Hi, On 02/09/14 21:40, GravyFace wrote: > Got it to build and boot, finally: I had hit spacebar in menuconfig, but it > put an "M" not an "asterisk" under the RAM option, so I guess the sub-items I > had selected (DEV_BLK_RAM*) are ignored. > > Getting to busybox shell with: > > Loading network drivers. > modprobe: module ixp400 not found > modprobe: failed to load module ixp400 > /etc/rc: line 25: cannot create /dev/ixNpe: Read-only file system > modprobe: module ixp400_eth not found > modprobe: failed to load module ixp400_eth > > Assuming network drivers are missing? Included all the PHY drivers; > beboppin' and scattin' all over the place here, but having fun doing so!
Yep, the network drivers. That code base expects to use the Intel IXP4xx Access Library code - and you have to get that from Intel (it is not open source). It used to be the case that you could get a patch to use the IXP4xx access library code with the snapgear source on their www.snapgear.org web site. But that doesn't appear to respond any more. Regards Greg > On Mon, Sep 1, 2014 at 10:36 AM, GravyFace <gravyf...@gmail.com > <mailto:gravyf...@gmail.com>> wrote: > > Ok, that built ok, but same thing: hangs at "Using base address > 0x00400000 and length 0x000c65f8". > > Here's ~/snapgear-4.0.7/.config (without commented lines): > > CONFIG_DISTVERSION="4.0" > CONFIG_DEFAULTS_SECURECOMPUTING=y > CONFIG_DEFAULTS_SECURECOMPUTING_SG560=y > CONFIG_DEFAULTS_KERNEL_2_6=y > CONFIG_DEFAULTS_LIBC_UCLIBC=y > CONFIG_VENDOR=SecureComputing > CONFIG_PRODUCT=SG560 > CONFIG_LINUXDIR=linux-2.6.x > CONFIG_LIBCDIR=uClibc > > And here's ~/snapgear-4.0.7/config/.config (without commented lines): > > CONFIG_DISTVERSION="4.0" > CONFIG_LIB_LIBSSL=y > CONFIG_LIB_LIBGMP=y > CONFIG_LIB_LIBPAM=y > CONFIG_LIB_LIBPCAP=y > CONFIG_LIB_ZLIB=y > CONFIG_LIB_LIBUPNP=y > CONFIG_LIB_LIBNL=y > CONFIG_LIB_LIBNL_COMPONENTS=y > CONFIG_LIB_LIBNL_RTNL=y > CONFIG_LIB_LIBNL_ROUTE_LINK=y > CONFIG_LIB_LIBNL_NETFILTER=y > CONFIG_LIB_LIBNL_NETFILTER_CT=y > CONFIG_LIB_LIBNL_NETFILTER_LOG=y > CONFIG_LIB_NFNETLINK=y > CONFIG_LIB_NETFILTER_CONNTRACK=y > CONFIG_LIB_OSIP2=y > CONFIG_USER_INIT_INIT=y > CONFIG_USER_INIT_CONSOLE_SH=y > CONFIG_USER_INIT_RUN_FIREWALL=y > CONFIG_USER_OTHER_SH=y > CONFIG_USER_GETTYD_GETTYD=y > CONFIG_USER_CRON_CRON=y > CONFIG_USER_HWCLOCK_HWCLOCK=y > CONFIG_USER_FLASHW_FLASHW=y > CONFIG_USER_SETMAC_SETMAC=y > CONFIG_USER_NETFLASH_NETFLASH=y > CONFIG_USER_NETFLASH_WITH_FTP=y > CONFIG_USER_NETFLASH_WITH_CGI=y > CONFIG_USER_NETFLASH_VERSION=y > CONFIG_USER_NETFLASH_DECOMPRESS=y > CONFIG_USER_FLATFSD_FLATFSD=y > CONFIG_USER_FLATFSD_AUTO=y > CONFIG_USER_FLATFSD_COMPRESSED=y > CONFIG_USER_FLATFSD_HAS_RTC=y > CONFIG_USER_FLATFSD_EXTERNAL_INIT=y > CONFIG_USER_TRUSTEDSOURCE=y > CONFIG_USER_FNORD_HTTPD=y > CONFIG_USER_FNORD_PAM=y > CONFIG_USER_FNORD_404_REDIR=y > CONFIG_USER_BPALOGIN_BPALOGIN=y > CONFIG_USER_BRCTL_BRCTL=y > CONFIG_USER_CLAMAV_CLAMSMTP=y > CONFIG_USER_CONNTRACK_CONNTRACK=y > CONFIG_USER_DHCPCD_NEW_DHCPCD=y > CONFIG_USER_DHCP_ISC_SERVER_DHCPD=y > CONFIG_USER_DHCP_ISC_RELAY_DHCRELAY=y > CONFIG_USER_DIALD_DIALD=y > CONFIG_USER_DISCARD_DISCARD=y > CONFIG_USER_DISCARD_NO_INSTALL=y > CONFIG_USER_DISCARD_INETD_ECHO=y > CONFIG_USER_DISCARD_ECHO_NO_INSTALL=y > CONFIG_USER_DNSMASQ_DNSMASQ=y > CONFIG_USER_DNSMASQ2_DNSMASQ2=y > CONFIG_USER_DNSMASQ2_RESOLVE_AS_SERVER=y > CONFIG_USER_ETHERWAKE=y > CONFIG_USER_EZIPUPDATE_EZIPUPDATE=y > CONFIG_USER_OPENSWAN=y > CONFIG_USER_OPENSWAN_PLUTO_PLUTO=y > CONFIG_USER_OPENSWAN_PLUTO_WHACK=y > CONFIG_USER_OPENSWAN_UTILS_RANBITS=y > CONFIG_USER_OPENSWAN_UTILS_RSASIGKEY=y > CONFIG_USER_OPENSWAN_KLIPS_EROUTE=y > CONFIG_USER_OPENSWAN_KLIPS_KLIPSDEBUG=y > CONFIG_USER_OPENSWAN_KLIPS_SPI=y > CONFIG_USER_OPENSWAN_KLIPS_SPIGRP=y > CONFIG_USER_OPENSWAN_KLIPS_TNCFG=y > CONFIG_USER_OPENSWAN_PROGRAMS_LWDNSQ=y > CONFIG_USER_HTTPTUNNEL_CLIENT=y > CONFIG_USER_HTTPTUNNEL_SERVER=y > CONFIG_USER_INETD_INETD=y > CONFIG_USER_IPROUTE2=y > CONFIG_USER_IPROUTE2_TC_TC=y > CONFIG_USER_IPROUTE2_IP_IP=y > CONFIG_USER_IPROUTE2_IP_ROUTEF=y > CONFIG_USER_IPROUTE2_IP_ROUTEL=y > CONFIG_USER_IPROUTE2_IP_RTACCT=y > CONFIG_USER_IPROUTE2_IP_RTMON=y > CONFIG_USER_IPSET_IPSET=y > CONFIG_USER_IPTABLES_IPTABLES=y > CONFIG_USER_LAYER7_PROTOCOLS=y > CONFIG_USER_IPUTILS_IPUTILS=y > CONFIG_USER_IPUTILS_PING=y > CONFIG_USER_IPUTILS_TRACEPATH=y > CONFIG_USER_L2TPD_L2TPD=y > CONFIG_USER_LINUXIGD_LINUXIGD=y > CONFIG_USER_SMTP_SMTPCLIENT=y > CONFIG_USER_NETSNMP_SNMPD=y > CONFIG_USER_NTPD_NTPD=y > CONFIG_USER_NTPD_NTPDATE=y > CONFIG_USER_NTPD_NTPQ=y > CONFIG_USER_PPPD_PPPD_PPPD=y > CONFIG_USER_PPPD_WITH_PAM=y > CONFIG_USER_PPPD_WITH_MPPE=y > CONFIG_USER_PPPD_WITH_TACACS=y > CONFIG_USER_PPPD_WITH_RADIUS=y > CONFIG_USER_PPPD_WITH_PPPOE=y > CONFIG_USER_PPPD_PPPOE_RETRIES=5 > CONFIG_USER_PPPD_NO_AT_REDIRECTION=y > CONFIG_USER_PPTPD_PPTPCTRL=y > CONFIG_USER_PPTPD_PPTPD=y > CONFIG_USER_PPTP_PPTP=y > CONFIG_USER_QUAGGA_ZEBRA_ZEBRA=y > CONFIG_USER_QUAGGA_BGPD_BGPD=y > CONFIG_USER_QUAGGA_RIPD_RIPD=y > CONFIG_USER_RADAUTH_RADAUTH=y > CONFIG_USER_SIPROXD_SIPROXD=y > CONFIG_USER_TCPDUMP_TCPDUMP=y > CONFIG_USER_TELNETD_TELNETD=y > CONFIG_USER_TRACEROUTE_TRACEROUTE=y > CONFIG_USER_NET_TOOLS_ARP=y > CONFIG_USER_NET_TOOLS_HOSTNAME=y > CONFIG_USER_NET_TOOLS_IFCONFIG=y > CONFIG_USER_NET_TOOLS_NETSTAT=y > CONFIG_USER_NET_TOOLS_ROUTE=y > CONFIG_USER_NET_TOOLS_MII_TOOL=y > CONFIG_USER_CHAT_CHAT=y > CONFIG_USER_HD_HD=y > CONFIG_USER_RRDTOOL_RRDTOOL=y > CONFIG_USER_SHADOW_UTILS=y > CONFIG_USER_SHADOW_PAM=y > CONFIG_USER_SHADOW_LOGIN=y > CONFIG_LIB_TINYTCL=y > CONFIG_USER_TIP_TIP=y > CONFIG_USER_PROCPS_SYSCTL=y > CONFIG_USER_BUSYBOX_BUSYBOX=y > CONFIG_USER_BUSYBOX_HAVE_DOT_CONFIG=y > CONFIG_USER_BUSYBOX_SHOW_USAGE=y > CONFIG_USER_BUSYBOX_FEATURE_VERBOSE_USAGE=y > CONFIG_USER_BUSYBOX_FEATURE_COMPRESS_USAGE=y > CONFIG_USER_BUSYBOX_GETOPT_LONG=y > CONFIG_USER_BUSYBOX_FEATURE_DEVPTS=y > CONFIG_USER_BUSYBOX_BUSYBOX_EXEC_PATH="/proc/self/exe" > CONFIG_USER_BUSYBOX_FEATURE_SYSLOG=y > CONFIG_USER_BUSYBOX_NO_DEBUG_LIB=y > CONFIG_USER_BUSYBOX_INCLUDE_SUSv2=y > CONFIG_USER_BUSYBOX_INSTALL_APPLET_SYMLINKS=y > CONFIG_USER_BUSYBOX_PREFIX="./_install" > CONFIG_USER_BUSYBOX_PASSWORD_MINLEN=6 > CONFIG_USER_BUSYBOX_MD5_SIZE_VS_SPEED=1 > CONFIG_USER_BUSYBOX_FEATURE_EDITING=y > CONFIG_USER_BUSYBOX_FEATURE_EDITING_MAX_LEN=1024 > CONFIG_USER_BUSYBOX_FEATURE_EDITING_HISTORY=15 > CONFIG_USER_BUSYBOX_FEATURE_TAB_COMPLETION=y > CONFIG_USER_BUSYBOX_FEATURE_COPYBUF_KB=4 > CONFIG_USER_BUSYBOX_MONOTONIC_SYSCALL=y > CONFIG_USER_BUSYBOX_IOCTL_HEX2STR_ERROR=y > CONFIG_USER_BUSYBOX_CAT=y > CONFIG_USER_BUSYBOX_CHGRP=y > CONFIG_USER_BUSYBOX_CHMOD=y > CONFIG_USER_BUSYBOX_CHOWN=y > CONFIG_USER_BUSYBOX_CP=y > CONFIG_USER_BUSYBOX_DATE=y > CONFIG_USER_BUSYBOX_FEATURE_DATE_ISOFMT=y > CONFIG_USER_BUSYBOX_DD=y > CONFIG_USER_BUSYBOX_DF=y > CONFIG_USER_BUSYBOX_FEATURE_DF_INODE=y > CONFIG_USER_BUSYBOX_DIRNAME=y > CONFIG_USER_BUSYBOX_DU=y > CONFIG_USER_BUSYBOX_FEATURE_DU_DEFAULT_BLOCKSIZE_1K=y > CONFIG_USER_BUSYBOX_ECHO=y > CONFIG_USER_BUSYBOX_ENV=y > CONFIG_USER_BUSYBOX_FALSE=y > CONFIG_USER_BUSYBOX_HEAD=y > CONFIG_USER_BUSYBOX_LN=y > CONFIG_USER_BUSYBOX_LS=y > CONFIG_USER_BUSYBOX_FEATURE_LS_FILETYPES=y > CONFIG_USER_BUSYBOX_FEATURE_LS_FOLLOWLINKS=y > CONFIG_USER_BUSYBOX_FEATURE_LS_RECURSIVE=y > CONFIG_USER_BUSYBOX_FEATURE_LS_SORTFILES=y > CONFIG_USER_BUSYBOX_FEATURE_LS_TIMESTAMPS=y > CONFIG_USER_BUSYBOX_FEATURE_LS_USERNAME=y > CONFIG_USER_BUSYBOX_MKDIR=y > CONFIG_USER_BUSYBOX_MKFIFO=y > CONFIG_USER_BUSYBOX_MKNOD=y > CONFIG_USER_BUSYBOX_MV=y > CONFIG_USER_BUSYBOX_PWD=y > CONFIG_USER_BUSYBOX_RM=y > CONFIG_USER_BUSYBOX_RMDIR=y > CONFIG_USER_BUSYBOX_SLEEP=y > CONFIG_USER_BUSYBOX_SYNC=y > CONFIG_USER_BUSYBOX_TAIL=y > CONFIG_USER_BUSYBOX_FEATURE_FANCY_TAIL=y > CONFIG_USER_BUSYBOX_TEST=y > CONFIG_USER_BUSYBOX_TOUCH=y > CONFIG_USER_BUSYBOX_TRUE=y > CONFIG_USER_BUSYBOX_UNAME=y > CONFIG_USER_BUSYBOX_FEATURE_AUTOWIDTH=y > CONFIG_USER_BUSYBOX_FEATURE_HUMAN_READABLE=y > CONFIG_USER_BUSYBOX_CMP=y > CONFIG_USER_BUSYBOX_SED=y > CONFIG_USER_BUSYBOX_VI=y > CONFIG_USER_BUSYBOX_FEATURE_VI_MAX_LEN=4096 > CONFIG_USER_BUSYBOX_FEATURE_VI_8BIT=y > CONFIG_USER_BUSYBOX_FEATURE_VI_COLON=y > CONFIG_USER_BUSYBOX_FEATURE_VI_YANKMARK=y > CONFIG_USER_BUSYBOX_FEATURE_VI_SEARCH=y > CONFIG_USER_BUSYBOX_FEATURE_VI_USE_SIGNALS=y > CONFIG_USER_BUSYBOX_FEATURE_VI_DOT_CMD=y > CONFIG_USER_BUSYBOX_FEATURE_VI_READONLY=y > CONFIG_USER_BUSYBOX_FEATURE_VI_SETOPTS=y > CONFIG_USER_BUSYBOX_FEATURE_VI_SET=y > CONFIG_USER_BUSYBOX_FEATURE_VI_WIN_RESIZE=y > CONFIG_USER_BUSYBOX_FEATURE_VI_OPTIMIZE_CURSOR=y > CONFIG_USER_BUSYBOX_FEATURE_ALLOW_EXEC=y > CONFIG_USER_BUSYBOX_HALT=y > CONFIG_USER_BUSYBOX_INSMOD=y > CONFIG_USER_BUSYBOX_RMMOD=y > CONFIG_USER_BUSYBOX_LSMOD=y > CONFIG_USER_BUSYBOX_MODPROBE=y > CONFIG_USER_BUSYBOX_FEATURE_MODPROBE_MULTIPLE_OPTIONS=y > CONFIG_USER_BUSYBOX_FEATURE_MODPROBE_FANCY_ALIAS=y > CONFIG_USER_BUSYBOX_FEATURE_CHECK_TAINTED_MODULE=y > CONFIG_USER_BUSYBOX_FEATURE_2_6_MODULES=y > CONFIG_USER_BUSYBOX_MORE=y > CONFIG_USER_BUSYBOX_FEATURE_USE_TERMIOS=y > CONFIG_USER_BUSYBOX_MOUNT=y > CONFIG_USER_BUSYBOX_FEATURE_MOUNT_FLAGS=y > CONFIG_USER_BUSYBOX_UMOUNT=y > CONFIG_USER_BUSYBOX_FEATURE_UMOUNT_ALL=y > CONFIG_USER_BUSYBOX_FEATURE_MOUNT_LOOP=y > CONFIG_USER_BUSYBOX_WATCHDOGD=y > CONFIG_USER_BUSYBOX_ARPING=y > CONFIG_USER_BUSYBOX_FREE=y > CONFIG_USER_BUSYBOX_KILL=y > CONFIG_USER_BUSYBOX_PS=y > CONFIG_USER_BUSYBOX_UPTIME=y > CONFIG_USER_BUSYBOX_FEATURE_SH_IS_ASH=y > CONFIG_USER_BUSYBOX_ASH=y > CONFIG_USER_BUSYBOX_ASH_OPTIMIZE_FOR_SIZE=y > CONFIG_USER_BUSYBOX_SYSLOGD=y > CONFIG_USER_BUSYBOX_FEATURE_ROTATE_LOGFILE=y > CONFIG_USER_BUSYBOX_FEATURE_REMOTE_LOG=y > CONFIG_USER_BUSYBOX_KLOGD=y > CONFIG_USER_RAMIMAGE_NONE=y > CONFIG_POOR_ENTROPY=y > > > > > On Mon, Sep 1, 2014 at 8:51 AM, GravyFace <gravyf...@gmail.com > <mailto:gravyf...@gmail.com>> wrote: > > Hi, > > I'm using gcc version 4.6.3 > > Oddly, now I can't build with kernel config I have: threw two > separate errors, one was a complaint of line X in the dhclient configuration, > lastly was a lex error of some nondescript reasoning. I tried again with > make clean, no dice, so clearly fingers of the rotund persuasion are wreaking > havoc in the kernel config. I blew away my snapgear directory, extracting > tarball, trying again from scratch now. > > > On Mon, Sep 1, 2014 at 1:05 AM, Greg Ungerer <g...@uclinux.org > <mailto:g...@uclinux.org>> wrote: > > Hi, > > On 31/08/14 13:49, GravyFace wrote: > > Update: I was able to (I think) sort out the kernel config by > using make menuconfig and with the help of search (/), find the parameters > suggested, change them, and re-build the image. Unfortunately it seems as > though these kernel config options aren't correct: it just hangs after "using > base address...". > > Can you post your modified kernel config here? > > I took the 4.0.7 source, modified kernel config to enable those > settings, and that network loads, boots and runs for me on a > SG560. > > I am using a new compiler version, not sure if that might be an > issue. > (I am using a gcc-4.2.1 toolchain). > > Regards > Greg > > > > > Recovery Bootloader > > (C) Copyright 1999-2006, Secure Computing Inc > (www.securecomputing.com <http://www.securecomputing.com> > <http://www.securecomputing.com>) > > SecureComputing/SG560 Version 3.1.5u1 > > 'n'etwork, 'f'lash, 's'erial [n] : > > Timeout, initiating network > > Decompressing etherboot > > +Getting DHCP address... . > > Ethernet eth0: MAC address > 00:d0:cf:0b:b9:34 > > IP: 192.168.0.101/255.255.255.0 > <http://192.168.0.101/255.255.255.0> <http://192.168.0.101/255.255.255.0>, > Gateway: 192.168.0.1 > > Default server: 192.168.0.254, DNS server IP: 0.0.0.0 > > > > RedBoot(tm) bootstrap and debug environment [RAM] > > Red Hat certified release, version 1.94 - built 16:02:10, Nov > 4 2005 > > > > Platform: CyberGuard SG5XX family of VPN/Firewall/Routers > (XScale) BE > > Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc. > > > > RAM: 0x00000000-0x01000000, 0x00060d48-0x00ff3000 available > > == Executing boot script in 1.000 seconds - enter ^C to abort > > RedBoot> load -v -s 0x00200000 -b 0x00800000 image.bin > > Using default protocol (TFTP) > > | > > Raw file loaded 0x00200000-0x002c65f8, assumed entry at > 0x00200000 > > RedBoot> exec -r 0x00800000 -c "console=ttyS0,115200 > root=/dev/ram0" 0x00200000 > > [Using ramdisk at 0x800000-0xbcf000] > > Using base address 0x00200000 and length 0x000c65fc > > > > > > Power light and the port lights are solid. > > > > > > On Sat, Aug 30, 2014 at 8:20 PM, GravyFace <gravyf...@gmail.com > <mailto:gravyf...@gmail.com> <mailto:gravyf...@gmail.com > <mailto:gravyf...@gmail.com>>> wrote: > > > > Hi Greg, > > > > Searched online for where to place those kernel config > entries; tried to add them to the symlink'ed config.arch in the root > snapgear-4.0.7 directory but that made 'make' unhappy. > > > > Where should I be placing those config lines? There's > oodles of files with similar "CONFIG_" lines, so not sure where I should be > putting it. > > > > Thanks > > > > > > On Fri, Aug 29, 2014 at 2:28 AM, Greg Ungerer > <g...@uclinux.org <mailto:g...@uclinux.org> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org>>> wrote: > > > > > > Hi, > > > > On 29/08/14 00:09, GravyFace wrote: > > > Sure, here you go: > > > > > > Recovery Bootloader > > > (C) Copyright 1999-2006, Secure Computing Inc > (www.securecomputing.com <http://www.securecomputing.com> > <http://www.securecomputing.com> <http://www.securecomputing.com>) > > > SecureComputing/SG560 Version 3.1.5u1 > > > 'n'etwork, 'f'lash, 's'erial [n] : > > > Recovery Bootloader > > > (C) Copyright 1999-2006, Secure Computing Inc > (www.securecomputing.com <http://www.securecomputing.com> > <http://www.securecomputing.com> <http://www.securecomputing.com>) > > > SecureComputing/SG560 Version 3.1.5u1 > > > 'n'etwork, 'f'lash, 's'erial [n] : > > > Timeout, initiating network > > > Decompressing etherboot > > > +Getting DHCP address... . > > > Ethernet eth0: MAC address > 00:d0:cf:0b:b9:34 > > > IP: 192.168.0.101/255.255.255.0 > <http://192.168.0.101/255.255.255.0> <http://192.168.0.101/255.255.255.0> > <http://192.168.0.101/255.255.255.0>, Gateway: 192.168.0.1 > > > Default server: 192.168.0.254, DNS server IP: 0.0.0.0 > > > > > > RedBoot(tm) bootstrap and debug environment [RAM] > > > Red Hat certified release, version 1.94 - built > 16:02:10, Nov 4 2005 > > > > > > Platform: CyberGuard SG5XX family of > VPN/Firewall/Routers (XScale) BE > > > Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, > Inc. > > > > > > RAM: 0x00000000-0x01000000, 0x00060d48-0x00ff3000 > available > > > == Executing boot script in 1.000 seconds - enter ^C > to abort > > > RedBoot> load -v -s 0x00200000 -b 0x00800000 image.bin > > > Using default protocol (TFTP) > > > | > > > Raw file loaded 0x00200000-0x002c4b8c, assumed entry > at 0x00200000 > > > RedBoot> exec -r 0x00800000 -c "console=ttyS0,115200 > root=/dev/ram0" 0x00200000 > > > [Using ramdisk at 0x800000-0xbce000] > > > Using base address 0x00200000 and length 0x000c4b90 > > > Linux version 2.6.26-uc0 (root@test-ubu01) (gcc > version 3.4.4) #13 Tue Aug 26 12:14:17 EDT 2014 > > > CPU: XScale-IXP42x Family [690541f2] revision 2 > (ARMv5TE), cr=000039ff > > > Machine: McAfee/SG560 > > > Memory policy: ECC disabled, Data cache writeback > > > CPU0: D VIVT undefined 5 cache > > > CPU0: I cache: 32768 bytes, associativity 32, 32 byte > lines, 32 sets > > > CPU0: D cache: 32768 bytes, associativity 32, 32 byte > lines, 32 sets > > > Built 1 zonelists in Zone order, mobility grouping > off. Total pages: 4064 > > > Kernel command line: console=ttyS0,115200 > root=/dev/ram0 > > > PID hash table entries: 64 (order: 6, 256 bytes) > > > Dentry cache hash table entries: 2048 (order: 1, 8192 > bytes) > > > Inode-cache hash table entries: 1024 (order: 0, 4096 > bytes) > > > Memory: 16MB = 16MB total > > > Memory: 14616KB available (1428K code, 96K data, 60K > init) > > > SLUB: Genslabs=12, HWalign=32, Order=0-3, > MinObjects=0, CPUs=1, Nodes=1 > > > Mount-cache hash table entries: 512 > > > CPU: Testing write buffer coherency: ok > > > net_namespace: 484 bytes > > > NET: Registered protocol family 16 > > > IXP4xx: Using 16MiB expansion bus window size > > > NET: Registered protocol family 2 > > > IP route cache hash table entries: 1024 (order: 0, > 4096 bytes) > > > TCP established hash table entries: 512 (order: 0, > 4096 bytes) > > > TCP bind hash table entries: 1024 (order: 0, 4096 > bytes) > > > TCP: Hash tables configured (established 512 bind > 1024) > > > TCP reno registered > > > NET: Registered protocol family 1 > > > NetWinder Floating Point Emulator V0.97 (double > precision) > > > Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 > Phillip Lougher > > > Squashfs 2.2 includes LZMA decompression support > > > io scheduler noop registered (default) > > > ledman: Copyright (C) SnapGear, 2000-2008. > > > LED: registered ERASE switch on IRQ26 > > > M41T11M6: Real Time Clock driver > > > snapdog: HW/SW watchdog timer for SnapGear/Others > > > Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, > IRQ sharing disabled > > > serial8250.0: ttyS0 at MMIO 0xc8000000 (irq = 15) is > a XScale > > > console [ttyS0] enabled > > > serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is > a XScale > > > PPP generic driver version 2.4.2 > > > PPP Deflate Compression module registered > > > PPP BSD Compression module registered > > > PPP MPPE Compression module registered > > > NET: Registered protocol family 24 > > > SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic > channels, max=256). > > > CSLIP: code copyright 1989 Regents of the University > of California. > > > SnapGear: MTD flash setup > > > SnapGear Intel/StrataFlash: Found 1 x16 devices at > 0x0 in 16-bit bank > > > Intel/Sharp Extended Query Table at 0x0031 > > > Using buffer write method > > > cfi_cmdset_0001: Erase suspend on write enabled > > > SnapGear: SnapGear Intel/StrataFlash device size = > 8192K > > > Creating 6 MTD partitions on "SnapGear > Intel/StrataFlash": > > > 0x00000000-0x00020000 : "SnapGear Boot Loader" > > > 0x00020000-0x000a0000 : "SnapGear non-volatile > configuration" > > > 0x000a0000-0x007e0000 : "SnapGear image" > > > 0x00000000-0x00800000 : "SnapGear Intel/StrataFlash" > > > 0x007e0000-0x00800000 : "SnapGear System Log" > > > 0x007e0000-0x00800000 : "SnapGear System Log" > > > SNAPARM: root device set to 2 > > > u32 classifier > > > GRE over IPv4 tunneling driver > > > TCP cubic registered > > > NET: Registered protocol family 17 > > > Bridge firewalling registered > > > 802.1Q VLAN Support v1.8 Ben Greear > <gree...@candelatech.com <mailto:gree...@candelatech.com> > <mailto:gree...@candelatech.com <mailto:gree...@candelatech.com>> > <mailto:gree...@candelatech.com <mailto:gree...@candelatech.com> > <mailto:gree...@candelatech.com <mailto:gree...@candelatech.com>>>> > > > All bugs added by David S. Miller <da...@redhat.com > <mailto:da...@redhat.com> <mailto:da...@redhat.com <mailto:da...@redhat.com>> > <mailto:da...@redhat.com <mailto:da...@redhat.com> <mailto:da...@redhat.com > <mailto:da...@redhat.com>>>> > > > XScale DSP coprocessor detected. > > > VFS: Cannot open root device "ram0" or > unknown-block(0,0) > > > Please append a correct "root=" boot option; here are > the available partitions: > > > 1f00 128 mtdblock0 (driver?) > > > 1f01 512 mtdblock1 (driver?) > > > 1f02 7424 mtdblock2 (driver?) > > > 1f03 8192 mtdblock3 (driver?) > > > 1f04 128 mtdblock4 (driver?) > > > 1f05 128 mtdblock5 (driver?) > > > Kernel panic - not syncing: VFS: Unable to mount root > fs on unknown-block(0,0) > > > > I suspect you need these enabled: > > > > CONFIG_BLK_DEV_INITRD=y > > CONFIG_BLK_DEV_RAM=y > > CONFIG_BLK_DEV_RAM_COUNT=4 > > CONFIG_BLK_DEV_RAM_SIZE=16384 > > > > Doesn't look like they are on from the output above. > > Otherwise it looks ok. > > > > Regards > > Greg > > > > > > > > > On Wed, Aug 27, 2014 at 8:02 PM, Greg Ungerer > <g...@uclinux.org <mailto:g...@uclinux.org> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org>> <mailto:g...@uclinux.org <mailto:g...@uclinux.org> > <mailto:g...@uclinux.org <mailto:g...@uclinux.org>>>> wrote: > > > > > > On 27/08/14 23:09, GravyFace wrote: > > > > > > On Tue, Aug 26, 2014 at 8:44 PM, Greg Ungerer > <g...@uclinux.org <mailto:g...@uclinux.org> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org>> <mailto:g...@uclinux.org <mailto:g...@uclinux.org> > <mailto:g...@uclinux.org <mailto:g...@uclinux.org>>> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org> <mailto:g...@uclinux.org <mailto:g...@uclinux.org>> > <mailto:g...@uclinux.org <mailto:g...@uclinux.org> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org>>>>> wrote: > > > I'm assuming this was the last step, > > > > > > That is the last step. Easiest fix is to > just create a /tftpboot > > > directory that is world read/write. > Doesn't really matter whether > > > you actually have tftp server enabled or > not. > > > > > > Yeah, I was able to figure that out and with > the help of the SG manual (amazing, those!) found out about the "recovery" > process of holding down ERASE and booting. With Wireshark, I was able to see > it pick up an IP from tftpd's DHCP service and successfully download my > image.bin. > > > > > > > > > Maybe, maybe not. What are the front LEDs > doing? > > > If the heartbeat (HB) is flashing then it > was probably successful. > > > > > > A serial port console is not enabled by > default, so you won't get > > > anything on the serial port without doing > extra steps. > > > > > > Now that I have that out of my > system, my next step is to install tftpd and (I'm assuming) do a TFTP based > install? Don't see that part on the snapgear.org <http://snapgear.org> > <http://snapgear.org> <http://snapgear.org> <http://snapgear.org> > <http://snapgear.org> documentation on archive.org <http://archive.org> > <http://archive.org> <http://archive.org> <http://archive.org> > <http://archive.org>, but maybe I'm missing something. > > > > > > > > > SnapGear has been shutdown so I don't > know they have on the web anymore. > > > But the tftp network load is pretty > simple. To see what is going on hook > > > up the serial port at 115200,8,n,1. Then > hold in the ERASE button and > > > plug in the power. It will come up with a > simple boot loader prompt. > > > After a few seconds it will timeout and > try a network load - doing a > > > dhcp address lookup and then trying a > tftp load of a system image > > > (that is the image.bin file that your > compile generated). > > > > > > > > > Well, getting a kernel panic; don't think it > can find the flash device... > > > > > > XScale DSP coprocessor detected. > > > VFS: Cannot open root device "ram0" or > unknown-block(0,0) > > > Please append a correct "root=" boot option; > here are the available partitions: > > > 1f00 128 mtdblock0 (driver?) > > > 1f01 512 mtdblock1 (driver?) > > > 1f02 7424 mtdblock2 (driver?) > > > 1f03 8192 mtdblock3 (driver?) > > > 1f04 128 mtdblock4 (driver?) > > > 1f05 128 mtdblock5 (driver?) > > > Kernel panic - not syncing: VFS: Unable to > mount root fs on unknown-block(0,0) > > > > > > > > > Can you send the complete boot log? > > > > > > > > > There was a patch that I never applied as I > wasn't sure what the architecture was for these, but seeing this in the boot > message ("CPU: XScale-IXP42x Family [690541f2] revision 2 (ARMv5TE), > cr=000039ff"), it jogged my memory of this, from the archive.org > <http://archive.org> <http://archive.org> <http://archive.org> > <http://archive.org>'s snapgear documentation page: > > > > > > > > > "Also available is a patch package that can > be used to build the Intel IXP4xx Access Library code as part of the SnapGear > distribution. This patch set contains support for the Intel CSR-1.4 with > DSR-2.6.2 combination, and the Intel CSR-2.4 library (on both 2.4 and 2.6 > linux kernels)." > > > > > > There's also this, but it appears as those > RedBoot has already been configured: > > > > https://gitorious.org/linux-__nios2/uclinux-dist/source/__5316285bb1b0a07bd2a2a562ec9397__af22dc465d:vendors/__SecureComputing/SG560/README > > <https://gitorious.org/linux-nios2/uclinux-dist/source/5316285bb1b0a07bd2a2a562ec9397af22dc465d:vendors/SecureComputing/SG560/README> > > > > > > > > > Before Linux had in kernel drivers for the IXP4xx > eth driver you > > > had to use Intel's drivers for them. That > SecureComputing/SG560 > > > config would have been configured with them in > mind. I don't recall > > > what kernel the Snapgear 4.0 source was based on, > but you may be > > > able to configure and use the kernels own ixp4xx > eth drivers. > > > > > > You can ignore what that README says about > redboot. It doesn't really > > > apply to the SG560. (The network boot loading is > done using a redboot, > > > but it is a stripped down simple one - that just > does the network > > > loading. It doesn't deal with flash). > > > > > > Regards > > > Greg > > > > > > > > > I would suggest hard setting a command > line in your kernel config so that > > > you have console=ttyS0,115200 set. > > > > > > I think I saw an old post on how to do that; > if I get past the kernel panic, this will be the first thing I do. > > > > > > Regards > > > Greg > > > > > > > > > > > > On Mon, Aug 25, 2014 at 9:40 AM, > GravyFace <gravyf...@gmail.com <mailto:gravyf...@gmail.com> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com>> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com>>> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com>> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com>>>> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com>> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com>>> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com>> > <mailto:gravyf...@gmail.com <mailto:gravyf...@gmail.com> > <mailto:gravyf...@gmail.com > <mailto:gravyf...@gmail.com>>>>>> wrote: > > > > > > Thanks, I'll give that a go now. > > > > > > > > > On Mon, Aug 25, 2014 at 2:24 AM, > Greg Ungerer <g...@uclinux.org <mailto:g...@uclinux.org> > <mailto:g...@uclinux.org <mailto:g...@uclinux.org>> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org>>> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org> <mailto:g...@uclinux.org <mailto:g...@uclinux.org>> > <mailto:g...@uclinux.org <mailto:g...@uclinux.org> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org>>>> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org> <mailto:g...@uclinux.org <mailto:g...@uclinux.org>> > <mailto:g...@uclinux.org <mailto:g...@uclinux.org> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org>>> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org> <mailto:g...@uclinux.org <mailto:g...@uclinux.org>> > <mailto:g...@uclinux.org <mailto:g...@uclinux.org> <mailto:g...@uclinux.org > <mailto:g...@uclinux.org>>>>>> wrote: > > > > > > Hi, > > > > > > > > > On 24/08/14 03:26, gravyface > wrote: > > > > > > Hi all, > > > > > > First time attempting to > compile really anything in Linux (why not try this? <g>), and hitting a wall > with a seemingly pam-auth related error. > > > > > > Build Environment: > > > > > > - Ubuntu Server 12.04.5 > LTS with apt versions of binutils, build-essentials, gcc, gdb, curses > (libncurses5-dev libncursesw5-dev). I downloaded the > arm-linux-tools-20061213.tar.______gz > <https://web.archive.org/web/______20100715203220/http://ftp.______snapgear.org/pub/snapgear/______tools/arm-linux/arm-linux-______tools-20061213.tar.gz > > <https://web.archive.org/web/____20100715203220/http://ftp.____snapgear.org/pub/snapgear/____tools/arm-linux/arm-linux-____tools-20061213.tar.gz> > > <https://web.archive.org/web/____20100715203220/http://ftp.____snapgear.org/pub/snapgear/____tools/arm-linux/arm-linux-____tools-20061213.tar.gz > > <https://web.archive.org/web/__20100715203220/http://ftp.__snapgear.org/pub/snapgear/__tools/arm-linux/arm-linux-__tools-20061213.tar.gz>> > > <https://web.archive.org/web/____20100715203220/http://ftp.____snapgear.org/pub/snapgear/____tools/arm-linux/arm-linux-____tools-20061213.tar.gz > > > > <https://web.archive.org/web/__20100715203220/http://ftp.__snapgear.org/pub/snapgear/__tools/arm-linux/arm-linux-__tools-20061213.tar.gz> > > <https://web.archive.org/web/__20100715203220/http://ftp.__snapgear.org/pub/snapgear/__tools/arm-linux/arm-linux-__tools-20061213.tar.gz > > <https://web.archive.org/web/20100715203220/http://ftp.snapgear.org/pub/snapgear/tools/arm-linux/arm-linux-tools-20061213.tar.gz>>>> > from Web Archive's copy, but have no idea how to use it. > > > > > > > > > > > > > > > I can get whatever > versions of packages needed; just let me know. > > > > > > Target: > > > > > > - I have more SG560s > than I know what to do with after dismantling a large site-to-site client > network; I'm interested in building simple network testing appliances > (ping/arp-scan/nc/ssh) I can use when configuring various networking devices, > so I think the default libraries and utilities should be more than adequate > in the base image. > > > > > > What I've done: > > > > > > - Extracted > http://ftp.snapgear.org/pub/______snapgear/src/snapgear-4.0.7.______tar.bz2 > <http://ftp.snapgear.org/pub/____snapgear/src/snapgear-4.0.7.____tar.bz2> > <http://ftp.snapgear.org/pub/____snapgear/src/snapgear-4.0.7.____tar.bz2 > <http://ftp.snapgear.org/pub/__snapgear/src/snapgear-4.0.7.__tar.bz2>> > <http://ftp.snapgear.org/pub/____snapgear/src/snapgear-4.0.7.____tar.bz2 > <http://ftp.snapgear.org/pub/__snapgear/src/snapgear-4.0.7.__tar.bz2> > <http://ftp.snapgear.org/pub/__snapgear/src/snapgear-4.0.7.__tar.bz2 > <http://ftp.snapgear.org/pub/snapgear/src/snapgear-4.0.7.tar.bz2>>> to my > home directory in a sub-folder called uclinux (full path is > /home/gravyface/uclinux/______snapgear-4.0.7). From that directory, ran > "make SecureComputing/SG560_default" which ran for 15 minutes or so, happily > compiling, until it exited with Error 2, and not a whole lot more: > > > > > > > > > > > > > > > By default the build is > parallel across the number of CPUs you have. > > > It may be that the actuall > error was way back in the compile output. > > > > > > Try running: > > > > > > make NON_SMP_BUILD=1 > SecureComputing/SG560_default > > > > > > It will be a lot slower, > only running on 1 CPU. But it will much > > > more likely stop at the > failure point. > > > > > > Regards > > > Greg > > > > > > > > > > > > ucfront-gcc > arm-linux-gcc -mbig-endian -mcpu=xscale -mtune=xscale -msoft-float > -DHOST_NAME_MAX=255 -shared .libs/pam_xauth.o -Wl,--rpath > -Wl,/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/libpam/.libs > -L/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/libpam > /home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/libpam/.libs/libpam.so > -mbig-endian -mcpu=xscale -mtune=xscale -msoft-float > -Wl,--version-script=../../../______modules/pam_xauth/../____modules.__map > -Wl,-S -Wl,-soname -Wl,pam_xauth.so -o .libs/pam_xauth.so > > > creating pam_xauth.la > <http://pam_xauth.la> <http://pam_xauth.la> <http://pam_xauth.la> > <http://pam_xauth.la> <http://pam_xauth.la> <http://pam_xauth.la/> > > > (cd .libs && rm -f > pam_xauth.la <http://pam_xauth.la> <http://pam_xauth.la> > <http://pam_xauth.la> <http://pam_xauth.la> <http://pam_xauth.la> > <http://pam_xauth.la/> && ln -s ../pam_xauth.la <http://pam_xauth.la> > <http://pam_xauth.la> <http://pam_xauth.la> <http://pam_xauth.la> > <http://pam_xauth.la> <http://pam_xauth.la/> pam_xauth.la > <http://pam_xauth.la> <http://pam_xauth.la> <http://pam_xauth.la> > <http://pam_xauth.la> <http://pam_xauth.la> <http://pam_xauth.la/>) > > > > > > make[8]: Leaving > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/modules/pam_xauth' > > > make[8]: Entering > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/modules' > > > > > > > > > make[8]: Nothing to be > done for `all-am'. > > > make[8]: Leaving > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/modules' > > > make[7]: Leaving > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/modules' > > > Making all in po > > > make[7]: Entering > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/po' > > > > > > > > > make[7]: Nothing to be > done for `all'. > > > make[7]: Leaving > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/po' > > > Making all in conf > > > make[7]: Entering > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/conf' > > > make[8]: Entering > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/conf' > > > > > > > > > make[8]: Nothing to be > done for `all-am'. > > > make[8]: Leaving > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/conf' > > > make[7]: Leaving > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build/conf' > > > make[7]: Entering > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build' > > > > > > > > > make[7]: Nothing to be > done for `all-am'. > > > make[7]: Leaving > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build' > > > make[6]: Leaving > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build' > > > make[5]: Leaving > directory > `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam/______build' > > > make[4]: Leaving > directory `/home/gravyface/uclinux/______snapgear-4.0.7/lib/libpam' > > > make[3]: Leaving > directory `/home/gravyface/uclinux/______snapgear-4.0.7/lib' > > > > > > > > > make[2]: *** [all] Error > 2 > > > make[2]: Leaving > directory `/home/gravyface/uclinux/______snapgear-4.0.7/lib' > > > > > > > > > make[1]: *** [subdirs] > Error 1 > > > make[1]: Leaving > directory `/home/gravyface/uclinux/______snapgear-4.0.7' > > > make: *** > [SecureComputing/SG560_______default] Error 2 > > > > > > > > > > > > > > > Looks to be pam-related, > but with no error, I'm kind of at a loss here. > > > > > > Thanks in advance! > > > > > > > > > > _____________________________________________________ > > > uClinux-dev mailing list > > > uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>>> <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>. <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>.>__org <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>>>> <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux> <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>>. <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux> <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>>.>____org <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>. <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>.>__org <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> > <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>>>>> > > > > http://mailman.uclinux.org/______mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/____mailman/listinfo/uclinux-dev> > <http://mailman.uclinux.org/____mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/__mailman/listinfo/uclinux-dev>> > <http://mailman.uclinux.org/____mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/__mailman/listinfo/uclinux-dev> > <http://mailman.uclinux.org/__mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/mailman/listinfo/uclinux-dev>>> > > > This message was resent > by uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>>> > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>. > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>.>__org > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>>>> > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux> > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>>. > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux> > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>>.>____org > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>. > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>.>__org > <mailto:uclinux-dev@uclinux.org > <mailto:uclinux-dev@uclinux.org> <mailto:uclinux-dev@uclinux.org > <mailto:uclinux-dev@uclinux.org>>>>> > > > To unsubscribe see: > > > > http://mailman.uclinux.org/______mailman/options/uclinux-dev > <http://mailman.uclinux.org/____mailman/options/uclinux-dev> > <http://mailman.uclinux.org/____mailman/options/uclinux-dev > <http://mailman.uclinux.org/__mailman/options/uclinux-dev>> > <http://mailman.uclinux.org/____mailman/options/uclinux-dev > <http://mailman.uclinux.org/__mailman/options/uclinux-dev> > <http://mailman.uclinux.org/__mailman/options/uclinux-dev > <http://mailman.uclinux.org/mailman/options/uclinux-dev>>> > > > > > > > > > > _____________________________________________________ > > > uClinux-dev mailing list > > > uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>>> <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>. <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>.>__org <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>>>> <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux> <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>>. <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux> <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>>.>____org <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>. <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>.>__org <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> > <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>>>>> > > > > http://mailman.uclinux.org/______mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/____mailman/listinfo/uclinux-dev> > <http://mailman.uclinux.org/____mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/__mailman/listinfo/uclinux-dev>> > <http://mailman.uclinux.org/____mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/__mailman/listinfo/uclinux-dev> > <http://mailman.uclinux.org/__mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/mailman/listinfo/uclinux-dev>>> > > > This message was resent by > uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>>> > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>. > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>.>__org > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>>>> > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux> > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>>. > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux> > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>>.>____org > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>. > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>.>__org > <mailto:uclinux-dev@uclinux.org > <mailto:uclinux-dev@uclinux.org> <mailto:uclinux-dev@uclinux.org > <mailto:uclinux-dev@uclinux.org>>>>> > > > To unsubscribe see: > > > > http://mailman.uclinux.org/______mailman/options/uclinux-dev > <http://mailman.uclinux.org/____mailman/options/uclinux-dev> > <http://mailman.uclinux.org/____mailman/options/uclinux-dev > <http://mailman.uclinux.org/__mailman/options/uclinux-dev>> > <http://mailman.uclinux.org/____mailman/options/uclinux-dev > <http://mailman.uclinux.org/__mailman/options/uclinux-dev> > <http://mailman.uclinux.org/__mailman/options/uclinux-dev > <http://mailman.uclinux.org/mailman/options/uclinux-dev>>> > > > > > > > > > > > > > > > > > > > > > > > > > ___________________________________________________ > > > uClinux-dev mailing list > > > uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>>> <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>. <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>.>__org <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>>>> > > > > http://mailman.uclinux.org/____mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/__mailman/listinfo/uclinux-dev> > <http://mailman.uclinux.org/__mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/mailman/listinfo/uclinux-dev>> > > > This message was resent by > uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>>> > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>. > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>.>__org > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>>>> > > > To unsubscribe see: > > > > http://mailman.uclinux.org/____mailman/options/uclinux-dev > <http://mailman.uclinux.org/__mailman/options/uclinux-dev> > <http://mailman.uclinux.org/__mailman/options/uclinux-dev > <http://mailman.uclinux.org/mailman/options/uclinux-dev>> > > > > > > > > > > ___________________________________________________ > > > uClinux-dev mailing list > > > uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>>> <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>. <mailto:uClinux-dev@uclinux > <mailto:uClinux-dev@uclinux>.>__org <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>>>> > > > > http://mailman.uclinux.org/____mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/__mailman/listinfo/uclinux-dev> > <http://mailman.uclinux.org/__mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/mailman/listinfo/uclinux-dev>> > > > This message was resent by > uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>>> > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>. > <mailto:uclinux-dev@uclinux <mailto:uclinux-dev@uclinux>.>__org > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>>>> > > > To unsubscribe see: > > > > http://mailman.uclinux.org/____mailman/options/uclinux-dev > <http://mailman.uclinux.org/__mailman/options/uclinux-dev> > <http://mailman.uclinux.org/__mailman/options/uclinux-dev > <http://mailman.uclinux.org/mailman/options/uclinux-dev>> > > > > > > > > > > > > > > > > _________________________________________________ > > > uClinux-dev mailing list > > > uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>>> > > > > http://mailman.uclinux.org/__mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/mailman/listinfo/uclinux-dev> > > > This message was resent by > uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>>> > > > To unsubscribe see: > > > > http://mailman.uclinux.org/__mailman/options/uclinux-dev > <http://mailman.uclinux.org/mailman/options/uclinux-dev> > > > > > > > > > _________________________________________________ > > > uClinux-dev mailing list > > > uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>>> > > > > http://mailman.uclinux.org/__mailman/listinfo/uclinux-dev > <http://mailman.uclinux.org/mailman/listinfo/uclinux-dev> > > > This message was resent by > uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org> > <mailto:uclinux-dev@uclinux.org <mailto:uclinux-dev@uclinux.org>>> > > > To unsubscribe see: > > > > http://mailman.uclinux.org/__mailman/options/uclinux-dev > <http://mailman.uclinux.org/mailman/options/uclinux-dev> > > > > > > > > > > > > > > > _______________________________________________ > > > uClinux-dev mailing list > > > uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>> > > > > http://mailman.uclinux.org/mailman/listinfo/uclinux-dev > > > This message was resent by uclinux-dev@uclinux.org > <mailto:uclinux-dev@uclinux.org> <mailto:uclinux-dev@uclinux.org > <mailto:uclinux-dev@uclinux.org>> > > > To unsubscribe see: > > > http://mailman.uclinux.org/mailman/options/uclinux-dev > > > > > > > _______________________________________________ > > uClinux-dev mailing list > > uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org> <mailto:uClinux-dev@uclinux.org > <mailto:uClinux-dev@uclinux.org>> > > http://mailman.uclinux.org/mailman/listinfo/uclinux-dev > > This message was resent by uclinux-dev@uclinux.org > <mailto:uclinux-dev@uclinux.org> <mailto:uclinux-dev@uclinux.org > <mailto:uclinux-dev@uclinux.org>> > > To unsubscribe see: > > http://mailman.uclinux.org/mailman/options/uclinux-dev > > > > > > > > > > > > _______________________________________________ > > uClinux-dev mailing list > > uClinux-dev@uclinux.org <mailto:uClinux-dev@uclinux.org> > > http://mailman.uclinux.org/mailman/listinfo/uclinux-dev > > This message was resent by uclinux-dev@uclinux.org > <mailto:uclinux-dev@uclinux.org> > > To unsubscribe see: > > http://mailman.uclinux.org/mailman/options/uclinux-dev > > > > _______________________________________________ > uClinux-dev mailing list > uClinux-dev@uclinux.org <mailto:uClinux-dev@uclinux.org> > http://mailman.uclinux.org/mailman/listinfo/uclinux-dev > This message was resent by uclinux-dev@uclinux.org > <mailto:uclinux-dev@uclinux.org> > To unsubscribe see: > http://mailman.uclinux.org/mailman/options/uclinux-dev > > > > > > > _______________________________________________ > uClinux-dev mailing list > uClinux-dev@uclinux.org > http://mailman.uclinux.org/mailman/listinfo/uclinux-dev > This message was resent by uclinux-dev@uclinux.org > To unsubscribe see: > http://mailman.uclinux.org/mailman/options/uclinux-dev > _______________________________________________ uClinux-dev mailing list uClinux-dev@uclinux.org http://mailman.uclinux.org/mailman/listinfo/uclinux-dev This message was resent by uclinux-dev@uclinux.org To unsubscribe see: http://mailman.uclinux.org/mailman/options/uclinux-dev
