Huh, ubuntu-bug didn't attach the output of "sudo ddcprobe", so here we
go:
vbe: VESA 3.0 detected.
oem: NVIDIA
vendor: NVIDIA Corporation
product: nv43 Board - p229h3 Chip Rev
memory: 131072kb
mode: 640x400x256
mode: 640x480x256
mode: 800x600x16
mode: 800x600x256
mode: 1024x768x16
mode: 1024x768x256
mode: 1280x1024x16
mode: 1280x1024x256
mode: 320x200x64k
mode: 320x200x16m
mode: 640x480x64k
mode: 640x480x16m
mode: 800x600x64k
mode: 800x600x16m
mode: 1024x768x64k
mode: 1024x768x16m
mode: 1280x1024x64k
mode: 1280x1024x16m
edid:
edid: 1 3
id: 8991
eisa: HSD8991
serial: 01010101
manufacture: 6 2007
input: composite sync, sync on green, analog signal.
screensize: 41 26
gamma: 2.200000
dpms: RGB, active off, no suspend, no standby
timing: 720x...@70 Hz (VGA 640x400, IBM)
timing: 720x...@88 Hz (XGA2)
timing: 640x...@60 Hz (VGA)
timing: 640x...@67 Hz (Mac II, Apple)
timing: 640x...@72 Hz (VESA)
timing: 640x...@75 Hz (VESA)
timing: 800x...@60 Hz (VESA)
timing: 800x...@72 Hz (VESA)
timing: 800x...@75 Hz (VESA)
timing: 832x...@75 Hz (Mac II)
timing: 1024x...@87 Hz Interlaced (8514A)
timing: 1024x...@70 Hz (VESA)
timing: 1024x...@75 Hz (VESA)
timing: 1280x1...@75 (VESA)
ctiming: 640x...@66
ctiming: 1024x...@66
ctiming: 1152x...@75
ctiming: 1280x...@60
ctiming: 1280x1...@60
ctiming: 1440x1...@60
ctiming: 1440x1...@75
dtiming: 1440x...@69
monitorrange: 30-80, 49-75
monitorname: Hanns.G HW19
monitorserial: 706HP3CY0486
Also, here's the output of "sudo get-edid|parse-edid":
parse-edid: parse-edid version 2.0.0
get-edid: get-edid version 2.0.0
Performing real mode VBE call
Interrupt 0x10 ax=0x4f00 bx=0x0 cx=0x0
Function supported
Call successful
VBE version 300
VBE string at 0x2110 "NVIDIA"
VBE/DDC service about to be called
Report DDC capabilities
Performing real mode VBE call
Interrupt 0x10 ax=0x4f15 bx=0x0 cx=0x0
Function supported
Call successful
Monitor and video card combination does not support DDC1 transfers
Monitor and video card combination supports DDC2 transfers
0 seconds per 128 byte EDID block transfer
Screen is not blanked during DDC transfer
Reading next EDID block
VBE/DDC service about to be called
Read EDID
Performing real mode VBE call
Interrupt 0x10 ax=0x4f15 bx=0x1 cx=0x0
Function supported
Call successful
parse-edid: EDID checksum passed.
# EDID version 1 revision 3
Section "Monitor"
# Block type: 2:0 3:fd
# Block type: 2:0 3:fc
Identifier "Hanns.G HW194"
VendorName "HSD"
ModelName "Hanns.G HW194"
# Block type: 2:0 3:fd
HorizSync 30-80
VertRefresh 49-75
# Max dot clock (video bandwidth) 140 MHz
# Block type: 2:0 3:fc
# Block type: 2:0 3:ff
# DPMS capabilities: Active off:yes Suspend:no Standby:no
Mode "1440x900" # vfreq 59.887Hz, hfreq 55.935kHz
DotClock 106.500000
HTimings 1440 1520 1672 1904
VTimings 900 903 909 934
Flags "+HSync" "-VSync"
EndMode
# Block type: 2:0 3:fd
# Block type: 2:0 3:fc
# Block type: 2:0 3:ff
EndSection
--
wrong resolutions autodetected with Hanns.G HW194DJ monitor + NVidia GeForce
6600
https://bugs.launchpad.net/bugs/474816
You received this bug notification because you are a member of Ubuntu-X,
which is subscribed to xorg in ubuntu.
_______________________________________________
Mailing list: https://launchpad.net/~ubuntu-x-swat
Post to : [email protected]
Unsubscribe : https://launchpad.net/~ubuntu-x-swat
More help : https://help.launchpad.net/ListHelp
