On 05/27/2012 10:56 AM, Chaitanya kumar CH wrote:
Alassane,
The only suggestion I can make without going too deep is to run "make
clean" before running "make" again.
On Fri, May 25, 2012 at 9:17 PM, Alassane Toure <[email protected]
<mailto:[email protected]>> wrote:
On 05/25/2012 02:56 AM, Chaitanya kumar CH wrote:
Alassane,
libtool may have some problem.
Replace "./configure" with "./configure --without-libtool"
Make sure you have the format drivers you need listed in the
configure script's output.
On Fri, May 25, 2012 at 8:48 AM, Alassane Toure
<[email protected] <mailto:[email protected]>> wrote:
Roland,
I followed the steps as suggested by the link and a couple of
errors came up after issuing "make"
....
....
-rpath /usr/local/lib \
-no-undefined \
-version-info 17:1:16
libtool: link: unable to infer tagged configuration
libtool: link: specify a tag with `--tag'
make[1]: *** [libgdal.la <http://libgdal.la>] Error 1
make[1]: Leaving directory `/home/alassane/Downloads/gdal-1.9.1'
make: *** [check-lib] Error 2
Any suggestion to fix this?
Again thanks,
Alassane
On 05/24/2012 02:21 PM, Roland van Laar wrote:
On 05/24/2012 09:16 PM, Alassane Toure wrote:
Group,
I need help to install GDAL 1.9.1 on Ubuntu 12.04. I
first downloaded gdal-1.9.1.tar.gz, uncompressed it
and executed ./configure. Where do I go from here?
Have you read: http://trac.osgeo.org/gdal/wiki/BuildingOnUnix
It contains the information needed for building GDAL.
Roland
Thanks for your help
_______________________________________________
UbuntuGIS mailing list
[email protected] <mailto:[email protected]>
http://lists.osgeo.org/mailman/listinfo/ubuntu
http://trac.osgeo.org/ubuntugis/wiki
_______________________________________________
UbuntuGIS mailing list
[email protected] <mailto:[email protected]>
http://lists.osgeo.org/mailman/listinfo/ubuntu
http://trac.osgeo.org/ubuntugis/wiki
--
Best regards,
Chaitanya kumar CH.
+91-9494447584 <tel:%2B91-9494447584>
17.2416N 80.1426E
Thanks Chaitanya,
I used your suggested command and again, a couple of errors are
reported after "make" was issued (see below). FYI, I had
installed gdal-1.8.0 on a 32-bit Oneric OS without problem. I
recently moved to 64-bit Precise OS and installation of gdal-1.9.1
appear non-trivial. Any suggestion to fix this? Again, Thanks,
...
...
/usr/bin/ld:
/home/alassane/Downloads/gdal-1.9.1/frmts/o/aigccitt.o: relocation
R_X86_64_32S against `.rodata' can not be used when making a
shared object; recompile with -fPIC
/home/alassane/Downloads/gdal-1.9.1/frmts/o/aigccitt.o: could not
read symbols: Bad value
collect2: ld returned 1 exit status
make[1]: *** [/home/alassane/Downloads/gdal-1.9.1/libgdal.so] Error 1
make[1]: Leaving directory `/home/alassane/Downloads/gdal-1.9.1'
make: *** [check-lib] Error 2
--
Best regards,
Chaitanya kumar CH.
+91-9494447584
17.2416N 80.1426E
Chaitanya,
I followed your instructions ["make clean" and "make"] and the process
went without any error reported. However, when I check the gdal version
"gdal-config --version" only version 1.7.0 is installed and all
libraries in "/usr/lib refer to version 1.7.0. Thus, compilation with
1.7.0 works but not with 1.9.1. Any other thoughts?
Thank you very much!
Alassane
_______________________________________________
UbuntuGIS mailing list
[email protected]
http://lists.osgeo.org/mailman/listinfo/ubuntu
http://trac.osgeo.org/ubuntugis/wiki
