API version 7.16)
[ 1.229309] Btrfs loaded
[ 1.245697] msgmni has been set to 458
[ 1.263214] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
253)
[ 1.271057] io scheduler noop registered
[ 1.275207] io scheduler deadline registered
[ 1.292785] io scheduler cfq registered (default)
[ 1.356750] OMAP DSS rev 2.0
[ 1.683837] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.695526] Freeing initrd memory: 3900K
[ 1.701690] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
[ 1.709594] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
[ 1.717407] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
[ 1.724853] console [ttyO2] enabled, bootconsole disabled
[ 1.724853] console [ttyO2] enabled, bootconsole disabled
[ 1.748870] brd: module loaded
[ 1.758270] loop: module loaded
[ 1.762451] omap_device: omap_i2c.1: new worst case activate latency 0: 30517
[ 1.770629] i2c-core: driver [adp5520] using legacy suspend method
[ 1.777221] i2c-core: driver [adp5520] using legacy resume method
[ 1.785125] omap2-nand driver initializing
[ 1.789825] ONFI flash detected
[ 1.793701] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND
256Mi)
[ 1.802917] Creating 5 MTD partitions on "omap2-nand.0":
[ 1.808593] 0x000000000000-0x000000080000 : "X-Loader"
[ 1.816162] 0x000000080000-0x000000260000 : "U-Boot"
[ 1.824005] 0x000000260000-0x000000280000 : "U-Boot Env"
[ 1.831420] 0x000000280000-0x000000680000 : "Kernel"
[ 1.840179] 0x000000680000-0x000010000000 : "File System"
[ 1.960266] PPP generic driver version 2.4.2
[ 1.965270] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256)
(6 b.
[ 1.975555] CSLIP: code copyright 1989 Regents of the University of
California.
[ 1.983337] SLIP linefill/keepalive option.
[ 1.988067] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.010894] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 4.016967] ehci-omap ehci-omap.0: new USB bus registered, assigned bus
number 1
[ 4.025054] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 4.042175] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 4.049285] hub 1-0:1.0: USB hub found
[ 4.053344] hub 1-0:1.0: 3 ports detected
[ 4.089508] udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma)
[ 4.097259] mousedev: PS/2 mouse device common for all mice
[ 4.104278] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 4.111389] twl_rtc twl_rtc: Enabling TWL-RTC.
[ 4.388000] usb 1-2: new high speed USB device using ehci-omap and address 2
[ 4.551391] hub 1-2:1.0: USB hub found
[ 4.555633] hub 1-2:1.0: 4 ports detected
[ 4.848510] usb 1-2.4: new high speed USB device using ehci-omap and address
3
[ 5.113830] omap_i2c omap_i2c.1: controller timed out
[ 5.119262] omap_device: omap_i2c.1: new worst case deactivate latency 0:
30517
[ 5.127044] twl: i2c_read failed to transfer all messages
[ 5.132812] twl_rtc: Could not read TWLregister F - error -110
[ 6.143707] omap_i2c omap_i2c.1: controller timed out waiting for start
conditioh
[ 6.152618] twl: i2c_write failed to transfer all messages
[ 6.158416] twl4030: twl4030_sih_do_mask, write --> -110
[ 6.164398] twl_rtc: probe of twl_rtc failed with error -110
[ 6.171417] device-mapper: uevent: version 1.0.3
[ 6.177185] device-mapper: ioctl: 4.19.1-ioctl (2011-01-07) initialised:
dm-devem
[ 6.186614] device-mapper: multipath: version 1.2.0 loaded
[ 6.192718] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 6.200347] omap_sr_disable: omap_sr struct for sr_mpu not found
[ 6.206787] omap_voltage_scale_vdd: No voltage scale API registered for
vdd_mpu
[ 6.214569] omap_dvfs_voltage_scale: Unable to scale the mpu to 1350000 volt
[ 6.222045] omap_sr_enable: omap_sr struct for sr_mpu not found
[ 6.228637] cpuidle: using governor ladder
[ 6.233062] cpuidle: using governor menu
[ 6.237365] sdhci: Secure Digital Host Controller Interface driver
[ 6.243896] sdhci: Copyright(c) Pierre Ossman
[ 7.245635] omap_i2c omap_i2c.1: controller timed out
[ 7.260955] twl: i2c_read failed to transfer all messages
[ 7.266693] mmci-omap-hs: probe of mmci-omap-hs.0 failed with error -110
[ 7.275512] OMAP3 Beagle/Devkit8000 SoC init
[ 8.276855] omap_i2c omap_i2c.1: controller timed out
[ 8.292205] twl: i2c_read failed to transfer all messages
[ 9.299926] omap_i2c omap_i2c.1: controller timed out waiting for start
conditioh
[ 9.308837] twl: i2c_write failed to transfer all messages
[ 10.315765] omap_i2c omap_i2c.1: controller timed out waiting for start
conditioh
[ 10.324645] twl: i2c_write failed to transfer all messages
[ 11.331207] omap_i2c omap_i2c.1: controller timed out waiting for start
conditioh
[ 11.340118] twl: i2c_write failed to transfer all messages
[ 12.339355] omap_i2c omap_i2c.1: controller timed out
[ 12.354705] twl: i2c_read failed to transfer all messages
[ 13.362426] omap_i2c omap_i2c.1: controller timed out waiting for start
conditioh
[ 13.371337] twl: i2c_write failed to transfer all messages
[ 14.378082] omap_i2c omap_i2c.1: controller timed out waiting for start
conditioh
[ 14.386962] twl: i2c_write failed to transfer all messages
[ 15.418182] omap_i2c omap_i2c.1: controller timed out
[ 15.423583] twl: i2c_read failed to transfer all messages
[ 16.424987] omap_i2c omap_i2c.1: controller timed out
[ 16.440643] twl: i2c_read failed to transfer all messages
[ 17.448394] omap_i2c omap_i2c.1: controller timed out waiting for start
conditioh
[ 17.457275] twl: i2c_write failed to transfer all messages
[ 17.469665] asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok
[ 17.477081] ALSA device list:
[ 17.480285] #0: omap3beagle
[ 17.485382] TCP cubic registered
[ 17.490264] NET: Registered protocol family 10
[ 17.498962] NET: Registered protocol family 17
[ 17.504058] Registering the dns_resolver key type
[ 17.509063] VFP support v0.3: implementor 41 architecture 3 part 30 variant
c re1
[ 17.517333] ThumbEE CPU extension supported.
[ 18.520111] omap_i2c omap_i2c.1: controller timed out
[ 18.525543] twl: i2c_read failed to transfer all messages
[ 18.531311] omap3_twl_set_sr_bit: Error access to TWL4030 (-110)
[ 18.539489] Power Management for TI OMAP3.
[ 18.544769] sr_init: No PMIC hook to init smartreflex
[ 18.550384] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver
initiald
[ 18.558868] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver
initiald
[ 18.567474] SmartReflex Class3 initialized
[ 18.580841] clock: disabling unused clocks to save power
[ 18.588134] registered taskstats version 1
[ 18.592834] fbcvt: 1280x720@60: CVT Name - .921M9-R
[ 18.625579] Console: switching to colour frame buffer device 160x45
[ 19.645202] omap_i2c omap_i2c.1: controller timed out
[ 19.659484] twl: i2c_read failed to transfer all messages
[ 19.665344] _regulator_enable: VPLL2: is_enabled() failed: -110
[ 19.671813] omapfb omapfb: Failed to enable display 'dvi'
[ 19.678405] omapfb omapfb: failed to setup omapfb
[ 19.683380] Division by zero in kernel.
[ 19.683441] [<c005af11>] (unwind_backtrace+0x1/0x9c) from [<c02871a3>]
(Ldiv0+0x)
[ 19.683532] Division by zero in kernel.
[ 19.683563] [<c005af11>] (unwind_backtrace+0x1/0x9c) from [<c02871a3>]
(Ldiv0+0x)
[ 19.683776] Division by zero in kernel.
[ 19.683807] [<c005af11>] (unwind_backtrace+0x1/0x9c) from [<c02871a3>]
(Ldiv0+0x)
[ 19.687866] Division by zero in kernel.
[ 19.687896] [<c005af11>] (unwind_backtrace+0x1/0x9c) from [<c02871a3>]
(Ldiv0+0x)
[ 19.687957] Division by zero in kernel.
[ 19.687988] [<c005af11>] (unwind_backtrace+0x1/0x9c) from [<c02871a3>]
(Ldiv0+0x)
** Affects: linux-linaro-omap (Ubuntu)
Importance: Undecided
Status: New
--
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
https://bugs.launchpad.net/bugs/754007
Title:
omapfb fails on beagle C4
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
