Also affected by this. I'm running Debian 8.9 up to date.
(Linux phlsys 3.16.0-4-amd64 #1 SMP Debian 3.16.43-2+deb8u3 (2017-08-15)
x86_64 GNU/Linux)
syslog shows : (each 10mn)
Aug 26 07:02:06 phlsys udisksd[2161]: Error performing housekeeping for
drive /org/freedesktop/UDisks2/drives/ST1000DM003_1SB10C_W9A07ER1: Error
updating SMART data: sk_disk_check_sleep_mode: Operation not supported
(udisks-error-quark, 0)
GSmartControl doesn't show any error.
Output of smartctl:
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.14 (AF)
Device Model: ST1000DM003-1SB10C
Serial Number: W9A07ER1
LU WWN Device Id: 5 000c50 08b7c0db3
Firmware Version: CC41
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sat Aug 26 08:07:50 2017 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 103) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x10a5) SCT Status supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 083 066 006 Pre-fail Always
- 201611737
3 Spin_Up_Time 0x0003 098 097 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always
- 259
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000f 100 253 045 Pre-fail Always
- 999312
9 Power_On_Hours 0x0032 100 100 000 Old_age Always
- 704
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always
- 68
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always
- 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always
- 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always
- 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always
- 0 0 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always
- 0
190 Airflow_Temperature_Cel 0x0022 069 057 040 Old_age Always
- 31 (Min/Max 23/33)
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always
- 262
194 Temperature_Celsius 0x0022 031 016 000 Old_age Always
- 31 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 010 006 000 Old_age Always
- 201611737
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline
- 75h+17m+42.252s
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline
- 1749229928
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline
- 1409020289
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
--
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
https://bugs.launchpad.net/bugs/1143495
Title:
udisks reporting input/output error that seems to be nonsense
To manage notifications about this bug go to:
https://bugs.launchpad.net/libatasmart/+bug/1143495/+subscriptions
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
