** Description changed:

  [ Impact ]
  
-  * On the MediaTek MT8391-EVK (Genio 720/520 EVK), the alsa-ucm-conf
-    profile has three problems:
+  * On the MediaTek MT8391-EVK (Genio 720/520 EVK), the alsa-ucm-conf
+    profile has three problems:
  
-    - The Speaker device has only 1 channel, so the earphone output is
-      mono (center only).
+    - The Speaker device has only 1 channel, so the earphone output is
+      mono (center only).
  
-    - There are no hardware volume controls for Speaker, Headphones,
-      Headset and Mic1. The volume sliders do not change the hardware
-      gain and recordings from the analog microphone are very quiet.
+    - There are no hardware volume controls for Speaker, Headphones,
+      Headset and Mic1. The volume sliders do not change the hardware
+      gain and recordings from the analog microphone are very quiet.
  
-    - There is no device for the DisplayPort output on the USB-C port,
-      so no audio sink appears for an external monitor.
+    - There is no device for the DisplayPort output on the USB-C port,
+      so no audio sink appears for an external monitor.
  
-  * Upstream fixed the first two problems in 8275e1b and added the
-    DisplayPort output in 8048d93. Both commits are merged upstream but
-    are not in any release yet.
+  * Upstream fixed the first two problems in 8275e1b and added the
+    DisplayPort output in 8048d93. Both commits are merged upstream but
+    are not in any release yet.
  
-  * 8048d93 sets DPTX_OUT_MUX and HDMI_CH1_MUX only in the BootSequence,
-    which runs from "alsactl init". On a normal boot alsa-restore replays
-    the saved ALSA state instead. After an upgrade and a reboot:
+  * 8048d93 sets DPTX_OUT_MUX and HDMI_CH1_MUX only in the BootSequence,
+    which runs from "alsactl init". On a normal boot alsa-restore replays
+    the saved ALSA state instead. After an upgrade and a reboot:
  
-    - A saved DPTX_OUT_MUX=Disconnect makes the DisplayPort PCM
-      (hw:CardId,5) fail to open. WirePlumber then drops the whole HiFi
-      profile and only a dummy output and no inputs are left.
+    - A saved DPTX_OUT_MUX=Disconnect makes the DisplayPort PCM
+      (hw:CardId,5) fail to open. WirePlumber then drops the whole HiFi
+      profile and only a dummy output and no inputs are left.
  
-    - A saved HDMI_CH1_MUX=CH0 leaves the right DisplayPort channel
-      silent.
+    - A saved HDMI_CH1_MUX=CH0 leaves the right DisplayPort channel
+      silent.
  
-  * A third patch, the fix for 8048d93, sets the three DisplayPort muxes
-    from the HiFi verb EnableSequence, so they are applied every time
-    the profile is activated. 8048d93 must not be shipped without it.
+  * A third patch, the fix for 8048d93, sets the three DisplayPort muxes
+    from the HiFi verb EnableSequence, so they are applied every time
+    the profile is activated. 8048d93 must not be shipped without it.
  
  [ Test Plan ]
  
-  * Hardware used for the SRU verification:
-    - MediaTek Genio 720 EVK (MT8391-EVK) with display-dpoc.dtbo in
-      list_dtbo, and a DisplayPort monitor with speakers on the USB-C
-      DP port (directly or through a USB-C hub).
-    - Framework Laptop 13 (AMD Ryzen AI 300 Series), x86_64, for the
-      regression test on non-MT8391 hardware.
+  * Hardware used for the SRU verification:
+    - MediaTek Genio 720 EVK (MT8391-EVK) with display-dpoc.dtbo in
+      list_dtbo, and a DisplayPort monitor with speakers on the USB-C
+      DP port (directly or through a USB-C hub).
+    - Framework Laptop 13 (AMD Ryzen AI 300 Series), x86_64, for the
+      regression test on non-MT8391 hardware.
  
-  * Images on the Genio 720 EVK:
-    - Noble: the official Ubuntu 24.04 desktop image for Genio.
-    - Resolute and Stonking: there is no official Genio image for these
-      releases. A special arm64 image is prepared for the SRU
-      verification only, as was done for Questing in LP: #2139651.
+  * Images on the Genio 720 EVK:
+    - Noble: the official Ubuntu 24.04 desktop image for Genio.
+    - Resolute and Stonking: there is no official Genio image for these
+      releases. A special arm64 image is prepared for the SRU
+      verification only, as was done for Questing in LP: #2139651.
  
-  * The same steps are run on Noble, Resolute and Stonking, with the
-    package from -proposed installed. Results are posted as one comment
-    per release, with the installed version from
-    "apt-cache policy alsa-ucm-conf" and the command output.
+  * The same steps are run on Noble, Resolute and Stonking, with the
+    package from -proposed installed. Results are posted as one comment
+    per release, with the installed version from
+    "apt-cache policy alsa-ucm-conf" and the command output.
  
-  1. Enable -proposed, install the updated alsa-ucm-conf, reboot and log
-     in to the desktop.
+  1. Enable -proposed, install the updated alsa-ucm-conf, reboot and log
+     in to the desktop.
  
-  2. Run: wpctl status
-     Confirm these sinks: "DP output", "I2S output", "PCM output",
-     "Earphone speaker + Lineout speaker".
-     Confirm these sources: "I2S input", "PCM input",
-     "Digital microphone", "Analog microphone + Earphone microphone".
+  2. Run: wpctl status
+     Confirm these sinks: "DP output", "I2S output", "PCM output",
+     "Earphone speaker + Lineout speaker".
+     Confirm these sources: "I2S input", "PCM input",
+     "Digital microphone", "Analog microphone + Earphone microphone".
  
-  3. Stale state after a reboot:
-       sudo amixer -c0 cset name=DPTX_OUT_MUX Disconnect
-       sudo amixer -c0 cset name=HDMI_CH1_MUX CH0
-       sudo alsactl store
-     Reboot and log in. Confirm that the sinks and sources are the same
-     as in step 2, that
-       sudo amixer -c0 cget name=DPTX_OUT_MUX
-     shows Connect, that
-       sudo amixer -c0 cget name=HDMI_CH1_MUX
-     shows CH1, and that
-       journalctl --user -b -u wireplumber
-     has no "Error opening PCM device" line.
+  3. Stale state after a reboot:
+       sudo amixer -c0 cset name=DPTX_OUT_MUX Disconnect
+       sudo amixer -c0 cset name=HDMI_CH1_MUX CH0
+       sudo alsactl store
+     Reboot and log in. Confirm that the sinks and sources are the same
+     as in step 2, that
+       sudo amixer -c0 cget name=DPTX_OUT_MUX
+     shows Connect, that
+       sudo amixer -c0 cget name=HDMI_CH1_MUX
+     shows CH1, and that
+       journalctl --user -b -u wireplumber
+     has no "Error opening PCM device" line.
  
-  4. Select "DP output" in Settings > Sound and run the speaker test.
-     Confirm that Front Left and Front Right are heard from the monitor.
+  4. Select "DP output" in Settings > Sound and run the speaker test.
+     Confirm that Front Left and Front Right are heard from the monitor.
  
-  5. Plug in headphones, select them and run the speaker test. Confirm
-     that left and right are heard on the matching side and not in the
-     center.
+  5. Plug in headphones, select them and run the speaker test. Confirm
+     that left and right are heard on the matching side and not in the
+     center.
  
-  6. Move the output and input volume sliders. Confirm that
-     "Headset Volume", "Lineout Volume" and "PGA1 Volume" follow them in
-     alsamixer, and that a recording from the analog microphone has a
-     usable level.
+  6. Move the output and input volume sliders. Confirm that
+     "Headset Volume", "Lineout Volume" and "PGA1 Volume" follow them in
+     alsamixer, and that a recording from the analog microphone has a
+     usable level.
  
-  7. Boot with the default overlays (no display-dpoc.dtbo). Confirm that
-     there is no DP output and that all other sinks and sources from
-     step 2 are present.
+  7. Boot with the default overlays (no display-dpoc.dtbo). Confirm that
+     there is no DP output and that all other sinks and sources from
+     step 2 are present.
  
-  8. Regression test on the Framework Laptop 13: install the update,
-     play and record audio with the built-in speakers and microphone,
-     and confirm that "journalctl -b" has no new UCM errors.
+  8. Regression test on the Framework Laptop 13: install the update,
+     play and record audio with the built-in speakers and microphone,
+     and confirm that "journalctl -b" has no new UCM errors.
  
-  * Tenacious (the development release) is a normal upload and is not
-    part of the SRU verification.
+  * Tenacious (the development release) is a normal upload and is not
+    part of the SRU verification.
  
  [ Where problems could occur ]
  
-  * Only files under ucm2/MediaTek/mt8391-evk/ change. They are loaded
-    only for the mt8391-evk sound card, so other hardware is not
-    affected. To verify this, examine each debdiff attached to this bug:
-    the three patches touch only ucm2/MediaTek/mt8391-evk/HiFi.conf.
+  * Only files under ucm2/MediaTek/mt8391-evk/ change. They are loaded
+    only for the mt8391-evk sound card, so other hardware is not
+    affected. To verify this, examine each debdiff attached to this bug:
+    the three patches touch only ucm2/MediaTek/mt8391-evk/HiFi.conf.
  
-  * On the MT8391-EVK:
+  * On the MT8391-EVK:
  
-    - The verb EnableSequence runs every time the profile is activated.
-      If a kernel or device tree does not register one of the three mux
-      controls, activating the profile could fail and audio would be
-      lost. Test Plan step 7 covers the default overlays.
+    - The verb EnableSequence runs every time the profile is activated.
+      If a kernel or device tree does not register one of the three mux
+      controls, activating the profile could fail and audio would be
+      lost. Test Plan step 7 covers the default overlays.
  
-    - Speaker and Headphones priorities move to 400 and 500, above the
-      DP output (300). With a monitor attached the default output stays
-      the speaker and the user selects DP in the settings.
+    - Speaker and Headphones priorities move to 400 and 500, above the
+      DP output (300). With a monitor attached the default output stays
+      the speaker and the user selects DP in the settings.
  
-    - The volume sliders now drive the hardware gain, so the default
-      microphone level differs from before (louder).
+    - The volume sliders now drive the hardware gain, so the default
+      microphone level differs from before (louder).
  
  [ Other Info ]
  
-  * Upstream status:
+  * Upstream status:
  
-    - Patches 1 and 2 are backports of upstream commits merged on
-      master. The latest release, v1.2.16.1, does not contain them yet.
-      1. 8275e1b6577b "ucm2: MediaTek: mt8391-evk: Fix channels and add
-         volume controls"
-         https://github.com/alsa-project/alsa-ucm-conf/commit/8275e1b6577b
-      2. 8048d93df191 "ucm2: MediaTek: mt8391-evk: Add DisplayPort output
-         audio support"
-         https://github.com/alsa-project/alsa-ucm-conf/commit/8048d93df191
-    - Patch 3 is the fix for patch 2 and is NOT YET MERGED upstream:
-      3. "ucm2: MediaTek: mt8391-evk: Set the DP audio muxes in the verb"
-         (Fixes: 8048d93)
-         https://github.com/alsa-project/alsa-ucm-conf/pull/902
-      This bug will be updated when it merges, and the DEP-3 Origin of
-      patch 3 will be changed to the upstream commit.
+    - Patches 1 and 2 are backports of upstream commits merged on
+      master. The latest release, v1.2.16.1, does not contain them yet.
+      1. 8275e1b6577b "ucm2: MediaTek: mt8391-evk: Fix channels and add
+         volume controls"
+         https://github.com/alsa-project/alsa-ucm-conf/commit/8275e1b6577b
+      2. 8048d93df191 "ucm2: MediaTek: mt8391-evk: Add DisplayPort output
+         audio support"
+         https://github.com/alsa-project/alsa-ucm-conf/commit/8048d93df191
+    - Patch 3 is the fix for patch 2 and is NOT YET MERGED upstream:
+      3. "ucm2: MediaTek: mt8391-evk: Set the DP audio muxes in the verb"
+         (Fixes: 8048d93)
+         https://github.com/alsa-project/alsa-ucm-conf/pull/902
+      This bug will be updated when it merges, and the DEP-3 Origin of
+      patch 3 will be changed to the upstream commit.
  
-  * Sponsorship is requested. Debdiffs for Tenacious, Stonking, Resolute
-    and Noble will be attached to this bug. Each series gets the same
-    three patches, named after this bug number:
-    - 
lp<bug>-ucm2-MediaTek-mt8391-evk-Fix-channels-and-add-volume-controls.patch
-    - 
lp<bug>-ucm2-MediaTek-mt8391-evk-Add-DisplayPort-output-audio-support.patch
-    - lp<bug>-ucm2-MediaTek-mt8391-evk-Set-the-DP-audio-muxes-in-the-verb.patch
-    The resulting ucm2/MediaTek/mt8391-evk files are identical in all
-    four series.
+  * Sponsorship is requested. Debdiffs for Tenacious, Stonking, Resolute
+    and Noble will be attached to this bug. Each series gets the same
+    three patches, named after this bug number:
+    - 
lp2173715-ucm2-MediaTek-mt8391-evk-Fix-channels-and-add-volume-controls.patch
+    - 
lp2173715-ucm2-MediaTek-mt8391-evk-Add-DisplayPort-output-audio-support.patch
+    - 
lp2173715-ucm2-MediaTek-mt8391-evk-Set-the-DP-audio-muxes-in-the-verb.patch
+    The resulting ucm2/MediaTek/mt8391-evk files are identical in all
+    four series.
  
-  * Debian: the first two patches are upstream commits and reach Debian
-    with the next upstream release. Patch 3 is forwarded
-    upstream as PR #902. No separate Debian bug is planned.
+  * Debian: the first two patches are upstream commits and reach Debian
+    with the next upstream release. Patch 3 is forwarded
+    upstream as PR #902. No separate Debian bug is planned.
  
-  * Tested on a Genio 720 EVK running 24.04: stereo output and volume
-    controls, and DisplayPort audio including a reboot with a stale
-    saved state, with the same changes except the Speaker and
-    Headphones priority values.
+  * Tested on a Genio 720 EVK running 24.04: stereo output and volume
+    controls, and DisplayPort audio including a reboot with a stale
+    saved state, with the same changes except the Speaker and
+    Headphones priority values.
  
-  * Target releases:
-    - Tenacious: 1.2.16.1-1ubuntu1 -> 1.2.16.1-1ubuntu2
-    - Stonking:  1.2.16.1-1ubuntu1 -> 1.2.16.1-1ubuntu1.1
-    - Resolute:  1.2.15.3-1ubuntu1.7 -> 1.2.15.3-1ubuntu1.8
-    - Noble:     1.2.10-1ubuntu5.16 -> 1.2.10-1ubuntu5.17
-      (5.16 is in noble-proposed, LP: #2068911)
+  * Target releases:
+    - Tenacious: 1.2.16.1-1ubuntu1 -> 1.2.16.1-1ubuntu2
+    - Stonking:  1.2.16.1-1ubuntu1 -> 1.2.16.1-1ubuntu1.1
+    - Resolute:  1.2.15.3-1ubuntu1.7 -> 1.2.15.3-1ubuntu1.8
+    - Noble:     1.2.10-1ubuntu5.16 -> 1.2.10-1ubuntu5.17
+      (5.16 is in noble-proposed, LP: #2068911)
  
-  * The Tenacious and Stonking debdiffs also run update-maintainer,
-    because the current upload still has the Debian maintainer in
-    debian/control.
+  * The Tenacious and Stonking debdiffs also run update-maintainer,
+    because the current upload still has the Debian maintainer in
+    debian/control.

-- 
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
https://bugs.launchpad.net/bugs/2173715

Title:
  [SRU] MediaTek MT8391-EVK: fix stereo output, add volume controls and
  DisplayPort audio

To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/alsa-ucm-conf/+bug/2173715/+subscriptions


-- 
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs

Reply via email to