hello David McCullough ok. i will try what you have say.. thankyou for your reply...
thank you for your reply... i am also trying to use Montavista... ok will tell once i have done that thank you... regards raj --- David McCullough <[EMAIL PROTECTED]> wrote: > > Jivin RAJA GOPAL lays it down ... > > hello David McCullough > > > > Tahank you for your replay... > > > > i tried by removing that insmod ixp425_eth.o from > that > > file. after that i tried to run the codelets it > says > > the following: > > > > insmod ixp400_codelets_ethAcc.o operationType=5 > > Using > > > /lib/modules/2.4.24-uc0/kernel/drivers/ixp400/ixp400_codelets_ethAcc.o > > Warning: loading ixp400_codelets_ethAcc will taint > the > > kernel: no license > > See http://www.tux.Load Codelet: EthAcc. > > org/lkml/#export-tainted for information about > tainted > > modules > > Initialising Queue Manager... > > ixQMgrInit: IxQMgr already initialised > > Error initialising queue manager! > > ixEthAccCodeletInit() fails ! Exit > > > > what i have to do in order to run the codelets > > example... > > remove all the module loads from the rc file, the > ixp400 or whatever > it's called is probably also causing problems. > > Also note that the codelets are rarely used (since > most people just use > the eth/crypto/dsp modules as supplied). So you may > need to mod them a > little. > > Cheers > Davidm > > > > > > thanks in advance > > > > raj > > > > > > --- David McCullough > > <[EMAIL PROTECTED]> wrote: > > > > > > > > Jivin RAJA GOPAL lays it down ... > > > > hi all > > > > > > > > i am using Intel IXP425. and i have don the > > > following > > > > things: > > > > > > > > snapgear snapgear-3.1.1.tar.gz, along with > > > > arm-linux-tools-20030927.tar.gz and intels > > > > ixp400AccessLibrary-1_4.zip i have made the > zImage > > > and > > > > the ramdisk... > > > > > > > > if i try's to run the codelets example IXP425 > > > Ethernet > > > > Access Codelet its says the Queue alredy > intilized > > > and > > > > then it stopes. > > > > > > > > how to stop the configure the operating system > > > with > > > > out NPE based ethernet device drivers > > > > > > You have probably loaded the ethernet driver > modules > > > in /etc/rc > > > > > > Remove them then you should be able to get the > > > codelets going, > > > > > > Cheers, > > > Davidm > > > > > > -- > > > David McCullough, > > > [EMAIL PROTECTED], Ph:+61 > > > 734352815 > > > Secure Computing - SnapGear > http://www.uCdot.org > > > http://www.cyberguard.com > > > _______________________________________________ > > > uClinux-dev mailing list > > > [email protected] > > > > > > http://mailman.uclinux.org/mailman/listinfo/uclinux-dev > > > This message was resent by > [email protected] > > > To unsubscribe see: > > > > > > http://mailman.uclinux.org/mailman/options/uclinux-dev > > > > > > > > > > > > > > ____________________________________________________________________________________ > > TV dinner still cooling? > > Check out "Tonight's Picks" on Yahoo! TV. > > http://tv.yahoo.com/ > > _______________________________________________ > > uClinux-dev mailing list > > [email protected] > > > http://mailman.uclinux.org/mailman/listinfo/uclinux-dev > > This message was resent by [email protected] > > To unsubscribe see: > > > http://mailman.uclinux.org/mailman/options/uclinux-dev > > -- > David McCullough, > [EMAIL PROTECTED], Ph:+61 > 734352815 > Secure Computing - SnapGear http://www.uCdot.org > http://www.cyberguard.com > _______________________________________________ > uClinux-dev mailing list > [email protected] > http://mailman.uclinux.org/mailman/listinfo/uclinux-dev > This message was resent by [email protected] > To unsubscribe see: > http://mailman.uclinux.org/mailman/options/uclinux-dev > ____________________________________________________________________________________ No need to miss a message. Get email on-the-go with Yahoo! Mail for Mobile. Get started. http://mobile.yahoo.com/mail _______________________________________________ uClinux-dev mailing list [email protected] http://mailman.uclinux.org/mailman/listinfo/uclinux-dev This message was resent by [email protected] To unsubscribe see: http://mailman.uclinux.org/mailman/options/uclinux-dev
