...some more dmesg output appears after 30 seconds...
[ 35.193319] ata11.00: qc timeout (cmd 0xef)
[ 35.193327] ata6.00: qc timeout (cmd 0x27)
[ 35.201309] ata6.00: failed to read native max address (err_mask=0x4)
[ 35.201311] ata6.00: HPA support seems broken, skipping HPA handling
[ 35.201322] ata11.00: failed to IDENTIFY (SPINUP failed, err_mask=0x4)
[ 35.201325] ata11: hard resetting link
[ 35.529001] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 37.503336] ata9.00: ATA-8: Hitachi HDS5C3020BLE630, MZ4OAAB0, max UDMA/133
[ 37.503339] ata9.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 37.505381] ata10.00: ATA-8: Hitachi HDS5C3020BLE630, MZ4OAAB0, max UDMA/133
[ 37.505383] ata10.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32),
AA
[ 37.505490] ata9.00: configured for UDMA/133
[ 37.505493] ata9: EH complete
[ 37.505575] scsi 8:0:0:0: Direct-Access ATA Hitachi HDS5C302 AAB0
PQ: 0 ANSI: 5
[ 37.505839] sd 8:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 37.505841] sd 8:0:0:0: [sdb] 4096-byte physical blocks
[ 37.505865] sd 8:0:0:0: [sdb] Write Protect is off
[ 37.505866] sd 8:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 37.505877] sd 8:0:0:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 37.505954] sd 8:0:0:0: Attached scsi generic sg1 type 0
[ 37.526616] random: nonblocking pool is initialized
[ 37.526979] sdb: unknown partition table
[ 37.527090] ata10.00: configured for UDMA/133
[ 37.527095] ata10: EH complete
[ 37.527114] sd 8:0:0:0: [sdb] Attached SCSI disk
[ 37.527133] scsi 9:0:0:0: Direct-Access ATA Hitachi HDS5C302 AAB0
PQ: 0 ANSI: 5
[ 37.527262] sd 9:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00
TB/1.81 TiB)
[ 37.527264] sd 9:0:0:0: [sdc] 4096-byte physical blocks
[ 37.527291] sd 9:0:0:0: Attached scsi generic sg2 type 0
[ 37.527294] sd 9:0:0:0: [sdc] Write Protect is off
[ 37.527296] sd 9:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 37.527311] sd 9:0:0:0: [sdc] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 37.527438] scsi 12:0:0:0: Processor Marvell 91xx Config 1.01
PQ: 0 ANSI: 5
[ 37.543042] ata11: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 37.547020] ata13.00: exception Emask 0x1 SAct 0x0 SErr 0x0 action 0x0
[ 37.547050] ata13.00: irq_stat 0x40000001
[ 37.547065] scsi 12:0:0:0: CDB:
[ 37.547066] Inquiry: 12 01 00 00 ff 00
[ 37.547072] ata13.00: cmd a0/01:00:00:00:01/00:00:00:00:00/a0 tag 2 dma
16640 in
[ 37.547072] res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x1
(device error)
[ 37.547113] ata13.00: status: { DRDY }
[ 37.547271] scsi 12:0:0:0: Attached scsi generic sg3 type 3
[ 37.551010] ata11: EH complete
[ 37.555858] sdc: unknown partition table
[ 37.555981] sd 9:0:0:0: [sdc] Attached SCSI disk
[ 38.459348] init: failsafe main process (538) killed by TERM signal
--
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
https://bugs.launchpad.net/bugs/1347936
Title:
88SE9130 + Sil3726: not all drives detected on cold boot with power-up
in standby enabled
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1347936/+subscriptions
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
