I just spent a lot of time testing the nm applet on an updated (as of
20071017) Ubuntu Gutsy RC1 using a whole bunch of different network
adapters. I found that the applet won't connect automatically with a
few cards only. Big report follows and syslog is attached. I also
moved the drive to an Intel D815EEA system and tested #1 again but got
the same result (the built-in port worked successfully). I also tried
enabling/disabling the Award BIOS PNP OS option but the results were the
same. I tested the cards multiple times and the results are 100%
repeatable. The only thing I haven't tried is a virgin Gutsy RC1
install on a completely different system with the same cards.
nm-applet 0.6.5
Ubuntu 7.10 (Gutsy RC1)
Linux restore1 2.6.22-14-generic #1 SMP Sun Oct 14 23:05:12 GMT 2007 i686
GNU/Linux
HP Pavilion 8705
Pentium III 800MHz
Via Apollo MVP3/Pro133x AGP
ASUS CUV-NT motherboard
FAILS: When desktop loads, applet indicates no network found, Firefox can't
access the Internet. Manually selecting "Wired Network" fixes the problem.
SUCCESS: When desktop loads, applet indicates "Wired network connection",
Firefox can browse the Internet.
#1 (FAILS)
dmesg:
[ 8.252000] eth0: RealTek RTL-8029 found at 0xb800, IRQ 11,
00:40:05:59:12:CF.
ifconfig -a:
eth0 Link encap:Ethernet HWaddr 00:40:05:59:12:CF
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:647 (647.0 b) TX bytes:0 (0.0 b)
Interrupt:11 Base address:0xb800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lspci -vv:
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=32]
lspci -vvn:
00:0b.0 0200: 10ec:8029
Subsystem: 10ec:8029
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=32]
#2 (FAILS)
dmesg:
[ 19.977677] eth0: Macronix 98715 PMAC rev 32 at Port 0xb800,
00:80:AD:3B:A0:DB, IRQ 11.
ifconfig -a:
eth1 Link encap:Ethernet HWaddr 00:80:AD:3B:A0:DB
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:707 (707.0 b) TX bytes:0 (0.0 b)
Interrupt:11 Base address:0xb800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lspci -vv:
00:0b.0 Ethernet controller: Macronix, Inc. [MXIC] MX987x5 (rev 20)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 20000000 [disabled] [size=64K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1+,D2-,D3hot-,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
lspci -vvn:
00:0b.0 0200: 10d9:0531 (rev 20)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 20000000 [disabled] [size=64K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1+,D2-,D3hot-,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
#3 (SUCCESS)
dmesg:
[ 8.200000] eth0: SMSC EPIC/100 83c170 at 0xb800, IRQ 11, 00:e0:29:19:be:a9.
[ 39.200000] eth2: Setting full-duplex based on MII #3 link partner
capability of 45e1.
[ 67.676000] eth2: no IPv6 routers present
ifconfig -a:
eth2 Link encap:Ethernet HWaddr 00:E0:29:19:BE:A9
inet addr:192.168.11.135 Bcast:192.168.11.255 Mask:255.255.255.0
inet6 addr: fe80::2e0:29ff:fe19:bea9/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:96 errors:0 dropped:0 overruns:0 frame:0
TX packets:152 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:92056 (89.8 KB) TX bytes:28721 (28.0 KB)
Interrupt:11 Base address:0xb800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lspci -vv:
00:0b.0 Ethernet controller: Standard Microsystems Corp [SMC] 83c170 EPIC/100
Fast Ethernet Adapter (rev 06)
Subsystem: Standard Microsystems Corp [SMC] EtherPower II 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 7000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 20000000 [disabled] [size=64K]
lspci -vvn:
00:0b.0 0200: 10b8:0005 (rev 06)
Subsystem: 10b8:a011
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 7000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 20000000 [disabled] [size=64K]
#4 (SUCCESS)
dmesg:
[ 8.256000] eth0: Davicom DM9102 at pci0000:00:0b.0, 00:80:ad:73:10:ef, irq
11.
[ 70.020000] eth3: no IPv6 routers present
ifconfig -a:
eth3 Link encap:Ethernet HWaddr 00:80:AD:73:10:EF
inet addr:192.168.11.133 Bcast:192.168.11.255 Mask:255.255.255.0
inet6 addr: fe80::280:adff:fe73:10ef/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:56 errors:0 dropped:0 overruns:0 frame:0
TX packets:162 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:26696 (26.0 KB) TX bytes:24275 (23.7 KB)
Interrupt:11 Base address:0xb800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lspci -vv:
00:0b.0 Ethernet controller: Davicom Semiconductor, Inc. 21x4x DEC-Tulip
compatible 10/100 Ethernet (rev 31)
Subsystem: Unknown device 4554:434e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 32 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 20000000 [disabled] [size=256K]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
lspci -vvn:
00:0b.0 0200: 1282:9102 (rev 31)
Subsystem: 4554:434e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 32 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 20000000 [disabled] [size=256K]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
#5 (SUCCESS)
dmesg:
[ 36.248000] eth4: setting full-duplex.
[ 69.992000] eth4: no IPv6 routers present
ifconfig -a:
eth4 Link encap:Ethernet HWaddr 00:50:DA:BD:4D:97
inet addr:192.168.11.132 Bcast:192.168.11.255 Mask:255.255.255.0
inet6 addr: fe80::250:daff:febd:4d97/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:52 errors:0 dropped:0 overruns:0 frame:0
TX packets:117 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:26377 (25.7 KB) TX bytes:20885 (20.3 KB)
Interrupt:10 Base address:0xa000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lspci -vv:
00:0b.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74)
Subsystem: 3Com Corporation 3C905CX-TX/TX-M Fast Etherlink for PC
Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at b800 [size=128]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=128]
[virtual] Expansion ROM at 20000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
lspci -vvn:
00:0b.0 0200: 10b7:9200 (rev 74)
Subsystem: 10b7:1000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at b800 [size=128]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=128]
[virtual] Expansion ROM at 20000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
#6 (SUCCESS)
dmesg:
[ 8.256000] e100: eth0: e100_probe: addr 0xdf000000, irq 10, MAC addr
00:06:29:4F:7D:DB
[ 36.456000] e100: eth5: e100_watchdog: link up, 100Mbps, full-duplex
[ 67.592000] eth5: no IPv6 routers present
ifconfig -a:
eth5 Link encap:Ethernet HWaddr 00:06:29:4F:7D:DB
inet addr:192.168.11.140 Bcast:192.168.11.255 Mask:255.255.255.0
inet6 addr: fe80::206:29ff:fe4f:7ddb/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:16 errors:0 dropped:0 overruns:0 frame:0
TX packets:60 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2377 (2.3 KB) TX bytes:8044 (7.8 KB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lspci -vv:
00:0b.0 Ethernet controller: Intel Corporation 82557/8/9 Ethernet Pro 100 (rev
08)
Subsystem: IBM 10/100 EtherJet Adapter with Alert on LAN
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at b800 [size=64]
Region 2: Memory at de800000 (32-bit, non-prefetchable) [size=1M]
[virtual] Expansion ROM at 20000000 [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
lspci -vvn:
00:0b.0 0200: 8086:1229 (rev 08)
Subsystem: 1014:405c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at b800 [size=64]
Region 2: Memory at de800000 (32-bit, non-prefetchable) [size=1M]
[virtual] Expansion ROM at 20000000 [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
#7 (SUCCESS)
dmesg:
[ 22.330769] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 8.244000] 8139too Fast Ethernet driver 0.9.28
[ 8.244000] eth0: RealTek RTL8139 at 0xd083c000, 00:e0:7d:bb:df:a6, IRQ 11
[ 8.244000] eth0: Identified 8139 chip type 'RTL-8139C'
[ 36.232000] eth6: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 74.884000] eth6: no IPv6 routers present
ifconfig -a:
eth6 Link encap:Ethernet HWaddr 00:E0:7D:BB:DF:A6
inet addr:192.168.11.131 Bcast:192.168.11.255 Mask:255.255.255.0
inet6 addr: fe80::2e0:7dff:febb:dfa6/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:14 errors:0 dropped:0 overruns:0 frame:0
TX packets:65 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1834 (1.7 KB) TX bytes:9166 (8.9 KB)
Interrupt:11 Base address:0xc000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lspci -vv:
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
lspci -vvn:
00:0b.0 0200: 10ec:8139 (rev 10)
Subsystem: 10ec:8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
#8 (SUCCESS)
dmesg:
[ 20.338813] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 8.404000] 8139too Fast Ethernet driver 0.9.28
[ 8.404000] eth0: RealTek RTL8139 at 0xd083c000, 00:40:f4:84:f9:ac, IRQ 11
[ 8.404000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 36.176000] eth7: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 67.916000] eth7: no IPv6 routers present
ifconfig -a:
eth7 Link encap:Ethernet HWaddr 00:40:F4:84:F9:AC
inet addr:192.168.11.143 Bcast:192.168.11.255 Mask:255.255.255.0
inet6 addr: fe80::240:f4ff:fe84:f9ac/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:14 errors:0 dropped:0 overruns:0 frame:0
TX packets:63 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1850 (1.8 KB) TX bytes:8569 (8.3 KB)
Interrupt:11 Base address:0xc000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lspci -vv:
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
lspci -vvn:
00:0b.0 0200: 10ec:8139 (rev 10)
Subsystem: 10ec:8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
#9 (SUCCESS)
dmesg:
[ 27.316000] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet
driver
[ 27.352000] pegasus 1-2.1:1.0: eth0, Linksys USB100TX, 00:e0:98:8b:91:4d
[ 36.408000] eth8: set allmulti
[ 36.408000] eth8: set allmulti
[ 36.572000] eth8: set allmulti
[ 36.804000] eth8: set allmulti
[ 37.068000] eth8: set allmulti
[ 37.328000] eth8: set allmulti
[ 37.592000] eth8: set allmulti
[ 37.856000] eth8: set allmulti
[ 38.116000] eth8: set allmulti
[ 38.380000] eth8: set allmulti
[ 38.640000] eth8: set allmulti
[ 38.904000] eth8: set allmulti
[ 39.164000] eth8: set allmulti
[ 39.424000] eth8: set allmulti
[ 39.684000] eth8: set allmulti
[ 39.960000] eth8: set allmulti
[ 40.212000] eth8: set allmulti
[ 40.476000] eth8: set allmulti
[ 40.732000] eth8: set allmulti
[ 40.996000] eth8: set allmulti
[ 41.252000] eth8: set allmulti
[ 41.512000] eth8: set allmulti
[ 41.776000] eth8: set allmulti
[ 42.036000] eth8: set allmulti
[ 42.300000] eth8: set allmulti
[ 42.560000] eth8: set allmulti
[ 42.824000] eth8: set allmulti
[ 43.080000] eth8: set allmulti
[ 43.340000] eth8: set allmulti
[ 43.604000] eth8: set allmulti
[ 43.864000] eth8: set allmulti
[ 44.128000] eth8: set allmulti
[ 44.384000] eth8: set allmulti
[ 44.644000] eth8: set allmulti
[ 44.904000] eth8: set allmulti
[ 45.168000] eth8: set allmulti
[ 45.432000] eth8: set allmulti
[ 45.692000] eth8: set allmulti
[ 45.956000] eth8: set allmulti
[ 46.212000] eth8: set allmulti
[ 46.476000] eth8: set allmulti
[ 46.736000] eth8: set allmulti
[ 47.044000] eth8: set allmulti
[ 47.284000] eth8: set allmulti
[ 47.520000] eth8: set allmulti
[ 47.776000] eth8: set allmulti
[ 48.048000] eth8: set allmulti
[ 48.300000] eth8: set allmulti
[ 48.604000] eth8: set allmulti
[ 48.836000] eth8: set allmulti
[ 49.084000] eth8: set allmulti
[ 49.344000] eth8: set allmulti
[ 49.612000] eth8: set allmulti
[ 49.880000] eth8: set allmulti
[ 52.144000] eth8: set allmulti
[ 53.856000] eth8: set allmulti
[ 53.856000] eth8: set allmulti
[ 55.660000] eth8: set allmulti
[ 55.664000] eth8: set allmulti
[ 55.664000] eth8: set allmulti
[ 55.748000] eth8: set allmulti
[ 55.756000] eth8: set allmulti
[ 57.788000] eth8: set allmulti
[ 57.788000] eth8: set allmulti
[ 68.564000] eth8: no IPv6 routers present
ifconfig -a:
eth8 Link encap:Ethernet HWaddr 00:E0:98:8B:91:4D
inet addr:192.168.11.130 Bcast:192.168.11.255 Mask:255.255.255.0
inet6 addr: fe80::2e0:98ff:fe8b:914d/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:67 errors:0 dropped:0 overruns:0 frame:0
TX packets:134 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:35839 (34.9 KB) TX bytes:30020 (29.3 KB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lsusb -v
Bus 001 Device 003: ID 066b:2203 Linksys, Inc. USB100TX Ethernet [pegasus]
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x066b Linksys, Inc.
idProduct 0x2203 USB100TX Ethernet [pegasus]
bcdDevice 1.01
iManufacturer 1 LINKSYS Inc.
iProduct 2 LINKSYS USB Adapter
iSerial 3 8b914d
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 286mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 0 (Defined at Interface level)
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 128
Device Status: 0x0000
(Bus Powered)
#10 (SUCCESS)
Note: Motorola WPCI810G wireless adapter. Set to target network
(530_Lockwood-PUBLIC) and then restarted to test.
dmesg:
[ 128.156000] eth9: no IPv6 routers present
[ 24.312000] bcm43xx driver
ifconfig -a:
eth9 Link encap:Ethernet HWaddr 00:0C:E5:53:44:C3
inet addr:192.168.13.147 Bcast:192.168.13.255 Mask:255.255.255.0
inet6 addr: fe80::20c:e5ff:fe53:44c3/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:35 errors:0 dropped:0 overruns:0 frame:0
TX packets:227 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:7974 (7.7 KB) TX bytes:21683 (21.1 KB)
Interrupt:255 Base address:0xc000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
iwconfig:
lo no wireless extensions.
eth9 IEEE 802.11b/g ESSID:"530_Lockwood-PUBLIC" Nickname:"Broadcom 4306"
Mode:Managed Frequency=2.437 GHz Access Point: 00:04:E2:D0:D8:14
Bit Rate=24 Mb/s Tx-Power=19 dBm
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality=73/100 Signal level=-56 dBm Noise level=-71 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
lspci -vv:
00:0b.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN
Controller (rev 03)
Subsystem: Motorola Unknown device 7010
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 10
Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=8K]
lspci -vvn:
00:0b.0 0280: 14e4:4320 (rev 03)
Subsystem: 1057:7010
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 10
Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=8K]
#11 (SUCCESS)
Note: CompUSA branded PCI wireless adapter, PN: 1244-00000403-010. Possibly a
SafeCom Technologies SWLPR-5400. Applet doesn't show signal strength.
dmesg:
[ 24.124000] rtl_ieee80211_crypt: registered algorithm 'NULL'
[ 24.124000] rtl_ieee80211_crypt: registered algorithm 'TKIP'
[ 24.124000] rtl_ieee80211_crypt: registered algorithm 'WEP'
[ 24.124000] rtl_ieee80211_crypt: registered algorithm 'CCMP'
[ 24.144000] Linux kernel driver for RTL8180 / RTL8185 based WLAN cards
[ 24.144000] rtl8180: Initializing module
[ 24.144000] rtl8180: Wireless extensions version 22
[ 24.144000] rtl8180: Initializing proc filesystem
[ 24.144000] rtl8180: Configuring chip resources
[ 24.144000] rtl8180: Memory mapped space @ 0xdf000000
[ 24.144000] rtl8180: MAC controller is a RTL8185 b/g (V. D)
[ 24.144000] rtl8180: This is a PCI NIC
[ 24.144000] rtl8180: Reported EEPROM chip is a 93c56 (2Kbit)
[ 24.152000] rtl8180: Card MAC address is 00:0e:2e:6d:7b:12
[ 24.168000] rtl8180: EEPROM version 105
[ 24.168000] rtl8180: Card reports RF frontend Realtek 8225
[ 24.168000] rtl8180: WW:This driver has EXPERIMENTAL support for this
chipset.
[ 24.168000] rtl8180: WW:use it with care and at your own risk and
[ 24.168000] rtl8180: WW:**PLEASE** REPORT SUCCESS/INSUCCESS TO [EMAIL
PROTECTED]
[ 24.168000] rtl8180: Energy threshold: b
[ 24.168000] rtl8180: PAPE from CONFIG2: 6
[ 24.168000] rtl8180: IRQ 11
[ 24.168000] rtl8180: Driver probe completed
[ 36.216000] rtl8180: Bringing up iface
[ 36.428000] rtl8180: Card successfully reset
[ 37.420000] rtl8180: Setting SW wep key
[ 130.372000] rtl8180: Setting SW wep key
[ 130.372000] rtl8180: Setting SW wep key
[ 130.372000] rtl8180: Setting SW wep key
[ 130.372000] rtl8180: Setting SW wep key
[ 130.480000] rtl8180: Setting SW wep key
ifconfig -a:
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wlan0 Link encap:Ethernet HWaddr 00:0E:2E:6D:7B:12
inet addr:192.168.13.146 Bcast:192.168.13.255 Mask:255.255.255.0
inet6 addr: fe80::20e:2eff:fe6d:7b12/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:114 errors:0 dropped:74 overruns:0 frame:0
TX packets:206 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:37304 (36.4 KB) TX bytes:18948 (18.5 KB)
Interrupt:11 Memory:d0926000-d0926100
iwconfig:
lo no wireless extensions.
wlan0 802.11b/g linked ESSID:"530_Lockwood-PUBLIC"
Mode:Managed Frequency=2.437 GHz Access Point: 00:04:E2:D0:D8:14
Bit Rate=54 Mb/s
Retry:on Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
lspci -vv:
00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE
802.11a/b/g Wireless LAN Controller (rev 20)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g
Wireless LAN Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=512]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
lspci -vvn:
00:0b.0 0200: 10ec:8185 (rev 20)
Subsystem: 10ec:8185
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at df000000 (32-bit, non-prefetchable) [size=512]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
modprobe -l:
/lib/modules/2.6.22-14-generic/ubuntu/wireless/rtl8180/rtl8180/r8180.ko
** Attachment added: "syslog"
http://launchpadlibrarian.net/10051951/syslog_CUV-NT.bz2
--
[feisty fawn] NetworkManager reports incorrect online status
https://bugs.launchpad.net/bugs/82927
You received this bug notification because you are a member of Ubuntu
Bugs, which is the bug contact for Ubuntu.
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
