In response to Stefan Bader's post :
I tried your linux-image-2.6.24-19-generic_2.6.24-19.35smb2_i386.deb
When i boot up it worked but i have to say that i added "options forcedeth
msi=0 msix=0" to my /etc/modprobe.d/options
Do you want me to test without this line ?
Here is my dmesg | grep forcedeth :
[ 54.326399] forcedeth: Reverse Engineered nForce ethernet driver. Version
0.61.
[ 54.326705] forcedeth 0000:00:11.0: msi_enabled=0 msix_enabled=0
[ 54.844639] forcedeth 0000:00:11.0: ifname eth0, PHY OUI 0x5043 @ 19, addr
00:1a:92:2b:76:4d
[ 54.844642] forcedeth 0000:00:11.0: highdma csum vlan pwrctl mgmt timirq
gbit lnktim desc-v3
[ 54.844959] forcedeth 0000:00:12.0: msi_enabled=0 msix_enabled=0
Here is my lspci -vvnn :
00:11.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a2)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at efffa000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at ec00 [size=8]
Region 2: Memory at efff9000 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at efff8000 (32-bit, non-prefetchable) [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [70] MSI-X: Enable- Mask- TabSize=8
Vector table: BAR=2 offset=00000000
PBA: BAR=3 offset=00000000
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/3
Enable-
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping
00:12.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a2)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:cb84]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at efff7000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at eb00 [size=8]
Region 2: Memory at efff6000 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at efff5000 (32-bit, non-prefetchable) [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [70] MSI-X: Enable- Mask- TabSize=8
Vector table: BAR=2 offset=00000000
PBA: BAR=3 offset=00000000
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/3
Enable-
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping
Hope it helped.
If you want more tests, just tell me, i would be glad to help you solve this
problem.
--
Ethernet (nVidia MCP55) not working [ gutsy, hardy]
https://bugs.launchpad.net/bugs/136836
You received this bug notification because you are a member of Ubuntu
Bugs, which is subscribed to Ubuntu.
--
ubuntu-bugs mailing list
[email protected]
https://lists.ubuntu.com/mailman/listinfo/ubuntu-bugs
