* the output of $sudo smartctl -a /dev/hda
$ sudo smartctl -a /dev/hda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Travelstar 80GN family
Device Model: IC25N060ATMR04-0
Serial Number: MRG308K3HY50SH
Firmware Version: MO3OAD4A
User Capacity: 60,011,642,880 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 3a
Local Time is: Sun Nov 4 08:59:05 2007 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 53) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always
- 0
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline
- 0
3 Spin_Up_Time 0x0007 170 170 033 Pre-fail Always
- 1
4 Start_Stop_Count 0x0012 099 099 000 Old_age Always
- 2133
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always
- 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline
- 0
9 Power_On_Hours 0x0012 066 066 000 Old_age Always
- 15100
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always
- 1606
191 G-Sense_Error_Rate 0x000a 096 096 000 Old_age Always
- 589824
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 86
193 Load_Cycle_Count 0x0012 055 055 000 Old_age Always
- 455567
194 Temperature_Celsius 0x0002 125 125 000 Old_age Always
- 44 (Lifetime Min/Max 4/66)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always
- 11
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always
- 4
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always
- 0
SMART Error Log Version: 1
ATA Error Count: 14 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 14 occurred at disk power-on lifetime: 8465 hours (352 days + 17 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 1e 12 e6 ef
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
fe a2 01 1e 12 06 e0 02 00:32:36.600 [VENDOR SPECIFIC]
fe a2 01 1d 12 06 e0 02 00:32:36.500 [VENDOR SPECIFIC]
fe a2 01 1c 12 06 e0 02 00:32:36.500 [VENDOR SPECIFIC]
fe a2 01 1b 12 06 e0 02 00:32:36.500 [VENDOR SPECIFIC]
fe a2 01 1a 12 06 e0 02 00:32:36.500 [VENDOR SPECIFIC]
Error 13 occurred at disk power-on lifetime: 8465 hours (352 days + 17 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 1e 12 e6 ef
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
fe a2 01 1e 12 06 e0 02 00:32:26.600 [VENDOR SPECIFIC]
fe a2 01 1d 12 06 e0 02 00:32:26.600 [VENDOR SPECIFIC]
fe a2 01 1c 12 06 e0 02 00:32:26.600 [VENDOR SPECIFIC]
fe a2 01 1b 12 06 e0 02 00:32:26.600 [VENDOR SPECIFIC]
fe a2 01 1a 12 06 e0 02 00:32:26.600 [VENDOR SPECIFIC]
Error 12 occurred at disk power-on lifetime: 6558 hours (273 days + 6 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 be 3b 0e e1 Error: UNC 1 sectors at LBA = 0x010e3bbe = 17710014
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 d8 08 b7 3b 0e e1 00 00:01:26.800 READ DMA
c8 d8 08 7f d8 fc e5 00 00:01:26.800 READ DMA
c8 d8 0d 37 4a ec e2 00 00:01:26.800 READ DMA
c8 d8 40 f7 49 ec e2 00 00:01:26.800 READ DMA
c8 d8 40 b7 49 ec e2 00 00:01:26.800 READ DMA
Error 11 occurred at disk power-on lifetime: 6558 hours (273 days + 6 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 04 bb 3b 0e e1 Error: UNC 4 sectors at LBA = 0x010e3bbb = 17710011
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 d8 08 b7 3b 0e e1 00 00:01:21.700 READ DMA
ca d8 20 d7 73 ec e2 00 00:01:21.700 WRITE DMA
ca d8 08 c7 73 ec e2 00 00:01:21.700 WRITE DMA
ca d8 10 ff 73 ec e2 00 00:01:21.700 WRITE DMA
c8 d8 08 b7 3b 0e e1 00 00:01:18.100 READ DMA
Error 10 occurred at disk power-on lifetime: 6558 hours (273 days + 6 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 04 bb 3b 0e e1 Error: UNC 4 sectors at LBA = 0x010e3bbb = 17710011
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 d8 08 b7 3b 0e e1 00 00:01:18.100 READ DMA
ca d8 08 77 88 df e0 00 00:01:18.100 WRITE DMA
ca d8 08 8f 88 df e0 00 00:01:18.100 WRITE DMA
ca d8 10 bf 61 e1 e0 00 00:01:18.100 WRITE DMA
c8 d8 08 b7 3b 0e e1 00 00:01:11.800 READ DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum.
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
* the age of your disk
3 years old
---Things I don't know how to check---
* whether you have enabled laptop-mode
* an estimate of the total hours your disk has been running since you started
using it (to compare to Power_on_Hours because that value might be off)
* any other information you consider relevant
---Things I will check later---
* an estimate of the average increase of Load_Cycle_Count during one hour and
during one day on AC
--
Hard drive spindown should be configurable
https://bugs.launchpad.net/bugs/17216
You received this bug notification because you are a member of Ubuntu
Bugs, which is a direct subscriber.
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
