** Description changed: - Upstream raspberrypi patchset 2020-06-10 - Ported from the following raspberrypi branch: - rpi-5.4.y + Ported from the following raspberrypi branch: + rpi-5.4.y from https://github.com/raspberrypi/linux.git + + w1_therm: remove redundant assignments to variable ret + w1_therm: Free the correct variable + w1_therm: adding bulk read support to trigger multiple conversion on bus + w1_therm: adding alarm sysfs entry + w1_therm: optimizing temperature read timings + w1_therm: adding eeprom sysfs entry + w1_therm: adding resolution sysfs entry + w1_therm: adding ext_power sysfs entry + w1_therm: fix reset_select_slave during discovery + w1_therm: adding code comments and code reordering + overlays: Update upstream overlays after vc4-kms-v3d change + overlays: i2c-gpio: Avoid open-drain warnings + Revert "overlays: gpio-keys: Avoid open-drain warnings" + snd_bcm2835: disable HDMI audio when vc4 is used (#3640) + vc4: cec: Restore cec physical address on reconnect + staging: vchiq_arm: Use g_dma_dev for dma_unmap_sg + vc4: Set driver_name for card + configs: Add SND_SOC_MAX98357A=m + Add Micro Crystal RV-1805 to i2c-rtc overlays + media: bcm2835-isp: fix bytes per line calculations for some image formats + overlays: i2c-rtc-gpio: Fix trickle-resistor-ohms param + net: rtl8192cu: fix gcc misleading whitespace warning + overlays: Add spi0 overlay to support sc16is752 + overlays: gpio-shutdown: Add information for Raspberry Pi 1 Model B rev 1 + overlays: gpio-shutdown: Add information for SysV init / inittab + overlays: i2c-rtc: Fix trickle-resistor-ohms param + brcmfmac: BCM43436 needs dedicated firmware + configs: Build HWMON core into kernel + configs: Switch to upstream thermal sensor for RPi 4 - BCM2711_THERMAL + ARM: dts: bcm2711-rpi: Remove downstream thermal sensor node + Revert "thermal: brcmstb_thermal: Add BCM2838 support" + Revert "thermal: brcmstb_thermal: Correct SoC name" + ARM: configs: Build BCM2711 thermal as module + ARM: dts: bcm2711: Enable thermal + thermal: Add BCM2711 thermal driver + dt-bindings: Add Broadcom AVS RO thermal + media: bcm2835-unicam: change minimum number of vb2_queue buffers to 1 + Revert "zswap: Uncross module parameter setting functions" + ARM: dts: Update for new VCHIQ BCM2711 DMA support + staging: vchiq_arm: Clean up 40-bit DMA support + media: i2c: imx477: Return correct result on sensor id verification + drm/vc4: Add FKMS as an acceptable node for dma ranges. + drm/vc4: Adopt the dma configuration from the HVS or V3D component + configs: Add ZSWAP=y, ZBUD=m, Z3FOLD=m + zswap: Defer zswap initialisation + zswap: Uncross module parameter setting functions + media: bcm2835-unicam: Retain packing information on G_FMT + Switch to snd_soc_dai_set_bclk_ratio + overlays: Fix audio parameter of vc4-kms-v3d + configs: Restore missing NF_TABLES settings + staging:vc04_services: bcm2835-camera: Request headers with I-frame + staging:vc04_services: bcm2835-codec: Avoid fragmenting buffers + staging:vc04_services: bcm2835-codec: Request headers with I-frame + staging: vc04_services: mmal-vchiq: Update parameters list + drm/vc4: Fix VIC usage with Broadcast RGB + sc16is7xx: Fix for hardware flow control + media: bcm2835-unicam: Always service interrupts + configs: Use the upstream cpufreq driver + configs: Include the firmware-clocks driver + ARM: dts: Enable firmware-clocks on all Pis + defconfig: Add CMA and system dma-heaps to the config + dma-heap: Make the symbol 'dma_heap_ioctl_cmds' static + dma-buf: fix resource leak on -ENOTTY error return path + dma-buf: heaps: Remove redundant heap identifier from system heap name + dma-buf: heaps: Use _IOCTL_ for userspace IOCTL identifier + kselftests: Add dma-heap test + dma-buf: heaps: Add CMA heap to dmabuf heaps + dma-buf: heaps: Add system heap to dmabuf heaps + dma-buf: heaps: Add heap helpers + dma-buf: Add dma-buf heaps framework + udmabuf: fix dma-buf cpu access + udmabuf: implement begin_cpu_access/end_cpu_access hooks + udmabuf: separate out creating/destroying scatter-table + udmabuf: add a pointer to the miscdevice in dma-buf private data + udmabuf: use cache_sgt_mapping option + udmabuf: Remove deleted map/unmap handlers. + configs: Add imx477 sensor driver to all Raspberry Pi defconfigs + media: i2c: imx477: Add support for adaptive frame control + media: i2c: Add driver for Sony IMX477 sensor + dtoverlays: Add IMX477 sensor overlay + dt-bindings: media: i2c: Add IMX477 CMOS sensor binding + raspberrypi: dts: Switch to discrete ALSA devices + overlays: Move "fixed-clock" nodes to the root + overlays: tc358743: Use intra-overlay fragments
-- You received this bug notification because you are a member of Ubuntu Bugs, which is subscribed to Ubuntu. https://bugs.launchpad.net/bugs/1882930 Title: focal/linux-raspi: Upstream raspberrypi patchset 2020-06-10 To manage notifications about this bug go to: https://bugs.launchpad.net/ubuntu/+source/linux-raspi/+bug/1882930/+subscriptions -- ubuntu-bugs mailing list [email protected] https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
