With the beta 2 developer image, and hwpack_linaro- omap3-x11-base_20110426-0 beagle C4 fails to boot.
Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.38-1002-linaro-omap (buildd@araceae) (gcc version 4.5) [ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=50c53c7f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: OMAP3 Beagle Board, model: TI OMAP3 BeagleBoard [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Reserving 12582912 bytes SDRAM for VRAM [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp ) [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz [ 0.000000] Reprogramming SDRC clock to 332000000 Hz [ 0.000000] PERCPU: Embedded 8 pages/cpu @c09c6000 s9888 r8192 d14688 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 612 [ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8 root=UUID=7c80 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] allocated 1310720 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgros [ 0.000000] Memory: 244MB = 244MB total [ 0.000000] Memory: 234688k/234688k available, 27456k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf800000 - 0xc0000000 ( 8 MB) [ 0.000000] .init : 0xc0008000 - 0xc0052000 ( 296 kB) [ 0.000000] .text : 0xc0052000 - 0xc0687760 (6358 kB) [ 0.000000] .data : 0xc0688000 - 0xc06f5800 ( 438 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU-based detection of stalled CPUs is disabled. [ 0.000000] NR_IRQS:410 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck. [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 13107199s [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.38-1002-linaro-omap (buildd@araceae) (gcc version 4.5) [ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=50c53c7f [ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine: OMAP3 Beagle Board, model: TI OMAP3 BeagleBoard [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Reserving 12582912 bytes SDRAM for VRAM [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp ) [ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 [ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz [ 0.000000] Reprogramming SDRC clock to 332000000 Hz [ 0.000000] PERCPU: Embedded 8 pages/cpu @c09c6000 s9888 r8192 d14688 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 612 [ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8 root=UUID=7c80 [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] allocated 1310720 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgros [ 0.000000] Memory: 244MB = 244MB total [ 0.000000] Memory: 234688k/234688k available, 27456k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB) [ 0.000000] vmalloc : 0xd0800000 - 0xf8000000 ( 632 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] modules : 0xbf800000 - 0xc0000000 ( 8 MB) [ 0.000000] .init : 0xc0008000 - 0xc0052000 ( 296 kB) [ 0.000000] .text : 0xc0052000 - 0xc0687760 (6358 kB) [ 0.000000] .data : 0xc0688000 - 0xc06f5800 ( 438 kB) [ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU-based detection of stalled CPUs is disabled. [ 0.000000] NR_IRQS:410 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts [ 0.000000] Total of 96 interrupts on 1 active controller [ 0.000000] omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck. [ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 13107199s [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] console [tty0] enabled [ 0.294433] Calibrating delay loop... 518.82 BogoMIPS (lpj=2023424) [ 0.456878] pid_max: default: 32768 minimum: 301 [ 0.461944] Security Framework initialized [ 0.466369] AppArmor: AppArmor initialized [ 0.470703] Yama: becoming mindful. [ 0.474731] Mount-cache hash table entries: 512 [ 0.480499] Initializing cgroup subsys ns [ 0.484741] ns_cgroup deprecated: consider using the 'clone_children' flag without . [ 0.494049] Initializing cgroup subsys cpuacct [ 0.498809] Initializing cgroup subsys memory [ 0.503479] Initializing cgroup subsys devices [ 0.508148] Initializing cgroup subsys freezer [ 0.512969] CPU: Testing write buffer coherency: ok [ 0.518432] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters avaie [ 0.527984] Brought up 1 CPUs [ 0.531158] SMP: Total of 1 processors activated (518.82 BogoMIPS). [ 0.538330] devtmpfs: initialized [ 0.545440] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_core [ 0.552978] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per [ 0.560363] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup [ 0.583587] omap_hwmod: i2c1: softreset failed (waited 10000 usec) [ 0.604492] omap_hwmod: i2c2: softreset failed (waited 10000 usec) [ 0.625366] omap_hwmod: i2c3: softreset failed (waited 10000 usec) [ 0.632507] omap_hwmod: am35x_otg_hs: cannot be enabled (3) [ 0.639465] print_constraints: dummy: [ 0.643829] NET: Registered protocol family 16 [ 0.648834] GPMC revision 5.0 [ 0.653656] OMAP GPIO hardware version 2.5 [ 0.658142] OMAP GPIO hardware version 2.5 [ 0.662567] OMAP GPIO hardware version 2.5 [ 0.667053] OMAP GPIO hardware version 2.5 [ 0.671478] OMAP GPIO hardware version 2.5 [ 0.675933] OMAP GPIO hardware version 2.5 [ 0.682159] omap_mux_init: Add partition: #1: core, flags: 0 [ 0.689392] OMAP3 Beagle Rev: C4 [ 0.695037] omap_device: omap_uart.0: new worst case activate latency 0: 30517 [ 0.705871] Found NAND on CS0 [ 0.709014] Registering NAND on CS0 [ 0.713104] No ATAGs? [ 0.715332] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.726898] OMAP DMA hardware revision 4.0 [ 0.741210] bio: create slab <bio-0> at 0 [ 0.748413] SCSI subsystem initialized [ 0.753295] usbcore: registered new interface driver usbfs [ 0.759216] usbcore: registered new interface driver hub [ 0.765045] usbcore: registered new device driver usb [ 0.786437] omap_i2c omap_i2c.1: bus 1 rev1.3.12 at 2600 kHz [ 0.795532] twl4030: PIH (irq 7) chaining IRQs 368..375 [ 0.801055] twl4030: power (irq 373) chaining IRQs 376..383 [ 0.807556] twl4030: gpio (irq 368) chaining IRQs 384..401 [ 0.816375] print_constraints: VUSB1V5: 1500 mV normal standby [ 0.823181] print_constraints: VUSB1V8: 1800 mV normal standby [ 0.829925] print_constraints: VUSB3V1: 3100 mV normal standby [ 0.837615] print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby [ 0.846099] print_constraints: VDAC: 1800 mV normal standby [ 0.852600] print_constraints: VDVI: 1800 mV normal standby [ 0.859252] print_constraints: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby [ 0.867218] omap_device: omap_i2c.1: new worst case deactivate latency 0: 30517 [ 0.883636] omap_i2c omap_i2c.3: bus 3 rev1.3.12 at 100 kHz [ 0.890930] Advanced Linux Sound Architecture Driver Version 1.0.23. [ 0.898529] NetLabel: Initializing [ 0.902191] NetLabel: domain hash size = 128 [ 0.906799] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.912109] NetLabel: unlabeled traffic allowed by default [ 0.921386] DMA-API: preallocated 4096 debug entries [ 0.926696] DMA-API: debugging enabled by kernel config [ 0.932250] Switching to clocksource 32k_counter [ 0.940521] Switched to NOHz mode on CPU #0 [ 0.958496] AppArmor: AppArmor Filesystem Enabled [ 0.984161] NET: Registered protocol family 2 [ 0.989257] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.997863] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 1.005523] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 1.012512] TCP: Hash tables configured (established 8192 bind 8192) [ 1.019195] TCP reno registered [ 1.022552] UDP hash table entries: 128 (order: 0, 4096 bytes) [ 1.028717] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes) [ 1.035797] NET: Registered protocol family 1 [ 1.041229] RPC: Registered udp transport module. [ 1.046203] RPC: Registered tcp transport module. [ 1.051208] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.058502] Trying to unpack rootfs image as initramfs... [ 1.080322] PMU: registered new PMU device of type 0 [ 1.085845] omap_sr_disable: omap_sr struct for sr_mpu not found [ 1.092254] omap_voltage_scale_vdd: No voltage scale API registered for vdd_mpu [ 1.099945] omap_dvfs_voltage_scale: Unable to scale the mpu to 1350000 volt [ 1.107360] omap_sr_enable: omap_sr struct for sr_mpu not found [ 1.140777] omap_sr_disable: omap_sr struct for sr_mpu not found [ 1.147094] omap_voltage_scale_vdd: No voltage scale API registered for vdd_mpu [ 1.154846] omap_dvfs_voltage_scale: Unable to scale the mpu to 1350000 volt [ 1.162261] omap_sr_enable: omap_sr struct for sr_mpu not found [ 1.181549] LTTng will clear ccnt top bit every 274 jiffies. [ 1.204498] audit: initializing netlink socket (disabled) [ 1.210235] type=2000 audit(0.906:1): initialized [ 1.259826] VFS: Disk quotas dquot_6.5.2 [ 1.264556] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.290496] fuse init (API version 7.16) [ 1.296844] Btrfs loaded [ 1.313232] msgmni has been set to 458 [ 1.330566] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.338409] io scheduler noop registered [ 1.342559] io scheduler deadline registered [ 1.361114] io scheduler cfq registered (default) [ 1.438873] OMAP DSS rev 2.0 [ 1.732666] Freeing initrd memory: 3628K [ 1.766784] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.775360] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 [ 1.783233] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 [ 1.791015] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2 [ 1.798492] console [ttyO2] enabled, bootconsole disabled [ 1.798492] console [ttyO2] enabled, bootconsole disabled [ 1.822387] brd: module loaded [ 1.831726] loop: module loaded [ 1.835845] omap_device: omap_i2c.1: new worst case activate latency 0: 30517 [ 1.845306] omap2-nand driver initializing [ 1.850006] ONFI flash detected [ 1.853668] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1) [ 1.862792] Creating 5 MTD partitions on "omap2-nand.0": [ 1.868469] 0x000000000000-0x000000080000 : "X-Loader" [ 1.876007] 0x000000080000-0x000000260000 : "U-Boot" [ 1.883911] 0x000000260000-0x000000280000 : "U-Boot Env" [ 1.891296] 0x000000280000-0x000000680000 : "Kernel" [ 1.900054] 0x000000680000-0x000010000000 : "File System" [ 2.018951] PPP generic driver version 2.4.2 [ 2.023956] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit . [ 2.034210] CSLIP: code copyright 1989 Regents of the University of California. [ 2.041961] SLIP linefill/keepalive option. [ 2.046661] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.062561] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller [ 4.068603] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 [ 4.076660] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 [ 4.093841] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 [ 4.100952] hub 1-0:1.0: USB hub found [ 4.105010] hub 1-0:1.0: 3 ports detected [ 4.141082] udc: OMAP UDC driver, version: 4 October 2004 (iso) (dma) [ 4.148803] mousedev: PS/2 mouse device common for all mice [ 4.155822] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 [ 4.162536] twl_rtc twl_rtc: Power up reset detected. [ 4.168670] twl_rtc twl_rtc: Enabling TWL-RTC. [ 4.174682] device-mapper: uevent: version 1.0.3 [ 4.180389] device-mapper: ioctl: 4.19.1-ioctl (2011-01-07) initialised: dm-devel@rm [ 4.189819] device-mapper: multipath: version 1.2.0 loaded [ 4.195678] device-mapper: multipath round-robin: version 1.0.0 loaded [ 4.203308] omap_sr_disable: omap_sr struct for sr_mpu not found [ 4.209655] omap_voltage_scale_vdd: No voltage scale API registered for vdd_mpu [ 4.217437] omap_dvfs_voltage_scale: Unable to scale the mpu to 1350000 volt [ 4.224914] omap_sr_enable: omap_sr struct for sr_mpu not found [ 4.231597] cpuidle: using governor ladder [ 4.235992] cpuidle: using governor menu [ 4.240234] sdhci: Secure Digital Host Controller Interface driver [ 4.246765] sdhci: Copyright(c) Pierre Ossman [ 4.362487] OMAP3 Beagle/Devkit8000 SoC init [ 4.446655] asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok [ 4.453308] usb 1-2: new high speed USB device number 2 using ehci-omap [ 4.461486] ALSA device list: [ 4.464630] #0: omap3beagle [ 4.469909] TCP cubic registered [ 4.474792] NET: Registered protocol family 10 [ 4.483459] NET: Registered protocol family 17 [ 4.488586] Registering the dns_resolver key type [ 4.493927] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 1 [ 4.502166] ThumbEE CPU extension supported. [ 4.511138] Power Management for TI OMAP3. [ 4.516540] sr_init: No PMIC hook to init smartreflex [ 4.525451] smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized [ 4.534027] smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized [ 4.542480] SmartReflex Class3 initialized [ 4.560974] registered taskstats version 1 [ 4.597473] fbcvt: 1280x720@60: CVT Name - .921M9-R [ 4.630920] Console: switching to colour frame buffer device 160x45 [ 4.655517] hub 1-2:1.0: USB hub found [ 4.659973] hub 1-2:1.0: 4 ports detected [ 4.953704] usb 1-2.1: new high speed USB device number 3 using ehci-omap [ 5.023712] mmc0: new high speed SDHC card at address 1234 [ 5.030334] mmcblk0: mmc0:1234 SA04G 3.68 GiB [ 5.039367] mmcblk0: p1 p2 [ 5.089508] hub 1-2.1:1.0: USB hub found [ 5.094207] hub 1-2.1:1.0: 3 ports detected [ 5.203552] usb 1-2.4: new high speed USB device number 4 using ehci-omap [ 5.431091] usb 1-2.1.1: new low speed USB device number 5 using ehci-omap [ 5.649841] omap_i2c omap_i2c.1: controller timed out [ 5.655670] usb 1-2.1.2: new low speed USB device number 6 using ehci-omap [ 5.664093] twl: i2c_read failed to transfer all messages [ 5.670013] _regulator_enable: VDVI: is_enabled() failed: -110 [ 5.676361] omapfb omapfb: Failed to enable display 'dvi' [ 5.688262] omapfb omapfb: failed to setup omapfb -- You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. https://bugs.launchpad.net/bugs/754007 Title: omapfb fails on beagle C4 -- ubuntu-bugs mailing list [email protected] https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
