Alright, so this isn't just stuck to 6.10
Just upgraded to 64 bit feisty(kubuntu though that shouldn't make a HUGE
difference), and well, similar problems persist. No shutdown, SATA not being
detected. Please help. I can't afford new hardware :|
Jayanth
lspci -vv follows:
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
Subsystem: Giga-byte Technology Unknown device 5000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2)
Subsystem: Giga-byte Technology Unknown device 5000
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR+ <PERR-
00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2)
Subsystem: Giga-byte Technology Unknown device 5000
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2)
Subsystem: Giga-byte Technology Unknown device 5000
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2)
Subsystem: Giga-byte Technology Unknown device 5000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2)
Subsystem: Giga-byte Technology Unknown device 5000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2)
Subsystem: Giga-byte Technology Unknown device 5000
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2)
Subsystem: Giga-byte Technology Unknown device 5000
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:05.0 VGA compatible controller: nVidia Corporation C51G [GeForce 6100]
(rev a2) (prog-if 00 [VGA])
Subsystem: Giga-byte Technology Unknown device d000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f2000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f3000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: <access denied>
00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
Subsystem: Giga-byte Technology Unknown device 5001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a2)
Subsystem: Giga-byte Technology Unknown device 5001
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a2)
Subsystem: Giga-byte Technology Unknown device 0264
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1c00 [size=64]
Region 5: I/O ports at 1c80 [size=64]
Capabilities: <access denied>
00:0a.2 RAM memory: nVidia Corporation MCP51 Memory Controller 0 (rev a2)
Subsystem: Giga-byte Technology Unknown device 0264
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a2)
(prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Unknown device 5004
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f5108000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a2)
(prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Unknown device 5004
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 5
Region 0: Memory at f5104000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1) (prog-if 8a
[Master SecP PriP])
Subsystem: Giga-byte Technology Unknown device b000
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: <access denied>
00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev
a1) (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology Unknown device b002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at d800 [size=16]
Region 5: Memory at f5107000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev
a1) (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology Unknown device b002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at c400 [size=16]
Region 5: Memory at f5106000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) (prog-if 01
[Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: f5000000-f50fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev
a2)
Subsystem: Giga-byte Technology Unknown device a102
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 5
Region 0: Memory at f5100000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a1)
Subsystem: Giga-byte Technology Unknown device e000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f5105000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at b000 [size=8]
Capabilities: <access denied>
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Capabilities: <access denied>
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM
Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: D-Link System Inc DFE-538TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at f5000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
01:0e.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology GA-7VT600-1394 Motherboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f5001000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at a400 [size=128]
Capabilities: <access denied>
-------------------------------------------------------
Dmesg follows:
[EMAIL PROTECTED]:~/Desktop$ cat dmesg.txt
[ 0.000000] Linux version 2.6.20-15-generic ([EMAIL PROTECTED]) (gcc version
4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Apr 15 06:17:24 UTC 2007 (Ubuntu
2.6.20-15.27-generic)
[ 0.000000] Command line: root=UUID=1b7f52ba-a5a6-4bfb-8108-748da0c4eb33
ro quiet splash noapic acpi=off
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003bff0000 (usable)
[ 0.000000] BIOS-e820: 000000003bff0000 - 000000003bff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003bff3000 - 000000003c000000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003c000000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f2000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 245744) 1 entries of 3200
used
[ 0.000000] end_pfn_map = 1048576
[ 0.000000] DMI 2.3 present.
[ 0.000000] Scanning NUMA topology in Northbridge 24
[ 0.000000] Number of nodes 1
[ 0.000000] Node 0 MemBase 0000000000000000 Limit 000000003bff0000
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 245744) 1 entries of 3200
used
[ 0.000000] NUMA: Using 63 for the hash shift.
[ 0.000000] Using node hash shift of 63
[ 0.000000] Bootmem setup node 0 0000000000000000-000000003bff0000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0 -> 159
[ 0.000000] 0: 256 -> 245744
[ 0.000000] On node 0 totalpages: 245647
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1085 pages reserved
[ 0.000000] DMA zone: 2858 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 3303 pages used for memmap
[ 0.000000] DMA32 zone: 238345 pages, LIFO batch:31
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] MPTABLE: OEM ID: OEM00000 MPTABLE: Product ID: PROD00000000
MPTABLE: APIC at: 0xFEE00000
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] I/O APIC #2 at 0xFEC00000.
[ 0.000000] Setting APIC routing to physical flat
[ 0.000000] Processors: 1
[ 0.000000] Nosave address range: 000000000009f000 - 00000000000a0000
[ 0.000000] Nosave address range: 00000000000a0000 - 00000000000f0000
[ 0.000000] Nosave address range: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 50000000 (gap:
40000000:b0000000)
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 34048 bytes of per cpu data
[ 0.000000] Built 1 zonelists. Total pages: 241203
[ 0.000000] Kernel command line:
root=UUID=1b7f52ba-a5a6-4bfb-8108-748da0c4eb33 ro quiet splash noapic
acpi=off
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 24.210150] Console: colour VGA+ 80x25
[ 24.211026] Dentry cache hash table entries: 131072 (order: 8, 1048576
bytes)
[ 24.212374] Inode-cache hash table entries: 65536 (order: 7, 524288
bytes)
[ 24.212488] Checking aperture...
[ 24.212492] CPU 0: aperture @ 1180000000 size 32 MB
[ 24.212494] Aperture too small (32 MB)
[ 24.219637] No AGP bridge found
[ 24.232340] Memory: 954968k/982976k available (2217k kernel code, 27620k
reserved, 1162k data, 304k init)
[ 24.309326] Calibrating delay using timer specific routine..
3622.14BogoMIPS (lpj=7244288)
[ 24.309396] Security Framework v1.0.0 initialized
[ 24.309404] SELinux: Disabled at boot.
[ 24.309431] Mount-cache hash table entries: 256
[ 24.309600] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 24.309603] CPU: L2 Cache: 512K (64 bytes/line)
[ 24.309606] CPU 0/0 -> Node 0
[ 24.309628] SMP alternatives: switching to UP code
[ 24.309905] Freeing SMP alternatives: 24k freed
[ 24.310024] Early unpacking initramfs... done
[ 24.713010] Using local APIC timer interrupts.
[ 24.768287] result 12557391
[ 24.768289] Detected 12.557 MHz APIC timer.
[ 24.769163] Brought up 1 CPUs
[ 24.769172] time.c: Using 1.193182 MHz WALL PIT GTOD PIT/TSC timer.
[ 24.769174] time.c: Detected 1808.263 MHz processor.
[ 24.769524] Time: 12:18:00 Date: 04/22/107
[ 24.769564] NET: Registered protocol family 16
[ 24.769660] PCI: Using configuration type 1
[ 24.770180] ACPI: Interpreter disabled.
[ 24.770184] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 24.770192] pnp: PnP ACPI: disabled
[ 24.770238] PCI: Probing PCI hardware
[ 24.770242] PCI: Probing PCI hardware (bus 00)
[ 24.770456] Boot video device is 0000:00:05.0
[ 24.771095] PCI: Transparent bridge - 0000:00:10.0
[ 24.772446] PCI: Discovered primary peer bus ff [IRQ]
[ 24.772452] PCI: Using IRQ router default [10de/02f1] at 0000:00:00.0
[ 24.772553] NET: Registered protocol family 8
[ 24.772555] NET: Registered protocol family 20
[ 24.772923] PCI: Bridge: 0000:00:10.0
[ 24.772926] IO window: a000-afff
[ 24.772931] MEM window: f5000000-f50fffff
[ 24.772933] PREFETCH window: disabled.
[ 24.772946] PCI: Setting latency timer of device 0000:00:10.0 to 64
[ 24.773022] NET: Registered protocol family 2
[ 24.805177] IP route cache hash table entries: 32768 (order: 6, 262144
bytes)
[ 24.805472] TCP established hash table entries: 131072 (order: 9, 2097152
bytes)
[ 24.807235] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 24.808134] TCP: Hash tables configured (established 131072 bind 65536)
[ 24.808138] TCP reno registered
[ 24.817233] checking if image is initramfs... it is
[ 25.567406] Freeing initrd memory: 8179k freed
[ 25.575233] audit: initializing netlink socket (disabled)
[ 25.575248] audit(1179836280.316:1): initialized
[ 25.575406] VFS: Disk quotas dquot_6.5.1
[ 25.575424] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 25.575484] io scheduler noop registered
[ 25.575486] io scheduler anticipatory registered
[ 25.575488] io scheduler deadline registered
[ 25.575500] io scheduler cfq registered (default)
[ 25.599056] Real Time Clock Driver v1.12ac
[ 25.599125] Linux agpgart interface v0.102 (c) Dave Jones
[ 25.599128] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
sharing enabled
[ 25.599258] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 25.599694] mice: PS/2 mouse device common for all mice
[ 25.600211] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024
blocksize
[ 25.600445] input: Macintosh mouse button emulation as
/class/input/input0
[ 25.600477] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 25.600482] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
[ 25.600782] PNP: No PS/2 controller found. Probing ports directly.
[ 25.604308] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 25.604315] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 25.604414] TCP cubic registered
[ 25.604422] NET: Registered protocol family 1
[ 25.604461] Magic number: 7:190:330
[ 25.604552] hash matches device tty51
[ 25.604572] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 25.604662] Freeing unused kernel memory: 304k freed
[ 25.631509] input: AT Translated Set 2 keyboard as /class/input/input1
[ 26.815131] Capability LSM initialized
[ 26.830941] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
[EMAIL PROTECTED]
[ 26.876595] thermal: Unknown symbol acpi_processor_set_thermal_limit
[ 27.381921] md: linear personality registered for level -1
[ 27.385149] md: multipath personality registered for level -4
[ 27.388136] md: raid0 personality registered for level 0
[ 27.391669] md: raid1 personality registered for level 1
[ 27.394558] raid5: automatically using best checksumming function:
generic_sse
[ 27.411862] generic_sse: 5782.000 MB/sec
[ 27.411865] raid5: using function: generic_sse (5782.000 MB/sec)
[ 27.483840] raid6: int64x1 1666 MB/s
[ 27.551797] raid6: int64x2 2229 MB/s
[ 27.619766] raid6: int64x4 2317 MB/s
[ 27.687738] raid6: int64x8 1600 MB/s
[ 27.755714] raid6: sse2x1 2320 MB/s
[ 27.823673] raid6: sse2x2 3079 MB/s
[ 27.891649] raid6: sse2x4 3355 MB/s
[ 27.891651] raid6: using algorithm sse2x4 (3355 MB/s)
[ 27.891654] md: raid6 personality registered for level 6
[ 27.891656] md: raid5 personality registered for level 5
[ 27.891658] md: raid4 personality registered for level 4
[ 27.923149] md: raid10 personality registered for level 10
[ 28.072333] usbcore: registered new interface driver usbfs
[ 28.072360] usbcore: registered new interface driver hub
[ 28.072385] usbcore: registered new device driver usb
[ 28.073218] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller
(OHCI) Driver
[ 28.073272] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 28.073276] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 28.073456] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus
number 1
[ 28.073475] ohci_hcd 0000:00:0b.0: irq 10, io mem 0xf5108000
[ 28.126374] forcedeth.c: Reverse Engineered nForce ethernet driver.
Version 0.59.
[ 28.137774] usb usb1: configuration #1 chosen from 1 choice
[ 28.137806] hub 1-0:1.0: USB hub found
[ 28.137818] hub 1-0:1.0: 8 ports detected
[ 28.164726] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 28.176713] ieee1394: Initialized config rom entry `ip1394'
[ 28.244131] PCI: Setting latency timer of device 0000:00:0b.1 to 64
[ 28.244137] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 28.244274] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus
number 2
[ 28.244311] ehci_hcd 0000:00:0b.1: debug port 1
[ 28.244315] PCI: cache line size of 64 is not supported by device
0000:00:0b.1
[ 28.244327] ehci_hcd 0000:00:0b.1: irq 5, io mem 0xf5104000
[ 28.244334] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10
Dec 2004
[ 28.244846] usb usb2: configuration #1 chosen from 1 choice
[ 28.245039] hub 2-0:1.0: USB hub found
[ 28.245049] hub 2-0:1.0: 8 ports detected
[ 28.352062] NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0
[ 28.352084] NFORCE-MCP51: chipset revision 161
[ 28.352087] NFORCE-MCP51: not 100% native mode: will probe irqs later
[ 28.352094] NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller
[ 28.352105] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA,
hdb:DMA
[ 28.352116] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA,
hdd:DMA
[ 28.352125] Probing IDE interface ide0...
[ 29.090964] hda: SONY DVD RW DRU-810A, ATAPI CD/DVD-ROM drive
[ 29.763313] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 29.763558] Probing IDE interface ide1...
[ 30.054460] hdc: HDS728080PLAT20, ATA DISK drive
[ 30.334314] hdd: ST3160215A, ATA DISK drive
[ 30.390833] ide1 at 0x170-0x177,0x376 on irq 15
[ 30.399736] SCSI subsystem initialized
[ 30.407235] libata version 2.20 loaded.
[ 30.413340] sata_nv 0000:00:0e.0: version 3.3
[ 30.413387] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 30.413452] ata1: SATA max UDMA/133 cmd 0x00000000000109f0 ctl
0x0000000000010bf2 bmdma 0x000000000001d800 irq 11
[ 30.413483] ata2: SATA max UDMA/133 cmd 0x0000000000010970 ctl
0x0000000000010b72 bmdma 0x000000000001d808 irq 11
[ 30.413496] scsi0 : sata_nv
[ 30.726013] ata1: SATA link down (SStatus 0 SControl 300)
[ 30.736548] ATA: abnormal status 0x7F on port 0x00000000000109f7
[ 30.736578] scsi1 : sata_nv
[ 31.049847] ata2: SATA link down (SStatus 0 SControl 300)
[ 31.060383] ATA: abnormal status 0x7F on port 0x0000000000010977
[ 31.060480] PCI: Setting latency timer of device 0000:00:0f.0 to 64
[ 31.060525] ata3: SATA max UDMA/133 cmd 0x00000000000109e0 ctl
0x0000000000010be2 bmdma 0x000000000001c400 irq 10
[ 31.060553] ata4: SATA max UDMA/133 cmd 0x0000000000010960 ctl
0x0000000000010b62 bmdma 0x000000000001c408 irq 10
[ 31.060565] scsi2 : sata_nv
[ 31.529615] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 31.537856] ata3.00: ata_hpa_resize 1: sectors = 586070255, hpa_sectors =
586072368
[ 31.537860] ata3.00: Host Protected Area detected.
[ 31.537862] current size : 586070255 sectors (300067 MB)
[ 31.537863] native size : 586072368 sectors (300069 MB)
[ 31.538003] ata3.00: SET of native returned 570425379, expected 586072368
[ 31.549728] ata3.00: Native size increased to 586072368 sectors
[ 31.549734] ata3.00: ATA-7: ST3300831AS, 3.02, max UDMA/133
[ 31.549737] ata3.00: 586072368 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 31.561847] ata3.00: ata_hpa_resize 1: sectors = 586072368, hpa_sectors =
586072368
[ 31.561851] ata3.00: configured for UDMA/133
[ 31.561860] scsi3 : sata_nv
[ 31.877413] ata4: SATA link down (SStatus 0 SControl 300)
[ 31.887946] ATA: abnormal status 0x7F on port 0x0000000000010967
[ 31.888077] scsi 2:0:0:0: Direct-Access ATA ST3300831AS
3.02 PQ: 0 ANSI: 5
[ 31.889452] PCI: Setting latency timer of device 0000:00:14.0 to 64
[ 31.889463] forcedeth: using HIGHDMA
[ 31.910289] hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache,
UDMA(33)
[ 31.910300] Uniform CD-ROM driver Revision: 3.20
[ 31.923302] hdc: max request size: 512KiB
[ 31.925312] SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB)
[ 31.925333] sda: Write Protect is off
[ 31.925335] sda: Mode Sense: 00 3a 00 00
[ 31.925349] SCSI device sda: write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 31.925464] SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB)
[ 31.925472] sda: Write Protect is off
[ 31.925474] sda: Mode Sense: 00 3a 00 00
[ 31.925486] SCSI device sda: write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 31.925492] sda:<6>hdc: Host Protected Area detected.
[ 31.929873] current capacity is 160834367 sectors (82347 MB)
[ 31.929875] native capacity is 160836480 sectors (82348 MB)
[ 31.930112] hdc: Host Protected Area disabled.
[ 31.930116] hdc: 160836480 sectors (82348 MB) w/1719KiB Cache,
CHS=16383/255/63, UDMA(133)
[ 31.930382] hdc: cache flushes supported
[ 31.930433] hdc: hdc1 hdc2 hdc3
[ 31.950184]
[ 31.950370] sd 2:0:0:0: Attached scsi disk sda
[ 31.954644] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 31.956471] hdd: max request size: 512KiB
[ 31.992904] hdd: 312581808 sectors (160041 MB) w/2048KiB Cache,
CHS=19457/255/63, UDMA(100)
[ 32.017318] hdd: cache flushes supported
[ 32.017387] hdd: hdd1
[ 32.413798] eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:
14.0
[ 32.413917] 8139cp 0000:01:06.0: This (id 10ec:8139 rev 10) is not an
8139C+ compatible chip
[ 32.413920] 8139cp 0000:01:06.0: Try the "8139too" driver instead.
[ 32.415581] 8139too Fast Ethernet driver 0.9.28
[ 32.415995] eth1: RealTek RTL8139 at 0xffffc2000002a000,
00:08:a1:97:47:8e, IRQ 5
[ 32.415997] eth1: Identified 8139 chip type 'RTL-8100B/8139D'
[ 32.470122] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11]
MMIO=[f5001000-f50017ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 32.486972] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 32.486976] EXT3-fs: write access will be enabled during recovery.
[ 33.752610] ieee1394: Host added: ID:BUS[0-00:1023]
GUID[000014850030481d]
[ 35.424969] kjournald starting. Commit interval 5 seconds
[ 35.424991] EXT3-fs: recovery complete.
[ 35.425478] EXT3-fs: mounted filesystem with ordered data mode.
[ 43.574231] eth1: link down
[ 44.863982] NET: Registered protocol family 17
[ 45.923507] i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1c00
[ 45.923558] i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c80
[ 46.027523] nvidia: module license 'NVIDIA' taints kernel.
[ 46.297112] PCI: Setting latency timer of device 0000:00:05.0 to 64
[ 46.297332] NVRM: loading NVIDIA Linux x86_64 Kernel Module 1.0-9631
Thu Nov 9 17:35:27 PST 2006
[ 46.665881] PCI: Setting latency timer of device 0000:00:10.1 to 64
[ 47.039824] input: ImPS/2 Logitech Wheel Mouse as /class/input/input2
[ 47.119397] parport0: PC-style at 0x378 [PCSPP,TRISTATE]
[ 47.225664] lp0: using parport0 (polling).
[ 47.494179] fuse init (API version 7.8)
[ 47.565503] Adding 1052248k swap on
/dev/disk/by-uuid/0bafe25a-89b3-4263-8aa0-dbd629b247c2. Priority:-1
extents:1 across:1052248k
[ 47.643729] EXT3 FS on hdc1, internal journal
[ 47.954850] NET: Registered protocol family 10
[ 47.954949] lo: Disabled Privacy Extensions
[ 47.955291] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 58.371713] eth0: no IPv6 routers present
[ 63.077428] kjournald starting. Commit interval 5 seconds
[ 63.077554] EXT3 FS on dm-1, internal journal
[ 63.077558] EXT3-fs: mounted filesystem with ordered data mode.
[ 63.108484] NTFS driver 2.1.28 [Flags: R/O MODULE].
[ 63.111702] NTFS-fs warning (device hdd1): parse_options(): Option
iocharset is deprecated. Please use option nls=<charsetname> in the future.
[ 63.160959] NTFS volume version 3.1.
[ 63.198603] Adding 1052248k swap on
/dev/disk/by-uuid/0bafe25a-89b3-4263-8aa0-dbd629b247c2. Priority:-2
extents:1 across:1052248k
[ 68.748522] powernow_k8: Unknown symbol acpi_processor_notify_smm
[ 68.748569] powernow_k8: Unknown symbol
acpi_processor_unregister_performance
[ 68.748673] powernow_k8: Unknown symbol
acpi_processor_register_performance
[ 68.778613] acpi_cpufreq: Unknown symbol acpi_processor_notify_smm
[ 68.778661] acpi_cpufreq: Unknown symbol
acpi_processor_unregister_performance
[ 68.778781] acpi_cpufreq: Unknown symbol
acpi_processor_preregister_performance
[ 68.778838] acpi_cpufreq: Unknown symbol
acpi_processor_register_performance
[ 70.671454] spurious 8259A interrupt: IRQ7.
[ 76.967313] **WARNING** I2C adapter driver [NVIDIA i2c adapter 0 at 0:
05.0] forgot to specify physical device; fix it!
[ 76.969973] **WARNING** I2C adapter driver [NVIDIA i2c adapter 1 at 0:
05.0] forgot to specify physical device; fix it!
[ 76.972725] **WARNING** I2C adapter driver [NVIDIA i2c adapter 2 at 0:
05.0] forgot to specify physical device; fix it!
[ 77.694826] ppdev: user-space parallel port driver
[ 78.458511] Bluetooth: Core ver 2.11
[ 78.458578] NET: Registered protocol family 31
[ 78.458580] Bluetooth: HCI device and connection manager initialized
[ 78.458584] Bluetooth: HCI socket layer initialized
[ 78.535882] Bluetooth: L2CAP ver 2.8
[ 78.535887] Bluetooth: L2CAP socket layer initialized
[ 78.615873] Bluetooth: RFCOMM socket layer initialized
[ 78.615892] Bluetooth: RFCOMM TTY layer initialized
[ 78.615894] Bluetooth: RFCOMM ver 1.8
[ 89.503535] eth0: no IPv6 routers present
--------------------------------------------------------------------------------------------------------
Disregard the "noapic" option. I am running with noapic and acpi=off, well
no luck
Please look into it.
Thank you,
Jayanth
--
Live CD crashes/gets into an endlsess loop on shutdown
https://bugs.launchpad.net/bugs/84719
You received this bug notification because you are a member of Ubuntu
Bugs, which is the bug contact for Ubuntu.
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
