HP EliteBook X G2i 14" (board name 8E86, BIOS Y90 Ver. 01.02.02 of 2026-07-14),
sensor OVTI05C1 on IPU7 (Panther Lake). Ubuntu 24.04.5, linux-hwe-7.0
7.0.0-42.42~24.04.1, CamHAL libcamhal-ipu75xa 0~git202604141000
(dell.archive.canonical.com noble/somerville), v4l2-relayd 0.1.2-0ubuntu3.1.
== Context
The HWE kernel source already contains the two SAUCE patches of this SRU (seen
in the Ubuntu diff of linux-hwe-7.0 7.0.0-42.42~24.04.1): ipu-bridge gives
OVTI05C1 480 MHz + 900 MHz, and int3472 raises the handshake delay from 25 ms to
50 ms. In the source this delay applies to every handshake-pin user, not only
OV05C10.
ov05c10 and intel-ipu7-psys are not loaded by default on this kernel. Here I
took ov05c10 from linux-main-modules-ipu6-7.0.0-42-generic and
intel-ipu7-psys from linux-main-modules-ipu7-7.0.0-42-generic and copied them to
/lib/modules/7.0.0-42-generic/updates/. The
linux-modules-ipu6/ipu7-generic-hwe-24.04
meta packages are not installed here, and I did not test installing them.
With that, the sensor binds ("bind ov05c10 1-0010 nlanes is 2 port is 0"),
psys probes, and CamHAL (icamerasrc) produces correct images.
== Problem
Some stream starts stall: no frame arrives, CamHAL logs repeatedly
"V4l2_device_cc: Poll: Device node fd N poll timeout" and "RequestThread: wait
event time out"; after the client is killed, dmesg shows
"intel_ipu7_isys: stream stop time out" / "stream close time out".
The next start works without reboot.
Separately, the psys firmware sometimes crashes on close, even when the capture
succeeded: "intel-ipu7-psys: group 3, code 15, detail: 5, 0",
"error state 3735879681", "fw not ready for shutdown, state 0xdead0001".
== Test
Same script each time, v4l2-relayd stopped:
icamerasrc num-buffers=30 ! video/x-raw,format=NV12,width=1280,height=720,
framerate=30/1 ! fakesink
with 5 s between runs. Only variable: intel_skl_int3472_discrete, stock
(50 ms) vs rebuilt from the same source with 200 ms.
- Stock, 50 ms: 2 stalled starts out of 80 (1/20 on Oct 30, 1/60 on Nov 9),
and 3 psys 0xdead0001 events during these two series.
- 200 ms: 0 stalls and 0 psys errors out of 95 starts (60 after a cold boot and
6 minutes without camera use, 30 through v4l2-relayd, 5 after 6 minutes idle).
- A 30-frame run takes 1.3 s at 200 ms vs 1.0 to 1.2 s at 50 ms.
The Nov 9 series (both values) followed a cold boot plus 6 minutes idle; the
Oct 30 series was not preceded by a controlled idle period.
Caveat: small samples. If the stall rate at 200 ms were the same ~2.5 %, 0 out
of 95 would happen about 9 % of the time. This is suggestive, not conclusive.
I did not try intermediate values, nor suspend/resume.
== Request
1. Consider 200 ms rather than 50 ms for OV05C10 (intel/ipu7-drivers issue #71
reports 200 ms, and a 7.4 kernel change for it).
2. Clarify how ov05c10 and intel-ipu7-psys are meant to reach noble HWE users;
today they are absent by default.
--
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
https://bugs.launchpad.net/bugs/2147409
Title:
Support additional 2888x1808@30fps 900MHz for OVTI05C1 camera sensor
To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/ipu6-drivers/+bug/2147409/+subscriptions
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs