Hi Will,
will wrote:
I have encoutered some problems with my coldfire m5272 board running
uclinux of version 2.6.17-uc1.
My board has 64M sdram and I configured the "CONFIG_RAMSIZE" with the
value of 0x04000000 instead of the default value 8M. When I increase the
ramfs image from 128k default to 2048k, system will hang up while
expanding the ramfs image. Then, I configured the ram size back to the
default value 8M, the system works well and never hang up again.
If you use the 128k ramfs image, but with the memory size set to
64MB does the system boot and work?
Are you sure that all 64MB of SDRAM is actually working properly?
Regards
Greg
I am very confused about this problem and does anyone can give me advice
to solve the problem?
Thanks in advance!
PS: following is my kernel config and console output
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.17-uc1
# Wed May 9 09:56:32 2007
#
CONFIG_M68K=y
# CONFIG_MMU is not set
# CONFIG_FPU is not set
CONFIG_RWSEM_GENERIC_SPINLOCK=y
# CONFIG_RWSEM_XCHGADD_ALGORITHM is not set
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_TIME_LOW_RES=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
CONFIG_BROKEN_ON_SMP=y
CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
CONFIG_LOCALVERSION=""
CONFIG_LOCALVERSION_AUTO=y
# CONFIG_SYSVIPC is not set
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_SYSCTL is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_UID16=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_EMBEDDED=y
# CONFIG_KALLSYMS is not set
# CONFIG_HOTPLUG is not set
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
# CONFIG_FUTEX is not set
# CONFIG_EPOLL is not set
CONFIG_SLAB=y
CONFIG_TINY_SHMEM=y
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set
CONFIG_OBSOLETE_INTERMODULE=y
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
# CONFIG_KMOD is not set
#
# Block layer
#
# CONFIG_BLK_DEV_IO_TRACE is not set
#
# IO Schedulers
#
CONFIG_IOSCHED_NOOP=y
# CONFIG_IOSCHED_AS is not set
# CONFIG_IOSCHED_DEADLINE is not set
CONFIG_IOSCHED_CFQ=y
# CONFIG_DEFAULT_AS is not set
# CONFIG_DEFAULT_DEADLINE is not set
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
#
# Processor type and features
#
# CONFIG_M68328 is not set
# CONFIG_M68EZ328 is not set
# CONFIG_M68VZ328 is not set
# CONFIG_M68360 is not set
# CONFIG_M5206 is not set
# CONFIG_M5206e is not set
# CONFIG_M520x is not set
# CONFIG_M523x is not set
# CONFIG_M5249 is not set
# CONFIG_M5271 is not set
CONFIG_M5272=y
# CONFIG_M5275 is not set
# CONFIG_M528x is not set
# CONFIG_M5307 is not set
# CONFIG_M532x is not set
# CONFIG_M5407 is not set
CONFIG_COLDFIRE=y
CONFIG_CLOCK_SET=y
CONFIG_CLOCK_FREQ=66666666
CONFIG_CLOCK_DIV=1
#
# Platform
#
CONFIG_M5272C3=y
# CONFIG_COBRA5272 is not set
# CONFIG_CANCam is not set
# CONFIG_SCALES is not set
# CONFIG_NETtel is not set
# CONFIG_CPU16B is not set
# CONFIG_MOD5272 is not set
CONFIG_FREESCALE=y
CONFIG_LARGE_ALLOCS=y
CONFIG_4KSTACKS=y
#
# RAM configuration
#
CONFIG_RAMBASE=0x00000000
CONFIG_RAMSIZE=0x04000000
CONFIG_VECTORBASE=0x00000000
CONFIG_KERNELBASE=0x00020000
CONFIG_RAMAUTOBIT=y
# CONFIG_RAM8BIT is not set
# CONFIG_RAM16BIT is not set
# CONFIG_RAM32BIT is not set
#
# ROM configuration
#
# CONFIG_ROM is not set
CONFIG_RAMKERNEL=y
# CONFIG_ROMKERNEL is not set
CONFIG_CF_SHARED_INTS=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
# CONFIG_SPARSEMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
CONFIG_SPLIT_PTLOCK_CPUS=4
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
# CONFIG_PCI is not set
#
# PCCARD (PCMCIA/CardBus) support
#
# CONFIG_PCCARD is not set
#
# PCI Hotplug Support
#
#
# Executable file formats
#
CONFIG_BINFMT_FLAT=y
# CONFIG_BINFMT_ZFLAT is not set
# CONFIG_BINFMT_SHARED_FLAT is not set
# CONFIG_BINFMT_AOUT is not set
# CONFIG_BINFMT_MISC is not set
#
# Power management options
#
# CONFIG_PM is not set
#
# Networking
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_GENETLINK=y
# CONFIG_NETDEBUG is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
# CONFIG_IP_PNP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_XFRM_TUNNEL is not set
# CONFIG_INET_TUNNEL is not set
# CONFIG_IPSEC_NAT_TRAVERSAL is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
# CONFIG_IPV6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETFILTER is not set
#
# DCCP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_DCCP is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
# CONFIG_IP_SCTP is not set
#
# TIPC Configuration (EXPERIMENTAL)
#
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_KLIPS is not set
# CONFIG_IEEE80211 is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
#
# Connector - unified userspace <-> kernelspace linker
#
# CONFIG_CONNECTOR is not set
#
# Memory Technology Devices (MTD)
#
CONFIG_MTD=y
# CONFIG_MTD_DEBUG is not set
CONFIG_MTD_CONCAT=y
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
#
# User Modules And Translation Layers
#
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
# CONFIG_FTL is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
#
# RAM/ROM/Flash chip drivers
#
CONFIG_MTD_CFI=y
# CONFIG_MTD_JEDECPROBE is not set
CONFIG_MTD_GEN_PROBE=y
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
# CONFIG_MTD_CFI_INTELEXT is not set
CONFIG_MTD_CFI_AMDSTD=y
# CONFIG_MTD_CFI_STAA is not set
CONFIG_MTD_CFI_UTIL=y
CONFIG_MTD_RAM=y
# CONFIG_MTD_EPCS is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
# CONFIG_MTD_OBSOLETE_CHIPS is not set
#
# Mapping drivers for chip access
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
# CONFIG_MTD_PHYSMAP is not set
CONFIG_MTD_UCLINUX=y
CONFIG_MTD_UCLINUX_EBSS=y
# CONFIG_MTD_SNAPGEARuC is not set
# CONFIG_MTD_M520x is not set
CONFIG_MTD_M5272C3=y
# CONFIG_MTD_PLATRAM is not set
# CONFIG_MTD_AVNET5282 is not set
#
# Self-contained MTD device drivers
#
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_MTD_BLOCK2MTD is not set
#
# Disk-On-Chip Device Drivers
#
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
#
# NAND Flash Device Drivers
#
# CONFIG_MTD_NAND is not set
#
# OneNAND Flash Device Drivers
#
# CONFIG_MTD_ONENAND is not set
#
# Parallel port support
#
# CONFIG_PARPORT is not set
#
# Plug and Play support
#
#
# Block devices
#
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
# CONFIG_BLK_DEV_NBD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=4096
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# ATA/ATAPI/MFM/RLL support
#
# CONFIG_IDE is not set
#
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
#
#
# I2O device support
#
#
# Network device support
#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
#
# PHY device support
#
# CONFIG_PHYLIB is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_MII is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_OPEN_ETH is not set
# CONFIG_MTIP1000_ETH is not set
# CONFIG_NE2000 is not set
# CONFIG_NET_PCI is not set
CONFIG_FEC=y
# CONFIG_FEC2 is not set
#
# Ethernet (1000 Mbit)
#
#
# Ethernet (10000 Mbit)
#
#
# Token Ring devices
#
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
#
# CONFIG_ISDN is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
#
# Input device support
#
# CONFIG_INPUT is not set
#
# Hardware I/O ports
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
#
# Character devices
#
# CONFIG_VT is not set
# CONFIG_SERIAL_NONSTANDARD is not set
# CONFIG_LEDMAN is not set
# CONFIG_SNAPDOG is not set
# CONFIG_FAST_TIMER is not set
# CONFIG_RESETSWITCH is not set
#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
#
# Non-8250 serial port support
#
CONFIG_SERIAL_COLDFIRE=y
# CONFIG_SERIAL_MCF is not set
# CONFIG_UNIX98_PTYS is not set
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
#
# IPMI
#
# CONFIG_IPMI_HANDLER is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_MCFWATCHDOG is not set
# CONFIG_GEN_RTC is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_RAW_DRIVER is not set
#
# TPM devices
#
# CONFIG_TCG_TPM is not set
CONFIG_MCF_QSPI=y
# CONFIG_M41T11M6 is not set
# CONFIG_TELCLOCK is not set
#
# I2C support
#
# CONFIG_I2C is not set
#
# SPI support
#
# CONFIG_SPI is not set
# CONFIG_SPI_MASTER is not set
#
# Dallas's 1-wire bus
#
# CONFIG_W1 is not set
#
# Hardware Monitoring support
#
CONFIG_HWMON=y
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_F71805F is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Misc devices
#
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
CONFIG_VIDEO_V4L2=y
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
#
# Graphics support
#
CONFIG_FB=y
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_FIRMWARE_EDID is not set
# CONFIG_FB_MODE_HELPERS is not set
# CONFIG_FB_TILEBLITTING is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
#
# Logo configuration
#
# CONFIG_LOGO is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
#
# CONFIG_SOUND is not set
#
# USB support
#
# CONFIG_USB_ARCH_HAS_HCD is not set
# CONFIG_USB_ARCH_HAS_OHCI is not set
# CONFIG_USB_ARCH_HAS_EHCI is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
# MMC/SD Card support
#
# CONFIG_MMC is not set
#
# LED devices
#
# CONFIG_NEW_LEDS is not set
#
# LED drivers
#
#
# LED Triggers
#
#
# InfiniBand support
#
#
# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
#
#
# Real Time Clock
#
# CONFIG_RTC_CLASS is not set
#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
# CONFIG_EXT3_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
CONFIG_ROMFS_FS=y
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
# CONFIG_FUSE_FS is not set
CONFIG_DIRECTIO=y
#
# CD-ROM/DVD Filesystems
#
# CONFIG_ISO9660_FS is not set
# CONFIG_UDF_FS is not set
#
# DOS/FAT/NT Filesystems
#
# CONFIG_MSDOS_FS is not set
# CONFIG_VFAT_FS is not set
# CONFIG_NTFS_FS is not set
#
# Pseudo filesystems
#
CONFIG_PROC_FS=y
CONFIG_SYSFS=y
# CONFIG_TMPFS is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# Miscellaneous filesystems
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_FS_DEBUG=0
# CONFIG_JFFS2_FS_WRITEBUFFER is not set
# CONFIG_JFFS2_SUMMARY is not set
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
# CONFIG_CRAMFS is not set
# CONFIG_SQUASHFS is not set
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
#
# Network File Systems
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_9P_FS is not set
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
#
# Native Language Support
#
# CONFIG_NLS is not set
#
# Debug
#
# CONFIG_COREDUMP_PRINTK is not set
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_LOG_BUF_SHIFT=14
# CONFIG_DEBUG_BUGVERBOSE is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_UNWIND_INFO is not set
# CONFIG_FULLDEBUG is not set
# CONFIG_HIGHPROFILE is not set
CONFIG_BOOTPARAM=y
CONFIG_BOOTPARAM_STRING="rootfstype=romfs"
# CONFIG_DUMPTOFLASH is not set
# CONFIG_NO_KERNEL_MSG is not set
# CONFIG_BDM_DISABLE is not set
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
CONFIG_CRYPTO=y
# CONFIG_CRYPTO_HMAC is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_MD4 is not set
# CONFIG_CRYPTO_MD5 is not set
# CONFIG_CRYPTO_SHA1 is not set
# CONFIG_CRYPTO_SHA256 is not set
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
# CONFIG_CRYPTO_DES is not set
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
# CONFIG_CRYPTO_SERPENT is not set
# CONFIG_CRYPTO_AES is not set
# CONFIG_CRYPTO_CAST5 is not set
# CONFIG_CRYPTO_CAST6 is not set
# CONFIG_CRYPTO_TEA is not set
# CONFIG_CRYPTO_ARC4 is not set
# CONFIG_CRYPTO_KHAZAD is not set
# CONFIG_CRYPTO_ANUBIS is not set
# CONFIG_CRYPTO_DEFLATE is not set
# CONFIG_CRYPTO_MICHAEL_MIC is not set
# CONFIG_CRYPTO_CRC32C is not set
# CONFIG_CRYPTO_TEST is not set
#
# Hardware crypto devices
#
#
# Library routines
#
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
Linux version 2.6.17-uc1 ([EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>) (gcc version 4.1.1) #145 Wed May 9
09:59:03 CST 2007
uClinux/COLDFIRE(m5272)
COLDFIRE port done by Greg Ungerer, [EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>
Flat model support (C) 1998,1999 Kenneth Albanowski, D. Jeff Dionne
Built 1 zonelists
Kernel command line: rootfstype=romfs
PID hash table entries: 512 (order: 9, 2048 bytes)
timer (at 0x00022d62) called request_irq without a dev_id!
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory available: 62396k/65536k RAM, (1227k kernel code, 176k data)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
JFFS2 version 2.2. (C ) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler cfq registered (default)
QSPI device driver installed OK
ColdFire QSPI (at 0x000c681c) called request_irq without a dev_id!
MCF5272 QSPI driver ok
ColdFire internal UART serial driver version 1.00
ColdFire UART (at 0x000c7a8e) called request_irq without a dev_id!
ttyS0 at 0x10000100 (irq = 73) is a builtin ColdFire UART
ColdFire UART (at 0x000c7a8e) called request_irq without a dev_id!
ttyS1 at 0x10000140 (irq = 74) is a builtin ColdFire UART
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
FEC ENET Version 0.2
fec: PHY @ 0x0, ID 0x001378e2 -- LXT971
eth0: ethernet 00:cf:52:72:c3:0a
uclinux[mtd]: RAM probe address=0x17f2d4 size=0xf2000
Creating 1 MTD partitions on "RAM":
0x00000000-0x000f2000 : "ROMfs"
uclinux[mtd]: set ROMfs to be root filesystem
m5272c3 flash probe(0xff000000,800000,2): 800000 at ff000000
MCF5272C3 flash device: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
MCF5272C3 flash device: CFI does not contain boot bank location.
Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 3 MTD partitions on "MCF5272C3 flash device":
0x00000000-0x00030000 : "loader (192K)"
0x00030000-0x00040000 : "param (64K)"
0x000c0000-0x00800000 : "kernel (7424K)"
m5272c3 flash probe(0xff800000,800000,2): 800000 at ff800000
MCF5272C3 flash device 2: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
MCF5272C3 flash device 2: CFI does not contain boot bank location.
Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 2 MTD partitions on "MCF5272C3 flash device 2":
0x00000000-0x00010000 : "reserved (64K)"
0x000100 00-0x00800000 : "JFFS2 (8132K)"
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (romfs filesystem) readonly.
Freeing unused kernel memory: 48k freed (0x15f000 - 0x16a000)
init started: BusyBox v1.00 (2007.04.27-04:30+0000) multi-call binary
init started: BusyBox v1.00 (2007.04.27-04:30+0000) multi-call binary
Starting pid 14, console : '/etc/rc'
Mount flash filesystem
BR,
Will Huang
ÏÖÔÚ¹ºÂò21CNÆóÒµÓÊÏä,¼´¿ÉÓÃ100Ôª»»5000Ôª!
<http://mail.21cn.com/huodong/0704/index.html>
ÖíÄêÐдóÔË£¬²ÂͼӮ»°·Ñ£¡
<http://v.21cn.com/tvb/tvb.html?rcc_id=5c450d3206cbbc3f1f7e28e36d19aee5>
------------------------------------------------------------------------
_______________________________________________
uClinux-dev mailing list
uClinux-dev@uclinux.org
http://mailman.uclinux.org/mailman/listinfo/uclinux-dev
This message was resent by uclinux-dev@uclinux.org
To unsubscribe see:
http://mailman.uclinux.org/mailman/options/uclinux-dev
--
------------------------------------------------------------------------
Greg Ungerer -- Chief Software Dude EMAIL: [EMAIL PROTECTED]
SnapGear -- a Secure Computing Company PHONE: +61 7 3435 2888
825 Stanley St, FAX: +61 7 3891 3630
Woolloongabba, QLD, 4102, Australia WEB: http://www.SnapGear.com
_______________________________________________
uClinux-dev mailing list
uClinux-dev@uclinux.org
http://mailman.uclinux.org/mailman/listinfo/uclinux-dev
This message was resent by uclinux-dev@uclinux.org
To unsubscribe see:
http://mailman.uclinux.org/mailman/options/uclinux-dev
