Dear all,

thanks for all the support,

i could get back working on this, seems the issue was in my code, i was someway breaking the memory with a bad pointer.

I am now only confused now about the fact that uClinux die (blocks completely) silently in this case, if this is normal.

Many thanks
Angelo

On 28/01/2014 20:38, Larry Baker wrote:
Angelo,

Try leaving off the -Wl-M... option when you use the uClinux toolchain. That assumes you do not need a map. If you do, you might have to manually run ld to generate that.

The last Code Sourcery ColdFire gcc I worked with can be downloaded from https://sourcery.mentor.com/public/gnu_toolchain/m68k-uclinux/freescale-coldfire-2011.09-23-m68k-uclinux-i686-pc-linux-gnu.tar.bz2. I could not see ColdFire listed any longer on the Lite Edition web page, http://www.mentor.com/embedded-software/sourcery-tools/sourcery-codebench/editions/lite-edition, so that may or may not be the last release.

You may have to use gdb to track down the location of your problem. Here's an article about setting up a remote gdb debugger session: http://luv.asn.au/overheads/embedded/Debugging_uClinux_on_Coldfire.pdf.

Larry Baker
US Geological Survey
650-329-5608
ba...@usgs.gov <mailto:ba...@usgs.gov>



On 23 Jan 2014, at 2:31 PM, Angelo Dureghello wrote:

Dear Larry,

many thanks for the very useful info, unfortunately i have still not solved.

Original stack size in the header was 4096, i set it up growing until 65535, same result, program block and paralize the uclinux system without any wanring.

I have some doubt,
1) for example about the fact that i see that ti have compiled uclinux with CodeSourcery toolchain (i did it some time ago don't remember exactly the reason now), can this be an issue ? Anyway, actually i am compiling my c++ program with this same toolchain (gcc 4.6.1). 2) could i have some uclinux configuration issues ? In particular i have doubt on general setup and processor

General Setup:
 [*] Prompt for development and/or incomplete code/drivers
 ()  Cross-compiler tool prefix
 ()  Local version - append to kernel release
 [*] Automatically append version information to the version string
 [*] System V IPC
 [ ] POSIX Message Queues
 [ ] BSD Process Accounting
 [ ] Export task/process statistics through netlink (EXPERIMENTAL)
 [ ] Auditing support
RCU Subsystem  --->
 [ ] Kernel .config support
 (14) Kernel log buffer size (16 => 64KB, 17 => 128KB)
 [ ] enable deprecated sysfs features to support old userspace tools
 [ ] Kernel->user space relay support (formerly relayfs)
 [ ] Namespaces support
 [ ] Initial RAM filesystem and RAM disk (initramfs/initrd) support
 [ ] Optimize for size
 [*] Configure standard kernel features (for small systems)  --->
Kernel Performance Events And Counters --->
 [ ] Enable VM event counters for /proc/vmstat
 [*] Enable SLUB debugging support
 [*] Disable heap randomization
Choose SLAB allocator (SLUB (Unqueued Allocator))  --->
 [ ] Allow mmapped anonymous memory to be uninitialized
 [ ] Profiling support
GCOV-based kernel profiling  --->

    CPU (MCF5307)  --->
 [*] Enable setting the CPU clock frequency
 (90000000) Set the core clock frequency
 (2)   Set the core/bus clock divide ratio
 [ ] Old mask 5307 (1H55J) silicon
 *** Platform ***
 [*] Sysam AMCORE board support
 [ ] Arnewsh 5307 board support
 [ ] Motorola M5307C3 board support
 [ ] SnapGear SecureEdge/MP3 platform support
 [ ] Feith CLEOPATRA board support
 [ ] SecureEdge/NETtel board support
 [*] Support for U-Boot command line parameters
 [*] Use 4Kb for kernel stacks instead of 8Kb
 *** RAM configuration ***
 (0) Address of the base of RAM
 (0x1000000) Size of RAM (in bytes), or 0 for automatic
 (0x0) Address of the base of system vectors
 (0x20000) Address of the base of kernel code
 RAM bus width (AUTO)  --->
 *** ROM configuration ***
 [ ] Specify ROM linker regions
 Kernel executes from (RAM)  --->
 Preemption Model (No Forced Preemption (Server))  --->
 Memory model (Flat Memory)  --->
   (1) Turn on mmap() excess space trimming before booting

Do you see something strange here ?

I go on investingating,

Many thanks,
angelo



On 23/01/2014 19:49, Larry Baker wrote:
Angelo,

This sounds like your application stack size is too small and you are overflowing the stack. Remember, uClinux has no MMU to protect for that. Try increasing the stack size. Ted Ma told me once the application flthdr can manipulate the stack size in the executable's header:

Hi Larry,
  flthdr is the utility to manipulate the header
====
The flat format also defines the stack size for an application as a field in the flat header. To increase the stack allocated to an application, a simple change of this field is all that is required. This can be done with the flthdr command, like this:
flthdr -s  flat-executable

The flat format also allows two compression options. The entire executable can be compressed, providing maximum ROM savings. It also offers the often useful side effect that the application is loaded entirely into a contiguous RAM block. You also may choose data-segment-only compression. This is important if you want to save ROM space but still want the option to utilize XIP. The following:

flthdr -z flat-executable
  creates a fully compressed executable, and

flthdr -d flat-executable
  compresses only the data segment.
====
                              ...MaTed

Larry Baker
US Geological Survey
650-329-5608
ba...@usgs.gov <mailto:ba...@usgs.gov>



On 23 Jan 2014, at 1:15 AM, Angelo Dureghello wrote:

Dear all,

i have a small board with a coldfire mcf5307, 4 MB flash and 16MB sdram.

I have loaded on it this ucLinux:

~ # cat /proc/version
uClinux version 2.6.36.2 (angelo@angel3) (gcc version 4.6.1 (Sourcery CodeBench Lite 2011.09-23) ) #122 Fri Dec 14 23:52:01 CET 2012

I am now trying to upload and run a simple c++ program, with just 3 simple classes,
and a main().

Fist issue,

I tried to use the most recent uclinux.org <http://uclinux.org/> supplied toolchanin (m68k-uclinux-20101118),
i get :

make
/usr/local/bin/m68k-uclinux-g++ -O2 --pipe -m5307 -Iinclude -Wall -c -o obj/base64.o src/base64.cc /usr/local/bin/m68k-uclinux-g++ -O2 --pipe -m5307 -Iinclude -Wall -c -o obj/main.o src/main.cc /usr/local/bin/m68k-uclinux-g++ -O2 --pipe -m5307 -Iinclude -Wall -c -o obj/sha256.o src/sha256.cc /usr/local/bin/m68k-uclinux-g++ obj/base64.o obj/main.o obj/sha256.o -m5307 -o bin/cfbm -Wl,-Map,bin/cfbm.map
ERROR: text=0x1c100 overlaps data=0x0 ?
collect2: ld returned 1 exit status
make: *** [bin/cfbm] Error 1

Surfing the net, i don't find any good explaination to this, and the common workaround
suggested is to use the CodeSourcery toolchain.
So as a first thing i was wondering if the uclinux "user" folder does contain some cpp
projects, how do they compile ?

Then i moved to the CodeSourcery toolchain, that i copied from an old hard disk, since seems is not free to download anymore, is it ? Are there any alternative ?


With this toolchain strange things happen, until a certain point, adding code, everything works fine, program is correctly compiled on my host and executed on the board. Then, strangely, as the code increase, the program execution crash (without errors on console) and paralize the system. As i remove (comment out) some lines, ini random places, program
start to work correctly again.
So for now, also the CodeSourcery toolchain solution is not helping me.

I have now the suspect that uClinux itself has not been correctly configured, or that i am suffering for my 16MB of ram, even if i see 6,8MB still free before executing.

~ # cat /proc/meminfo
MemTotal:          13684 kB
MemFree:            6984 kB
Buffers:              16 kB
Cached:              144 kB
SwapCached:            0 kB
Active:               64 kB
Inactive:             48 kB
Active(anon):          0 kB
Inactive(anon):        0 kB
Active(file):         64 kB
Inactive(file):       48 kB
Unevictable:           0 kB
Mlocked:               0 kB
MmapCopy:            412 kB
SwapTotal:             0 kB
SwapFree:              0 kB
Dirty:                40 kB
Writeback:             0 kB
AnonPages:             0 kB
Mapped:                0 kB
Shmem:                 0 kB
Slab:               1292 kB
SReclaimable:         64 kB
SUnreclaim:         1228 kB
KernelStack:         108 kB
PageTables:            0 kB
NFS_Unstable:          0 kB
Bounce:                0 kB
WritebackTmp:          0 kB
CommitLimit:        6840 kB
Committed_AS:          0 kB
VmallocTotal:          0 kB
VmallocUsed:           0 kB
VmallocChunk:          0 kB


I don't know actually how to move, every help is accepted.

Many thanks,
angelo






_______________________________________________
uClinux-dev mailing list
uClinux-dev@uclinux.org <mailto:uClinux-dev@uclinux.org>
http://mailman.uclinux.org/mailman/listinfo/uclinux-dev
This message was resent by uclinux-dev@uclinux.org
To unsubscribe see:
http://mailman.uclinux.org/mailman/options/uclinux-dev




_______________________________________________
uClinux-dev mailing list
uClinux-dev@uclinux.org
http://mailman.uclinux.org/mailman/listinfo/uclinux-dev
This message was resent by uclinux-dev@uclinux.org
To unsubscribe see:
http://mailman.uclinux.org/mailman/options/uclinux-dev

Reply via email to