Public bug reported:
Server: HPE BL460c Gen9
Network: HP FlexFabric 10Gb 2-port 536FLB Adapter (Broadcom/Qlogic Net Extreme
II 10/20GBE)
Using ubuntu 20.04.2 with linux kernel 5.4.0-80 all functionality worked
however upon upgrades via apt to 20.04.3 which uses linux kernel
5.4.0-81, ubuntu is unable to load the drivers for the network device.
Below is the output for both kernels when the system is booted.
###################################
##### Kernel 5.4.0-80 working #####
###################################
ubuntu@server:$ dmesg | grep bnx2x
[ 6.648833] bnx2x: QLogic 5771x/578xx 10/20-Gigabit Ethernet Driver bnx2x
1.713.36-0 (2014/02/10)
[ 6.695219] bnx2x 0000:06:00.0: msix capability found
[ 6.719107] bnx2x 0000:06:00.0: part number 0-0-0-0
[ 7.112390] bnx2x 0000:06:00.0: 63.008 Gb/s available PCIe bandwidth (8 GT/s
x8 link)
[ 7.112504] bnx2x 0000:06:00.1: msix capability found
[ 7.112889] bnx2x 0000:06:00.1: part number 0-0-0-0
[ 7.320779] bnx2x 0000:06:00.1: 63.008 Gb/s available PCIe bandwidth (8 GT/s
x8 link)
[ 7.323549] bnx2x 0000:06:00.0 eno49: renamed from eth0
[ 7.343281] bnx2x 0000:06:00.1 eno50: renamed from eth1
[ 16.321102] bnx2x 0000:06:00.1 eno50: using MSI-X IRQs: sp 130 fp[0] 132
... fp[7] 139
[ 16.770833] bnx2x 0000:06:00.1 eno50: NIC Link is Up, 10000 Mbps full
duplex, Flow control: ON - receive & transmit
[ 17.136896] bnx2x 0000:06:00.0 eno49: using MSI-X IRQs: sp 120 fp[0] 122
... fp[7] 129
[ 17.526831] bnx2x 0000:06:00.0 eno49: NIC Link is Up, 10000 Mbps full
duplex, Flow control: ON - receive & transmit
ubuntu@server:$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eno49: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master
bond0 state UP group default qlen 1000
link/ether 9e:b2:88:1c:ea:40 brd ff:ff:ff:ff:ff:ff
3: eno50: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master
bond0 state UP group default qlen 1000
link/ether 9e:b2:88:1c:ea:40 brd ff:ff:ff:ff:ff:ff
4: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state
UP group default qlen 1000
link/ether 9e:b2:88:1c:ea:40 brd ff:ff:ff:ff:ff:ff
inet 10.0.0.68/24 brd 10.0.0.255 scope global bond0
valid_lft forever preferred_lft forever
inet6 fe80::9cb2:88ff:fe1c:ea40/64 scope link
valid_lft forever preferred_lft forever
ubuntu@server:$ sudo lshw -C network
*-network:0
description: Ethernet interface
product: BCM57840 NetXtreme II 10/20-Gigabit Ethernet
vendor: Broadcom Inc. and subsidiaries
physical id: 0
bus info: pci@0000:06:00.0
logical name: eno49
version: 11
serial: 9e:b2:88:1c:ea:40
size: 10Gbit/s
capacity: 10Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm vpd msix pciexpress bus_master cap_list rom ethernet
physical fibre 1000bt-fd 10000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=bnx2x
driverversion=1.713.36-0 storm 7.13.11.0 duplex=full firmware=mbi 7.18.77 bc
7.15.80 latency=0 link=yes multicast=yes port=fibre slave=yes speed=10Gbit/s
resources: irq:16 memory:94000000-947fffff memory:94800000-94ffffff
memory:95010000-9501ffff memory:92b00000-92b7ffff
*-network:1
description: Ethernet interface
product: BCM57840 NetXtreme II 10/20-Gigabit Ethernet
vendor: Broadcom Inc. and subsidiaries
physical id: 0.1
bus info: pci@0000:06:00.1
logical name: eno50
version: 11
serial: 9e:b2:88:1c:ea:40
size: 10Gbit/s
capacity: 10Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm vpd msix pciexpress bus_master cap_list rom ethernet
physical fibre 1000bt-fd 10000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=bnx2x
driverversion=1.713.36-0 storm 7.13.11.0 duplex=full firmware=mbi 7.18.77 bc
7.15.80 latency=0 link=yes multicast=yes port=fibre slave=yes speed=10Gbit/s
resources: irq:17 memory:93000000-937fffff memory:93800000-93ffffff
memory:95000000-9500ffff memory:92b80000-92bfffff
*-network
description: Ethernet interface
physical id: 1
logical name: bond0
serial: 9e:b2:88:1c:ea:40
size: 10Gbit/s
capabilities: ethernet physical
configuration: autonegotiation=off broadcast=yes driver=bonding
driverversion=3.7.1 duplex=full firmware=2 ip=10.0.0.68 link=yes master=yes
multicast=yes speed=10Gbit/s
###################################
##### Kernel 5.4.0-81 failure #####
###################################
ubuntu@server: $ dmesg | grep bnx2x
[ 6.605719] bnx2x: QLogic 5771x/578xx 10/20-Gigabit Ethernet Driver bnx2x
1.713.36-0 (2014/02/10)
[ 6.726579] bnx2X 0000:06:00.0: msix capability found
[ 6.741708] bnx2x 0000:06:00.0: part number 0-0-0-0
[ 7.319238] bnx2x: probe of 0000:06:00.0 failed with error -22
[ 7.319268] bnx2x 0000:06:00.1: msix capability found
[ 7.319475] bnx2x 0000:06:00.1: part number 0-0-0-0
[ 7.542188] bnx2x: probe of 0000:06:00.1 failed with error -22
ubuntu@server:$ ip a
1: lo: <LOOPBACK, UP, LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group
default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_ift forever preferred_ift forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: bond0: <NO-CARRIER, BROADCAST, MULTICAST, MASTER, UP> mtu 1500 qdisc noqueue
state DOWN group default qlen 1000
link/ether 9e:62:88:1c:ea:40 brd ff:ff:ff:ff:ff:ff
inet 10.0.0.68/24 brd 10.0.0.255 scope global bond0
valid_ift forever preferred_ift forever
ubuntu@server:~$ sudo lshw -C network
*-network:0 UNCLAIMED
description: Ethernet controller
product: BCM57840 NetXtreme II 10/20-Gigabit Ethernet
vendor: Broadcom Inc. and subsidiaries
physical id: 0
bus info: pcic0000:06:00.0
version: 11
width: 64 bits
clock: 33MHZ
capabilities: pm vpd msix pciexpress cap_list
configuration: latency=0
resources: memory:94000000-947fffff memory:94800000-94ffffff
memory:95010000-9501ffff memory: 92b00000-92b7ffff
*-network:1 UNCLAIMED
description: Ethernet controller
product: BCM57840 NetXtreme II 10/20-Gigabit Ethernet
vendor: Broadcom Inc. and subsidiaries
physical id: 0.1
bus info: pci@0000:06:00.1
version: 11
width: 64 bits
clock: 33MHZ
capabilities: pm vpd msix pciexpress cap_list
configuration: latency=0
resources: memory:93000000-937fffff memory:93800000-93ffffff
memory:95000000-9500ffff memory:92b80000-92bfffff
*-network
description: Ethernet interface
physical id: 1
logical name: bond0
serial: 9e:52:88:10:ea:40
capabilities: ethernet physical
configuration: autonegotiation=off broadcast=yes driver=bonding
driverversion=3.7.1 firmware=2 ip=10.0.0.68 link=no maste
r=yes multicast=yes
ubuntu@qs47:~$
ProblemType: Bug
DistroRelease: Ubuntu 20.04
Package: linux-image-5.4.0-81-generic 5.4.0-81.91
ProcVersionSignature: Ubuntu 5.4.0-80.90-generic 5.4.124
Uname: Linux 5.4.0-80-generic x86_64
AlsaDevices:
total 0
crw-rw---- 1 root audio 116, 1 Sep 3 08:01 seq
crw-rw---- 1 root audio 116, 33 Sep 3 08:01 timer
AplayDevices: Error: [Errno 2] No such file or directory: 'aplay'
ApportVersion: 2.20.11-0ubuntu27.18
Architecture: amd64
ArecordDevices: Error: [Errno 2] No such file or directory: 'arecord'
AudioDevicesInUse: Error: command ['fuser', '-v', '/dev/snd/seq',
'/dev/snd/timer'] failed with exit code 1:
CasperMD5CheckResult: pass
Date: Fri Sep 3 08:05:06 2021
InstallationDate: Installed on 2021-09-01 (1 days ago)
InstallationMedia: Ubuntu-Server 20.04.2 LTS "Focal Fossa" - Release amd64
(20210201.2)
IwConfig: Error: [Errno 2] No such file or directory: 'iwconfig'
MachineType: HP ProLiant BL460c Gen9
PciMultimedia:
ProcEnviron:
SHELL=/bin/bash
LANG=en_GB.UTF-8
TERM=xterm-256color
PATH=(custom, no user)
ProcFB: 0 mgag200drmfb
ProcKernelCmdLine: BOOT_IMAGE=/boot/vmlinuz-5.4.0-80-generic
root=/dev/mapper/maas-root ro
RelatedPackageVersions:
linux-restricted-modules-5.4.0-80-generic N/A
linux-backports-modules-5.4.0-80-generic N/A
linux-firmware 1.187.16
RfKill: Error: [Errno 2] No such file or directory: 'rfkill'
SourcePackage: linux
UpgradeStatus: No upgrade log present (probably fresh install)
dmi.bios.date: 10/16/2020
dmi.bios.vendor: HP
dmi.bios.version: I36
dmi.chassis.type: 28
dmi.chassis.vendor: HP
dmi.modalias:
dmi:bvnHP:bvrI36:bd10/16/2020:svnHP:pnProLiantBL460cGen9:pvr:cvnHP:ct28:cvr:
dmi.product.family: ProLiant
dmi.product.name: ProLiant BL460c Gen9
dmi.product.sku: 681844-B21
dmi.sys.vendor: HP
** Affects: linux (Ubuntu)
Importance: Undecided
Status: New
** Tags: amd64 apport-bug focal uec-images
--
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
https://bugs.launchpad.net/bugs/1942589
Title:
Ubuntu 5.4.0-81 stops bnx2x loading hardware
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1942589/+subscriptions
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
