Public bug reported:
Binary package hint: linux-source-2.6.22
The default Gutsy server install fails to correctly configure the two Ethernet
interfaces (one onboard, one Realtek card) on my hardware. I'm guessing its an
IRQ routing issue.
Setting pci=noacpi in the kernel boot parameters works around the
problem, but I lose the ACPI facilities.
The strange thing is that the default Feisty desktop install gets ACPI
right. I haven't tested the Gutsy desktop, but the Feisty server install
failed with what I assume is the same problem.
I am using the latest (and only) BIOS available for my hardware, which
is an HP Vectra XE310 series 2.
The relevant dmesg sections are as follows:
Gutsy server (failing)
[ 0.000000] ACPI: RSDP signature @ 0xC00F70B0 checksum 0
[ 0.000000] ACPI: RSDP 000F70B0, 0014 (r0 PTLTD )
[ 0.000000] ACPI: RSDT 1FCFAE82, 002C (r1 PTLTD RSDT 6040000 LTP
0)
[ 0.000000] ACPI: FACP 1FCFEF18, 0084 (r2 HP HPBDD_IV 6040000 PTL
1)
[ 0.000000] ACPI: DSDT 1FCFAEAE, 406A (r1 HP HPBDD_IV 6040000 MSFT
100000D)
[ 0.000000] ACPI: FACS 1FCFFFC0, 0040
[ 0.000000] ACPI: APIC 1FCFEF9C, 0064 (r1 PTLTD APIC 6040000 LTP
0)
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:11 APIC version 17
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 30000000 (gap:
20000000:df800000)
[ 0.000000] Built 1 zonelists. Total pages: 129667
[ 0.000000] Kernel command line:
root=UUID=aed2adfb-68a6-4646-9bd5-f2ff90b8503d ro quiet splash
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 1196.149 MHz processor.
[ 39.964144] Console: colour VGA+ 80x25
[ 39.965180] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 39.966297] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 39.999156] Memory: 506724k/522752k available (2047k kernel code, 15328k
reserved, 920k data, 364k init, 0k highmem)
[ 39.999177] virtual kernel memory layout:
[ 39.999179] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 39.999181] pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 39.999184] vmalloc : 0xe0800000 - 0xffbfe000 ( 499 MB)
[ 39.999187] lowmem : 0xc0000000 - 0xdfe80000 ( 510 MB)
[ 39.999189] .init : 0xc03eb000 - 0xc0446000 ( 364 kB)
[ 39.999192] .data : 0xc02ffcc6 - 0xc03e5f04 ( 920 kB)
[ 39.999194] .text : 0xc0100000 - 0xc02ffcc6 (2047 kB)
[ 39.999200] Checking if this processor honours the WP bit even in supervisor
mode... Ok.
[ 39.999276] SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1,
Nodes=1
[ 40.149287] Calibrating delay using timer specific routine.. 2393.63
BogoMIPS (lpj=11968179)
[ 40.149341] Security Framework v1.0.0 initialized
[ 40.149358] SELinux: Disabled at boot.
[ 40.149387] Mount-cache hash table entries: 512
[ 40.149630] CPU: After generic identify, caps: 0383fbff 00000000 00000000
00000000 00000000 00000000 00000000
[ 40.149649] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 40.149654] CPU: L2 cache: 256K
[ 40.149660] CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040
00000000 00000000 00000000
[ 40.149678] Compat vDSO mapped to ffffe000.
[ 40.149701] Checking 'hlt' instruction... OK.
[ 40.189421] SMP alternatives: switching to UP code
[ 40.189696] Freeing SMP alternatives: 11k freed
[ 40.190178] Early unpacking initramfs... done
[ 40.702801] ACPI: Core revision 20070126
[ 40.702989] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not
found.
[ 41.163169] ACPI Error (hwacpi-0142): Hardware did not change modes
[20070126]
[ 41.163181] ACPI Error (evxfevnt-0086): Could not transition to ACPI mode
[20070126]
[ 41.163189] ACPI Warning (utxface-0139): AcpiEnable failed [20070126]
[ 41.163196] ACPI: Unable to enable ACPI
[ 41.163306] CPU0: Intel(R) Pentium(R) III CPU 1200MHz stepping 01
[ 41.163350] Total of 1 processors activated (2393.63 BogoMIPS).
[ 41.163487] ENABLING IO-APIC IRQs
[ 41.163693] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 41.379247] Brought up 1 CPUs
[ 41.379479] Booting paravirtualized kernel on bare hardware
[ 41.379578] Time: 0:44:22 Date: 10/04/107
[ 41.379636] NET: Registered protocol family 16
[ 41.379838] EISA bus registered
[ 41.380616] PCI: PCI BIOS revision 2.10 entry at 0xfd9b8, last bus=1
[ 41.380621] PCI: Using configuration type 1
[ 41.380625] Setting up standard PCI resources
[ 41.385327] ACPI: Interpreter disabled.
[ 41.385337] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 41.385354] pnp: PnP ACPI: disabled
[ 41.385363] PnPBIOS: Scanning system for PnP BIOS support...
[ 41.385407] PnPBIOS: Found PnP BIOS installation structure at 0xc00f70e0
[ 41.385413] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xacce, dseg 0x400
[ 41.388890] PnPBIOS: 20 nodes reported by PnP BIOS; 20 recorded by driver
[ 41.389023] PCI: Probing PCI hardware
[ 41.389042] PCI: Probing PCI hardware (bus 00)
[ 41.389365] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[ 41.389375] PCI quirk: region 1180-11bf claimed by ICH4 GPIO
[ 41.389973] PCI: Transparent bridge - 0000:00:1e.0
[ 41.391090] PCI: Using IRQ router PIIX/ICH [8086/2440] at 0000:00:1f.0
[ 41.391107] PCI BIOS passed nonexistent PCI bus 0!
[ 41.391116] PCI BIOS passed nonexistent PCI bus 0!
[ 41.391121] PCI BIOS passed nonexistent PCI bus 0!
[ 41.391126] PCI BIOS passed nonexistent PCI bus 0!
[ 41.391131] PCI BIOS passed nonexistent PCI bus 0!
[ 41.391135] PCI BIOS passed nonexistent PCI bus 1!
[ 41.391139] PCI BIOS passed nonexistent PCI bus 0!
[ 41.391143] PCI BIOS passed nonexistent PCI bus 1!
[ 41.391147] PCI BIOS passed nonexistent PCI bus 0!
[ 41.391151] PCI BIOS passed nonexistent PCI bus 1!
[ 41.391155] PCI BIOS passed nonexistent PCI bus 0!
[ 41.391159] PCI BIOS passed nonexistent PCI bus 1!
[ 41.391163] PCI BIOS passed nonexistent PCI bus 0!
[ 41.394195] NET: Registered protocol family 8
[ 41.394200] NET: Registered protocol family 20
[ 41.394220] NetLabel: Initializing
[ 41.394223] NetLabel: domain hash size = 128
[ 41.394226] NetLabel: protocols = UNLABELED CIPSOv4
[ 41.394257] NetLabel: unlabeled traffic allowed by default
[ 41.394478] pnp: 00:00: iomem range 0xfff00000-0xffffffff could not be
reserved
[ 41.394485] pnp: 00:00: iomem range 0xf8000000-0xfbffffff has been reserved
[ 41.394500] pnp: 00:02: iomem range 0x0-0x9ffff could not be reserved
[ 41.394506] pnp: 00:02: iomem range 0xe4000-0xfffff could not be reserved
[ 41.394511] pnp: 00:02: iomem range 0x100000-0x1fe7ffff could not be reserved
[ 41.394531] pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved
[ 41.394537] pnp: 00:0b: ioport range 0x1000-0x105f has been reserved
[ 41.394543] pnp: 00:0b: ioport range 0x1060-0x107f has been reserved
[ 41.394549] pnp: 00:0b: ioport range 0x1180-0x11bf has been reserved
[ 41.394561] pnp: 00:0d: iomem range 0xe0000-0xe3fff has been reserved
[ 41.394573] pnp: 00:0e: iomem range 0xdf000-0xdffff has been reserved
[ 41.394586] pnp: 00:0f: iomem range 0xcc600-0xcffff has been reserved
[ 41.399189] Time: tsc clocksource has been installed.
[ 41.425231] PCI: Bridge: 0000:00:1e.0
[ 41.425237] IO window: 2000-2fff
[ 41.425244] MEM window: ec100000-ec1fffff
[ 41.425251] PREFETCH window: f4000000-f40fffff
[ 41.425271] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 41.425304] NET: Registered protocol family 2
[ 41.499271] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 41.499400] TCP established hash table entries: 16384 (order: 5, 196608
bytes)
[ 41.500140] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 41.500776] TCP: Hash tables configured (established 16384 bind 16384)
[ 41.500783] TCP reno registered
[ 41.529519] checking if image is initramfs...<6>Switched to high resolution
mode on CPU 0
[ 41.947075] it is
[ 42.493159] Freeing initrd memory: 6917k freed
[ 42.494126] audit: initializing netlink socket (disabled)
[ 42.494161] audit(1194137063.290:1): initialized
[ 42.498588] VFS: Disk quotas dquot_6.5.1
[ 42.498775] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 42.499050] io scheduler noop registered
[ 42.499056] io scheduler anticipatory registered
[ 42.499102] io scheduler deadline registered (default)
[ 42.499160] io scheduler cfq registered
[ 42.499192] Boot video device is 0000:00:02.0
[ 42.499534] isapnp: Scanning for PnP cards...
[ 42.856120] isapnp: No Plug & Play device found
[ 42.938248] Real Time Clock Driver v1.12ac
[ 42.938406] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
enabled
[ 42.938530] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 42.940573] 00:11: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 42.942144] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024
blocksize
[ 42.942631] input: Macintosh mouse button emulation as /class/input/input0
[ 42.942827] PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
[ 42.946727] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 42.946743] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 42.947166] mice: PS/2 mouse device common for all mice
[ 42.947400] EISA: Probing bus 0 at eisa.0
[ 42.947418] Cannot allocate resource for EISA slot 1
[ 42.947424] Cannot allocate resource for EISA slot 2
[ 42.947461] EISA: Detected 0 cards.
[ 42.947663] TCP cubic registered
[ 42.947701] NET: Registered protocol family 1
[ 42.947760] Using IPI No-Shortcut mode
[ 42.947964] Magic number: 15:11:708
[ 42.949409] Freeing unused kernel memory: 364k freed
[ 42.969174] input: AT Translated Set 2 keyboard as /class/input/input1
[ 43.284898] AppArmor: AppArmor initialized<5>audit(1194137063.790:2):
type=1505 info="AppArmor initialized" pid=1013
[ 43.298497] fuse init (API version 7.8)
[ 43.309499] Failure registering capabilities with primary security module.
[ 43.410566] thermal: Unknown symbol acpi_processor_set_thermal_limit
[ 44.770407] SCSI subsystem initialized
[ 44.801521] libata version 2.21 loaded.
[ 44.805382] usbcore: registered new interface driver usbfs
[ 44.805433] usbcore: registered new interface driver hub
[ 44.805489] usbcore: registered new device driver usb
[ 44.812982] ata_piix 0000:00:1f.1: version 2.11
[ 44.813075] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 44.815696] scsi0 : ata_piix
[ 44.815814] scsi1 : ata_piix
[ 44.815868] ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma
0x00011800 irq 14
[ 44.815875] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma
0x00011808 irq 15
[ 44.816042] USB Universal Host Controller Interface driver v3.0
[ 45.029235] ata1.00: ATA-6: SAMSUNG SV4002H, QP100-07, max UDMA/100
[ 45.029246] ata1.00: 78242976 sectors, multi 16: LBA
[ 45.029261] ata1.01: ATA-3: WDC AC34000L, 32.41N37, max UDMA/33
[ 45.029266] ata1.01: 7814016 sectors, multi 16: LBA
[ 45.069280] ata1.00: configured for UDMA/100
[ 45.109045] ata1.01: configured for UDMA/33
[ 45.131788] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 45.135025] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 45.135034] e100: Copyright(c) 1999-2006 Intel Corporation
[ 45.372199] FDC 0 is a National Semiconductor PC87306
[ 45.429080] ata2.00: ATAPI: LTN486S, YKS4, max UDMA/33, CDB intr
[ 45.609067] ata2.00: configured for UDMA/33
[ 45.609332] scsi 0:0:0:0: Direct-Access ATA SAMSUNG SV4002H QP10
PQ: 0 ANSI: 5
[ 45.610234] scsi 0:0:1:0: Direct-Access ATA WDC AC34000L 32.4
PQ: 0 ANSI: 5
[ 45.610633] scsi 1:0:0:0: CD-ROM LITEON CD-ROM LTN486S YKS4
PQ: 0 ANSI: 5
[ 45.611002] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 45.611009] uhci_hcd 0000:00:1f.2: UHCI Host Controller
[ 45.611286] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus
number 1
[ 45.611326] uhci_hcd 0000:00:1f.2: irq 9, io base 0x00001820
[ 45.611582] usb usb1: configuration #1 chosen from 1 choice
[ 45.611640] hub 1-0:1.0: USB hub found
[ 45.611654] hub 1-0:1.0: 2 ports detected
[ 45.640917] sd 0:0:0:0: [sda] 78242976 512-byte hardware sectors (40060 MB)
[ 45.640945] sd 0:0:0:0: [sda] Write Protect is off
[ 45.640950] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 45.640981] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 45.641093] sd 0:0:0:0: [sda] 78242976 512-byte hardware sectors (40060 MB)
[ 45.641110] sd 0:0:0:0: [sda] Write Protect is off
[ 45.641115] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 45.641143] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 45.641151] sda: sda1 sda2 < sda5 >
[ 45.673960] sd 0:0:0:0: [sda] Attached SCSI disk
[ 45.675411] sd 0:0:1:0: [sdb] 7814016 512-byte hardware sectors (4001 MB)
[ 45.675438] sd 0:0:1:0: [sdb] Write Protect is off
[ 45.675443] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 45.675474] sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled,
doesn't support DPO or FUA
[ 45.675582] sd 0:0:1:0: [sdb] 7814016 512-byte hardware sectors (4001 MB)
[ 45.675599] sd 0:0:1:0: [sdb] Write Protect is off
[ 45.675604] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 45.675632] sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled,
doesn't support DPO or FUA
[ 45.675639] sdb: sdb1 sdb2 < sdb5 >
[ 45.716263] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 45.719071] PCI: Setting latency timer of device 0000:00:1f.4 to 64
[ 45.719084] uhci_hcd 0000:00:1f.4: UHCI Host Controller
[ 45.719133] uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus
number 2
[ 45.719173] uhci_hcd 0000:00:1f.4: irq 11, io base 0x00001840
[ 45.719391] usb usb2: configuration #1 chosen from 1 choice
[ 45.719453] hub 2-0:1.0: USB hub found
[ 45.719471] hub 2-0:1.0: 2 ports detected
[ 45.735693] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 45.735766] sd 0:0:1:0: Attached scsi generic sg1 type 0
[ 45.735806] sr 1:0:0:0: Attached scsi generic sg2 type 5
[ 45.788839] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 45.788854] Uniform CD-ROM driver Revision: 3.20
[ 45.788985] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 45.829248] 8139cp 0000:01:01.0: This (id 10ec:8139 rev 10) is not an 8139C+
compatible chip
[ 45.829308] 8139cp 0000:01:01.0: Try the "8139too" driver instead.
[ 45.834606] PCI: Enabling device 0000:01:08.0 (0000 -> 0003)
[ 45.834622] PCI BIOS passed nonexistent PCI bus 1!
[ 45.834627] PCI BIOS passed nonexistent PCI bus 0!
[ 45.834631] PCI: No IRQ known for interrupt pin A of device 0000:01:08.0.
Probably buggy MP table.
[ 45.834718] PCI: Setting latency timer of device 0000:01:08.0 to 64
[ 45.857360] e100: eth0: e100_probe: addr 0xec101000, irq 0, MAC addr
00:04:23:16:89:2D
[ 45.857904] 8139too Fast Ethernet driver 0.9.28
[ 45.858376] eth1: RealTek RTL8139 at 0xe08ca000, 00:e0:4c:0a:3a:99, IRQ 9
[ 45.858382] eth1: Identified 8139 chip type 'RTL-8100B/8139D'
[ 46.889008] Attempting manual resume
[ 46.889016] swsusp: Resume From Partition 8:5
[ 46.889019] PM: Checking swsusp image.
[ 46.889396] PM: Resume from disk failed.
[ 46.962907] kjournald starting. Commit interval 5 seconds
[ 46.962935] EXT3-fs: mounted filesystem with ordered data mode.
[ 53.345424] eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
[ 56.950077] NET: Registered protocol family 10
...
[ 71.145977] NETDEV WATCHDOG: eth1: transmit timed out
[ 74.145622] eth1: Transmit timeout, status 0d 0004 c07f media 10.
[ 74.145632] eth1: Tx queue start entry 4 dirty entry 0.
[ 74.145638] eth1: Tx descriptor 0 is 0008a04e. (queue head)
[ 74.145643] eth1: Tx descriptor 1 is 0008a05a.
[ 74.145647] eth1: Tx descriptor 2 is 0008a046.
[ 74.145652] eth1: Tx descriptor 3 is 0008a05a.
[ 74.145669] eth1: link up, 100Mbps, full-duplex, lpa 0xC5E1
The matching section of the Feisty desktop dmesg is:
[ 0.000000] ACPI: RSDP (v000 PTLTD ) @
0x000f70b0
[ 0.000000] ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @
0x1fcfae82
[ 0.000000] ACPI: FADT (v002 HP HPBDD_IV 0x06040000 PTL 0x00000001) @
0x1fcfef18
[ 0.000000] ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @
0x1fcfef9c
[ 0.000000] ACPI: DSDT (v001 HP HPBDD_IV 0x06040000 MSFT 0x0100000d) @
0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:11 APIC version 17
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 30000000 (gap:
20000000:df800000)
[ 0.000000] Detected 1196.146 MHz processor.
[ 14.016009] Built 1 zonelists. Total pages: 129667
[ 14.016015] Kernel command line:
root=UUID=2edc601a-03c3-4ab1-8a33-c4547eb01997 ro quiet splash
[ 14.016360] mapped APIC to ffffd000 (fee00000)
[ 14.016366] mapped IOAPIC to ffffc000 (fec00000)
[ 14.016374] Enabling fast FPU save and restore... done.
[ 14.016379] Enabling unmasked SIMD FPU exception support... done.
[ 14.016394] Initializing CPU#0
[ 14.016482] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 14.018378] Console: colour VGA+ 80x25
[ 14.019519] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 14.020870] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 14.053445] Memory: 507188k/522752k available (1993k kernel code, 14956k
reserved, 900k data, 328k init, 0k highmem)
[ 14.053465] virtual kernel memory layout:
[ 14.053467] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 14.053469] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 14.053472] vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
[ 14.053474] lowmem : 0xc0000000 - 0xdfe80000 ( 510 MB)
[ 14.053477] .init : 0xc03d9000 - 0xc042b000 ( 328 kB)
[ 14.053479] .data : 0xc02f2429 - 0xc03d36d4 ( 900 kB)
[ 14.053481] .text : 0xc0100000 - 0xc02f2429 (1993 kB)
[ 14.053487] Checking if this processor honours the WP bit even in supervisor
mode... Ok.
[ 14.132478] Calibrating delay using timer specific routine.. 2394.07
BogoMIPS (lpj=4788154)
[ 14.132557] Security Framework v1.0.0 initialized
[ 14.132577] SELinux: Disabled at boot.
[ 14.132609] Mount-cache hash table entries: 512
[ 14.132870] CPU: After generic identify, caps: 0383fbff 00000000 00000000
00000000 00000000 00000000 00000000
[ 14.132889] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 14.132894] CPU: L2 cache: 256K
[ 14.132899] CPU: After all inits, caps: 0383fbff 00000000 00000000 00000040
00000000 00000000 00000000
[ 14.132923] Compat vDSO mapped to ffffe000.
[ 14.132931] Remapping vsyscall page to ffffe000
[ 14.132949] Checking 'hlt' instruction... OK.
[ 14.148604] SMP alternatives: switching to UP code
[ 14.148872] Freeing SMP alternatives: 11k freed
[ 14.149202] Early unpacking initramfs... done
[ 14.694562] ACPI: Core revision 20060707
[ 14.695432] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found,
using machine DSDT.
[ 14.699492] CPU0: Intel(R) Pentium(R) III CPU 1200MHz stepping 01
[ 14.699542] Total of 1 processors activated (2394.07 BogoMIPS).
[ 14.699681] ENABLING IO-APIC IRQs
[ 14.699891] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 14.844511] Brought up 1 CPUs
[ 14.844951] Booting paravirtualized kernel on bare hardware
[ 14.845078] Time: 7:28:50 Date: 10/03/107
[ 14.845141] NET: Registered protocol family 16
[ 14.845337] EISA bus registered
[ 14.845346] ACPI: bus type pci registered
[ 14.846119] PCI: PCI BIOS revision 2.10 entry at 0xfd9b8, last bus=1
[ 14.846123] PCI: Using configuration type 1
[ 14.846127] Setting up standard PCI resources
[ 14.853829] ACPI: Interpreter enabled
[ 14.853841] ACPI: Using IOAPIC for interrupt routing
[ 14.854473] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 14.854486] PCI: Probing PCI hardware (bus 00)
[ 14.856702] Boot video device is 0000:00:02.0
[ 14.856810] PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
[ 14.856817] PCI quirk: region 1180-11bf claimed by ICH4 GPIO
[ 14.857345] PCI: Transparent bridge - 0000:00:1e.0
[ 14.857376] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 14.860824] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 14.861226] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 14.861606] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[ 14.861987] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *9 10 11 12 14 15)
[ 14.862408] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 7 9 10 11 12 14 15)
[ 14.862787] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15)
*0, disabled.
[ 14.863166] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12 14 15)
*0, disabled.
[ 14.863552] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 14.889569] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
[ 14.890888] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 14.890927] pnp: PnP ACPI init
[ 14.936410] pnp: PnP ACPI: found 12 devices
[ 14.936423] PnPBIOS: Disabled by ACPI PNP
[ 14.936624] PCI: Using ACPI for IRQ routing
[ 14.936631] PCI: If a device doesn't work, try "pci=routeirq". If it helps,
post a report
[ 14.939610] NET: Registered protocol family 8
[ 14.939614] NET: Registered protocol family 20
[ 14.941167] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
[ 14.941192] PCI: Bridge: 0000:00:1e.0
[ 14.941197] IO window: 2000-2fff
[ 14.941204] MEM window: ec100000-ec1fffff
[ 14.941211] PREFETCH window: f4000000-f40fffff
[ 14.941230] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 14.941291] NET: Registered protocol family 2
[ 14.980556] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 14.980711] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 14.981057] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 14.981264] TCP: Hash tables configured (established 16384 bind 8192)
[ 14.981270] TCP reno registered
[ 14.992742] checking if image is initramfs... it is
[ 16.004308] Freeing initrd memory: 6759k freed
[ 16.005403] audit: initializing netlink socket (disabled)
[ 16.005438] audit(1194074932.068:1): initialized
[ 16.005727] VFS: Disk quotas dquot_6.5.1
[ 16.005776] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 16.005889] io scheduler noop registered
[ 16.005897] io scheduler anticipatory registered
[ 16.005901] io scheduler deadline registered
[ 16.005921] io scheduler cfq registered (default)
[ 16.006459] isapnp: Scanning for PnP cards...
[ 16.360304] isapnp: No Plug & Play device found
[ 16.425459] Real Time Clock Driver v1.12ac
[ 16.425540] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
enabled
[ 16.425692] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 16.427110] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 16.427580] mice: PS/2 mouse device common for all mice
[ 16.428769] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024
blocksize
[ 16.429274] input: Macintosh mouse button emulation as /class/input/input0
[ 16.429345] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 16.429355] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
[ 16.429738] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64
irq 1,12
[ 16.433395] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 16.433412] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 16.433729] EISA: Probing bus 0 at eisa.0
[ 16.433751] Cannot allocate resource for EISA slot 1
[ 16.433756] Cannot allocate resource for EISA slot 2
[ 16.433784] EISA: Detected 0 cards.
[ 16.463944] TCP cubic registered
[ 16.463959] NET: Registered protocol family 1
If I do an lspci -vvnn on the working Feisty install, I get:
lspci -vvnn
00:00.0 Host bridge [0600]: Intel Corporation 82815 815 Chipset Host Bridge and
Memory Controller Hub [8086:1130] (rev 04)
Subsystem: Hewlett-Packard Company Unknown device [103c:1297]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [88] Vendor Specific Information
00:02.0 VGA compatible controller [0300]: Intel Corporation 82815 CGC [Chipset
Graphics Controller] [8086:1132] (rev 04) (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company Unknown device [103c:1297]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at ec000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00002000-00002fff
Memory behind bridge: ec100000-ec1fffff
Prefetchable memory behind bridge: f4000000-f40fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801BA ISA Bridge (LPC)
[8086:2440] (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801BA IDE U100 [8086:244b]
(rev 05) (prog-if 80 [Master])
Subsystem: Hewlett-Packard Company Unknown device [103c:1297]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at 1800 [size=16]
00:1f.2 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB (Hub #1)
[8086:2442] (rev 05) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:1297]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 18
Region 4: I/O ports at 1820 [size=32]
00:1f.3 SMBus [0c05]: Intel Corporation 82801BA/BAM SMBus [8086:2443] (rev 05)
Subsystem: Hewlett-Packard Company Unknown device [103c:1297]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 1810 [size=16]
00:1f.4 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB (Hub #2)
[8086:2444] (rev 05) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device [103c:1297]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at 1840 [size=32]
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801BA/BAM AC'97
Audio [8086:2445] (rev 05)
Subsystem: Hewlett-Packard Company Unknown device [103c:126e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 1880 [size=64]
01:00.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video
Capture [109e:036e] (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series [0070:13eb]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 132 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f4000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture
[109e:0878] (rev 11)
Subsystem: Hauppauge computer works Inc. WinTV Series [0070:13eb]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f4001000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:01.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139 [10ec:8139]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at ec100000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at f4010000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:08.0 Ethernet controller [0200]: Intel Corporation 82801BA/BAM/CA/CAM
Ethernet Controller [8086:2449] (rev 03)
Subsystem: Intel Corporation EtherExpress PRO/100 VE [8086:3013]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 14000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at ec101000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 2400 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
The matching Ethernet controller entries for Gutsy seem to have different IRQs
assigned:
01:01.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139 [10ec:8139]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at ec100000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at f4010000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:08.0 Ethernet controller [0200]: Intel Corporation 82801BA/BAM/CA/CAM
Ethernet Controller [8086:2449] (rev 03)
Subsystem: Intel Corporation EtherExpress PRO/100 VE [8086:3013]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min, 14000ns max)
Interrupt: pin A routed to IRQ 0
Region 0: Memory at ec101000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 2400 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
** Affects: linux-source-2.6.22 (Ubuntu)
Importance: Undecided
Status: New
--
ACPI misconfigures ethernet on server not desktop
https://bugs.launchpad.net/bugs/159875
You received this bug notification because you are a member of Ubuntu
Bugs, which is the bug contact for Ubuntu.
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
