Attached
On 7/9/07, Kyle McMartin <[EMAIL PROTECTED]> wrote:
> We need the output of "lspci -vvnn" to be able to know what pci id your
> device is.
>
> ** Changed in: linux-source-2.6.22 (Ubuntu)
> Status: New => Incomplete
>
> --
> RaLink 2500 not showing in kernel 2.6.22
> https://bugs.launchpad.net/bugs/124323
> You received this bug notification because you are a direct subscriber
> of the bug.
>
00:00.0 Host bridge [0600]: Silicon Integrated Systems [SiS] 760/M760 Host
[1039:0760] (rev 03)
Subsystem: Uniwill Computer Corp Unknown device [1584:5040]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=32M]
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=3 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW-
Rate=<none>
Capabilities: [d0] HyperTransport: Slave or Primary Interface
!!! Possibly incomplete decoding
Command: BaseUnitID=0 UnitCnt=9 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC+ TXO-
<CRCErr=0
Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+
<CRCErr=0
Link Config 1: MLWI=N/C MLWO=N/C LWI=N/C LWO=N/C
Revision ID: 1.02
Capabilities: [f0] HyperTransport: Interrupt Discovery and Configuration
00:01.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] SG86C202
[1039:0002] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: dfe00000-dfefffff
Prefetchable memory behind bridge: cfd00000-dfcfffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
00:02.0 ISA bridge [0601]: Silicon Integrated Systems [SiS] SiS963 [MuTIOL
Media IO] [1039:0963] (rev 25)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:02.1 SMBus [0c05]: Silicon Integrated Systems [SiS] SiS961/2 SMBus
Controller [1039:0016]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 0
Region 4: I/O ports at 0c00 [size=32]
00:02.5 IDE interface [0101]: Silicon Integrated Systems [SiS] 5513 [IDE]
[1039:5513] (prog-if 80 [Master])
Subsystem: Uniwill Computer Corp Unknown device [1584:5102]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at ffa0 [size=16]
00:02.6 Modem [0703]: Silicon Integrated Systems [SiS] AC'97 Modem Controller
[1039:7013] (rev a0) (prog-if 00 [Generic])
Subsystem: Uniwill Computer Corp Unknown device [1584:4003]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 17
Region 0: I/O ports at e400 [size=256]
Region 1: I/O ports at e000 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.7 Multimedia audio controller [0401]: Silicon Integrated Systems [SiS]
AC'97 Sound Controller [1039:7012] (rev a0)
Subsystem: Uniwill Computer Corp Unknown device [1584:8403]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 17
Region 0: I/O ports at e800 [size=256]
Region 1: I/O ports at ec00 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.0
Controller [1039:7001] (rev 0f) (prog-if 10 [OHCI])
Subsystem: Uniwill Computer Corp Unknown device [1584:5102]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at dfffd000 (32-bit, non-prefetchable) [size=4K]
00:03.1 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.0
Controller [1039:7001] (rev 0f) (prog-if 10 [OHCI])
Subsystem: Uniwill Computer Corp Unknown device [1584:5102]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin B routed to IRQ 19
Region 0: Memory at dfffe000 (32-bit, non-prefetchable) [size=4K]
00:03.3 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 2.0
Controller [1039:7002] (prog-if 20 [EHCI])
Subsystem: Uniwill Computer Corp Unknown device [1584:5102]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (20000ns max)
Interrupt: pin D routed to IRQ 20
Region 0: Memory at dffff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] SiS900 PCI
Fast Ethernet [1039:0900] (rev 91)
Subsystem: Uniwill Computer Corp Unknown device [1584:5200]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (13000ns min, 2750ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at dfffc000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at dffc0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB22/A
IEEE-1394a-2000 Controller (PHY/Link) [104c:8023] (prog-if 10 [OHCI])
Subsystem: Uniwill Computer Corp Unknown device [1584:7000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at dfffb800 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at dfff4000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:09.0 CardBus bridge [0607]: O2 Micro, Inc. OZ711M1/MC1 4-in-1 MemoryCardBus
Controller [1217:7114] (rev 20)
Subsystem: Uniwill Computer Corp Unknown device [1584:3008]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 50000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 40000000-43fff000 (prefetchable)
Memory window 1: 44000000-47fff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:09.1 CardBus bridge [0607]: O2 Micro, Inc. OZ711M1/MC1 4-in-1 MemoryCardBus
Controller [1217:7114] (rev 20)
Subsystem: Uniwill Computer Corp Unknown device [1584:3008]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at 50001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 48000000-4bfff000 (prefetchable)
Memory window 1: 4c000000-4ffff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
00:09.2 System peripheral [0880]: O2 Micro, Inc. OZ711Mx 4-in-1 MemoryCardBus
Accelerator [1217:7110]
Subsystem: Uniwill Computer Corp Unknown device [1584:3008]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at dfffa000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 Network controller [0280]: RaLink RT2500 802.11g Cardbus/mini-PCI
[1814:0201] (rev 01)
Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:6833]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at dfff8000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
01:00.0 VGA compatible controller [0300]: Silicon Integrated Systems [SiS]
661/741/760 PCI/AGP or 662/761Gx PCIE VGA Display Adapter [1039:6330] (prog-if
00 [VGA])
Subsystem: Uniwill Computer Corp Unknown device [1584:5040]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
BIST result: 00
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at dfee0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at cc00 [size=128]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
--
RaLink 2500 not showing in kernel 2.6.22
https://bugs.launchpad.net/bugs/124323
You received this bug notification because you are a member of Ubuntu
Bugs, which is the bug contact for Ubuntu.
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
