-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi Paul,
You have ipv6 enabled (#do-ipv6: yes at the default) and you have tcp disabled. You should consider do-tcp: yes since the DNS occasionally needs to use TCP, but that is not the cause of your socket errors. Best regards, Wouter On 09/10/14 15:14, Paul Stewart wrote: > Hi Wouter and thanks again for the prompt responses.... > > Here is the configuration to hopefully answer your questions. I > read through the performance documentation and made several > adjustments so perhaps one of those changes were done in error. > > Much appreciated, > > Paul > > # # See unbound.conf(5) man page. # # this is a comment. > > #Use this to include other text into the file. #include: > "otherfile.conf" > > # The server clause sets the main parameters. server: # whitespace > is not necessary, but looks cleaner. > > # verbosity number, 0 is least verbose. 1 is default. verbosity: 1 > > # print statistics to the log (for every thread) every N seconds. # > Set to "" or 0 to disable. Default is disabled. # Needed for munin > plugin statistics-interval: 60 > > # enable cumulative statistics, without clearing them after > printing. # Needed for munin plugin statistics-cumulative: yes > > # enable extended statistics (query types, answer codes, status) # > printed from unbound-control. default off, because of speed. # > Needed for munin plugin extended-statistics: yes > > # number of threads to create. 1 disables threading. num-threads: > 4 > > # specify the interfaces to answer queries from by ip-address. # > The default is to listen to localhost (127.0.0.1 and ::1). # > specify 0.0.0.0 and ::0 to bind to all available interfaces. # > specify every interface on a new 'interface:' labelled line. # The > listen interfaces are not changed on reload, only on restart. > interface: xx.xx.xx.90 # interface: ::0 # interface: 192.0.2.153 # > interface: 192.0.2.154 # interface: 2001:DB8::5 # # for dns over > tls and raw dns over port 80 # interface: 0.0.0.0@443 # interface: > ::0@443 # interface: 0.0.0.0@80 # interface: ::0@80 > > # enable this feature to copy the source address of queries to > reply. # Socket options are not supported on all platforms. > experimental. # interface-automatic: yes # # NOTE: Enable this > option when specifying interface 0.0.0.0 or ::0 # NOTE: Disabled > per Fedora policy not to listen to * on default install # NOTE: If > deploying on non-default port, eg 80/443, this needs to be > disabled interface-automatic: no > > # port to answer queries from # port: 53 > > # specify the interfaces to send outgoing queries to authoritative > # server from by ip-address. If none, the default (all) interface # > is used. Specify every interface on a 'outgoing-interface:' line. # > outgoing-interface: 192.0.2.153 # outgoing-interface: 2001:DB8::5 # > outgoing-interface: 2001:DB8::6 > > # number of ports to allocate per thread, determines the size of > the # port range that can be open simultaneously. outgoing-range: > 200 > > # permit unbound to use this port number or port range for # making > outgoing queries, using an outgoing interface. # > outgoing-port-permit: 32768 > > # deny unbound the use this of port number or port range for # > making outgoing queries, using an outgoing interface. # Use this to > make sure unbound does not grab a UDP port that some # other server > on this computer needs. The default is to avoid # IANA-assigned > port numbers. # outgoing-port-avoid: "3200-3208" > > # number of outgoing simultaneous tcp buffers to hold per thread. # > outgoing-num-tcp: 10 > > # number of incoming simultaneous tcp buffers to hold per thread. # > incoming-num-tcp: 10 > > # buffer size for UDP port 53 incoming (SO_RCVBUF socket option). # > 0 is system default. Use 4m to catch query spikes for busy > servers. so-rcvbuf: 8m > > # buffer size for UDP port 53 outgoing (SO_SNDBUF socket option). # > 0 is system default. Use 4m to handle spikes on very busy > servers. so-sndbuf: 8m > > # EDNS reassembly buffer to advertise to UDP peers (the actual > buffer # is set with msg-buffer-size). 1480 can solve > fragmentation (timeouts). # edns-buffer-size: 4096 > > # buffer size for handling DNS data. No messages larger than this # > size can be sent or received, by UDP or TCP. In bytes. # > msg-buffer-size: 65552 > > # the amount of memory to use for the message cache. # plain value > in bytes or you can append k, m or G. default is "4Mb". # > msg-cache-size: 4m > > # the number of slabs to use for the message cache. # the number of > slabs must be a power of 2. # more slabs reduce lock contention, > but fragment memory usage. msg-cache-slabs: 4 > > # the number of queries that a thread gets to service. > num-queries-per-thread: 100 > > # if very busy, 50% queries run to completion, 50% get timeout in > msec # jostle-timeout: 200 > > # the amount of memory to use for the RRset cache. # plain value in > bytes or you can append k, m or G. default is "4Mb". > rrset-cache-size: 2G > > # the number of slabs to use for the RRset cache. # the number of > slabs must be a power of 2. # more slabs reduce lock contention, > but fragment memory usage. rrset-cache-slabs: 4 > > # the time to live (TTL) value lower bound, in seconds. Default 0. > # If more than an hour could easily give trouble due to stale > data. # cache-min-ttl: 0 > > # the time to live (TTL) value cap for RRsets and messages in the # > cache. Items are not cached for longer. In seconds. # > cache-max-ttl: 86400 > > # the time to live (TTL) value for cached roundtrip times, > lameness # and EDNS version information for hosts. In seconds. # > infra-host-ttl: 900 > > # the number of slabs to use for the Infrastructure cache. # the > number of slabs must be a power of 2. # more slabs reduce lock > contention, but fragment memory usage. infra-cache-slabs: 4 > > # the maximum number of hosts that are cached (roundtrip, EDNS, > lame). # infra-cache-numhosts: 10000 > > # Enable IPv4, "yes" or "no". do-ip4: yes > > # Enable IPv6, "yes" or "no". # do-ip6: yes > > # Enable UDP, "yes" or "no". # NOTE: if setting up an unbound on > tls443 for public use, you might want to # disable UDP to avoid > being used in DNS amplification attacks. do-udp: yes > > # Enable TCP, "yes" or "no". do-tcp: no > > # upstream connections use TCP only (and no UDP), "yes" or "no" # > useful for tunneling scenarios, default no. # tcp-upstream: no > > # Detach from the terminal, run in background, "yes" or "no". # > do-daemonize: yes > > # control which clients are allowed to make (recursive) queries # > to this server. Specify classless netblocks with /size and action. > # By default everything is refused, except for localhost. # Choose > deny (drop message), refuse (polite error reply), # allow > (recursive ok), allow_snoop (recursive and nonrecursive ok) # > access-control: 0.0.0.0/0 refuse access-control: xxx.xxx.xx.0/19 > allow access-control: xx.xxx.xx.0/19 allow access-control: > xx.xxx.xx.0/18 allow access-control: xx.xxx.0.0/18 allow > access-control: xxx.xxx.xxx.0/17 allow # access-control: ::0/0 > refuse # access-control: ::1 allow # access-control: > ::ffff:127.0.0.1 allow > > # if given, a chroot(2) is done to the given directory. # i.e. you > can chroot to the working directory, for example, # for extra > security, but make sure all files are in that directory. # # If > chroot is enabled, you should pass the configfile (from the # > commandline) as a full path from the original root. After the # > chroot has been performed the now defunct portion of the config # > file path is removed to be able to reread the config after a > reload. # # All other file paths (working dir, logfile, roothints, > and # key files) can be specified in several ways: # o as an > absolute path relative to the new root. # o as a relative path to > the working directory. # o as an absolute path relative to the > original root. # In the last case the path is adjusted to remove > the unused portion. # # The pid file can be absolute and outside of > the chroot, it is # written just prior to performing the chroot and > dropping permissions. # # Additionally, unbound may need to access > /dev/random (for entropy). # How to do this is specific to your > OS. # # If you give "" no chroot is performed. The path must not > end in a /. # chroot: "/var/lib/unbound" chroot: "" > > # if given, user privileges are dropped (after binding port), # and > the given username is assumed. Default is user "unbound". # If you > give "" no privileges are dropped. username: "unbound" > > # the working directory. The relative files in this config are # > relative to this directory. If you give "" the working directory # > is not changed. directory: "/etc/unbound" > > # the log file, "" means log to stderr. # Use of this option sets > use-syslog to "no". # logfile: "" > > # Log to syslog(3) if yes. The log facility LOG_DAEMON is used to # > log to, with identity "unbound". If yes, it overrides the logfile. > # use-syslog: yes > > # print UTC timestamp in ascii to logfile, default is epoch in > seconds. log-time-ascii: yes > > # the pid file. Can be an absolute path outside of chroot/work > dir. pidfile: "/var/run/unbound/unbound.pid" > > # file to read root hints from. # get one from > ftp://FTP.INTERNIC.NET/domain/named.cache # root-hints: "" > > # enable to not answer id.server and hostname.bind queries. # > hide-identity: no > > # enable to not answer version.server and version.bind queries. # > hide-version: no > > # the identity to report. Leave "" or default to return hostname. # > identity: "" > > # the version to report. Leave "" or default to return package > version. # version: "" > > # the target fetch policy. # series of integers describing the > policy per dependency depth. # The number of values in the list > determines the maximum dependency # depth the recursor will pursue > before giving up. Each integer means: # -1 : fetch all targets > opportunistically, # 0: fetch on demand, # positive value: fetch > that many targets opportunistically. # Enclose the list of numbers > between quotes (""). # target-fetch-policy: "3 2 1 0 0" > > # Harden against very small EDNS buffer sizes. # > harden-short-bufsize: no > > # Harden against unseemly large queries. # harden-large-queries: > no > > # Harden against out of zone rrsets, to avoid spoofing attempts. > harden-glue: yes > > # Harden against receiving dnssec-stripped data. If you turn it # > off, failing to validate dnskey data for a trustanchor will # > trigger insecure mode for that zone (like without a trustanchor). # > Default on, which insists on dnssec data for trust-anchored zones. > harden-dnssec-stripped: yes > > # Harden against queries that fall under dnssec-signed nxdomain > names. harden-below-nxdomain: yes > > # Harden the referral path by performing additional queries for # > infrastructure data. Validates the replies (if possible). # > Default off, because the lookups burden the server. Experimental # > implementation of > draft-wijngaards-dnsext-resolver-side-mitigation. > harden-referral-path: yes > > # Use 0x20-encoded random bits in the query to foil spoof > attempts. # This feature is an experimental implementation of draft > dns-0x20. # (this now fails on all GoDaddy customer domains, so > disabled) use-caps-for-id: no > > # Enforce privacy of these addresses. Strips them away from > answers. # It may cause DNSSEC validation to additionally mark it > as bogus. # Protects against 'DNS Rebinding' (uses browser as > network proxy). # Only 'private-domain' and 'local-data' names are > allowed to have # these private addresses. No default. # > private-address: 10.0.0.0/8 # private-address: 172.16.0.0/12 # > private-address: 192.168.0.0/16 # private-address: 192.254.0.0/16 # > private-address: fd00::/8 # private-address: fe80::/10 > > # Allow the domain (and its subdomains) to contain private > addresses. # local-data statements are allowed to contain private > addresses too. # private-domain: "example.com" > > # If nonzero, unwanted replies are not only reported in > statistics, # but also a running total is kept per thread. If it > reaches the # threshold, a warning is printed and a defensive > action is taken, # the cache is cleared to flush potential poison > out of it. # A suggested value is 10000000, the default is 0 > (turned off). unwanted-reply-threshold: 10000000 > > # Do not query the following addresses. No DNS queries are sent > there. # List one address per entry. List classless netblocks with > /size, # do-not-query-address: 127.0.0.1/8 # do-not-query-address: > ::1 > > # if yes, the above default do-not-query-address entries are > present. # if no, localhost can be queried (for testing and > debugging). # do-not-query-localhost: yes > > # if yes, perform prefetching of almost expired message cache > entries. prefetch: yes > > # if yes, perform key lookups adjacent to normal lookups. > prefetch-key: yes > > # if yes, Unbound rotates RRSet order in response. > rrset-roundrobin: yes > > # if yes, Unbound doesn't insert authority/additional sections # > into response messages when those sections are not required. > minimal-responses: yes > > # module configuration of the server. A string with identifiers # > separated by spaces. "iterator" or "validator iterator" # > module-config: "validator iterator" > > # File with DLV trusted keys. Same format as trust-anchor-file. # > There can be only one DLV configured, it is trusted from root > down. # Downloaded from > https://secure.isc.org/ops/dlv/dlv.isc.org.key dlv-anchor-file: > "/etc/unbound/dlv.isc.org.key" > > # File with trusted keys for validation. Specify more than one > file # with several entries, one file per entry. # Zone file > format, with DS and DNSKEY entries. # trust-anchor-file: "" > > # File with trusted keys, kept uptodate using RFC5011 probes, # > initial file like trust-anchor-file, then it stores metadata. # Use > several entries, one per domain name, to track multiple zones. # > auto-trust-anchor-file: "" > > # Trusted key for validation. DS or DNSKEY. specify the RR on a # > single line, surrounded by "". TTL is ignored. class is IN > default. # (These examples are from August 2007 and may not be > valid anymore). # trust-anchor: "nlnetlabs.nl. DNSKEY 257 3 5 > AQPzzTWMz8qSWIQlfRnPckx2BiVmkVN6LPupO3mbz7FhLSnm26n6iG9N > Lby97Ji453aWZY3M5/xJBSOS2vWtco2t8C0+xeO1bc/d6ZTy32DHchpW 6rDH1vp8 > 6Ll+ha0tmwyy9QP7y2bVw5zSbFCrefk8qCUBgfHm9bHzMG1U BYtEIQ==" # > trust-anchor: "jelte.nlnetlabs.nl. DS 42860 5 1 > 14D739EB566D2B1A5E216A0BA4D17FA9B038BE4A" > > # File with trusted keys for validation. Specify more than one > file # with several entries, one file per entry. Like > trust-anchor-file # but has a different file format. Format is > BIND-9 style format, # the trusted-keys { name flag proto algo > "key"; }; clauses are read. # trusted-keys-file: "" # # > trusted-keys-file: /etc/unbound/rootkey.bind trusted-keys-file: > /etc/unbound/keys.d/*.key auto-trust-anchor-file: > "/var/lib/unbound/root.key" > > # Ignore chain of trust. Domain is treated as insecure. # > domain-insecure: "example.com" > > # Override the date for validation with a specific fixed date. # Do > not set this unless you are debugging signature inception # and > expiration. "" or "0" turns the feature off. # val-override-date: > "" > > # The time to live for bogus data, rrsets and messages. This > avoids # some of the revalidation, until the time interval expires. > in secs. # val-bogus-ttl: 60 > > # The signature inception and expiration dates are allowed to be > off # by 10% of the lifetime of the signature from our local > clock. # This leeway is capped with a minimum and a maximum. In > seconds. # val-sig-skew-min: 3600 # val-sig-skew-max: 86400 > > # Should additional section of secure message also be kept clean > of # unsecure data. Useful to shield the users of this validator > from # potential bogus data in the additional section. All unsigned > data # in the additional section is removed from secure messages. > val-clean-additional: yes > > # Turn permissive mode on to permit bogus messages. Thus, messages > # for which security checks failed will be returned to clients, # > instead of SERVFAIL. It still performs the security checks, which # > result in interesting log files and possibly the AD bit in # > replies if the message is found secure. The default is off. # NOTE: > TURNING THIS ON DISABLES ALL DNSSEC SECURITY val-permissive-mode: > no > > # Have the validator log failed validations for your diagnosis. # > 0: off. 1: A line per failed user query. 2: With reason and bad > IP. val-log-level: 1 > > # It is possible to configure NSEC3 maximum iteration counts per # > keysize. Keep this table very short, as linear search is done. # A > message with an NSEC3 with larger count is marked insecure. # List > in ascending order the keysize and count values. # > val-nsec3-keysize-iterations: "1024 150 2048 500 4096 2500" > > # instruct the auto-trust-anchor-file probing to add anchors after > ttl. # add-holddown: 2592000 # 30 days > > # instruct the auto-trust-anchor-file probing to del anchors after > ttl. # del-holddown: 2592000 # 30 days > > # auto-trust-anchor-file probing removes missing anchors after > ttl. # If the value 0 is given, missing anchors are not removed. # > keep-missing: 31622400 # 366 days > > # the amount of memory to use for the key cache. # plain value in > bytes or you can append k, m or G. default is "4Mb". # > key-cache-size: 4m > > # the number of slabs to use for the key cache. # the number of > slabs must be a power of 2. # more slabs reduce lock contention, > but fragment memory usage. key-cache-slabs: 4 > > # the amount of memory to use for the negative cache (used for > DLV). # plain value in bytes or you can append k, m or G. default > is "1Mb". # neg-cache-size: 1m > > # a number of locally served zones can be configured. # > local-zone: <zone> <type> # local-data: "<resource record > string>" # o deny serves local data (if any), else, drops queries. > # o refuse serves local data (if any), else, replies with error. # > o static serves local data, else, nxdomain or nodata answer. # o > transparent serves local data, but resolves normally for other > names # o redirect serves the zone data for any subdomain in the > zone. # o nodefault can be used to normally resolve AS112 zones. # > o typetransparent resolves normally for other types and other > names # # defaults are localhost address, reverse for 127.0.0.1 and > ::1 # and nxdomain for AS112 zones. If you configure one of these > zones # the default content is omitted, or you can omit it with > 'nodefault'. # # If you configure local-data without specifying > local-zone, by # default a transparent local-zone is created for > the data. # # You can add locally served data with # local-zone: > "local." static # local-data: "mycomputer.local. IN A 192.0.2.51" # > local-data: 'mytext.local TXT "content of text record"' # # You can > override certain queries with # local-data: "adserver.example.com A > 127.0.0.1" # # You can redirect a domain to a fixed address with # > (this makes example.com, www.example.com, etc, all go to > 192.0.2.3) # local-zone: "example.com" redirect # local-data: > "example.com A 192.0.2.3" # # Shorthand to make PTR records, "IPv4 > name" or "IPv6 name". # You can also add PTR records using > local-data directly, but then # you need to do the reverse notation > yourself. # local-data-ptr: "192.0.2.3 www.example.com" > > include: /etc/unbound/local.d/*.conf > > # service clients over SSL (on the TCP sockets), with plain DNS > inside # the SSL stream. Give the certificate to use and private > key. # default is "" (disabled). requires restart to take effect. > # ssl-service-key: "/etc/unbound/unbound_server.key" # > ssl-service-pem: "/etc/unbound/unbound_server.pem" # ssl-port: 443 > > # request upstream over SSL (with plain DNS inside the SSL > stream). # Default is no. Can be turned on and off with > unbound-control. # ssl-upstream: no > > ## Python config section. To enable: ## o use --with-pythonmodule > to configure before compiling. ## o list python in the > module-config string (above) to enable. ## o and give a > python-script to run. #python: # # Script file to load # # > python-script: "/etc/unbound/ubmodule-tst.py" > > > # Remote control config section. remote-control: # Enable remote > control with unbound-control(8) here. # set up the keys and > certificates with unbound-control-setup. # Note: required for > unbound-munin package control-enable: yes > > # what interfaces are listened to for remote control. # give > 0.0.0.0 and ::0 to listen to all interfaces. # control-interface: > 127.0.0.1 # control-interface: ::1 > > # port number for remote control operations. # control-port: 953 > > # unbound server key file. server-key-file: > "/etc/unbound/unbound_server.key" > > # unbound server certificate file. server-cert-file: > "/etc/unbound/unbound_server.pem" > > # unbound-control key file. control-key-file: > "/etc/unbound/unbound_control.key" > > # unbound-control certificate file. control-cert-file: > "/etc/unbound/unbound_control.pem" > > # Stub and Forward zones > > include: /etc/unbound/conf.d/*.conf > > # Stub zones. # Create entries like below, to make all queries for > 'example.com' and # 'example.org' go to the given list of > nameservers. list zero or more # nameservers by hostname or by > ipaddress. If you set stub-prime to yes, # the list is treated as > priming hints (default is no). # stub-zone: # name: "example.com" # > stub-addr: 192.0.2.68 # stub-prime: "no" # stub-zone: # name: > "example.org" # stub-host: ns.example.com. # You can now also > dynamically create and delete stub-zone's using # unbound-control > stub_add domain.com 1.2.3.4 5.6.7.8 # unbound-control stub_remove > domain.com 1.2.3.4 5.6.7.8 > > # Forward zones # Create entries like below, to make all queries > for 'example.com' and # 'example.org' go to the given list of > servers. These servers have to handle # recursion to other > nameservers. List zero or more nameservers by hostname # or by > ipaddress. Use an entry with name "." to forward all queries. # If > you enable forward-first, it attempts without the forward if it > fails. # forward-zone: # name: "example.com" # forward-addr: > 192.0.2.68 # forward-addr: 192.0.2.73@5355 # forward to port > 5355. # forward-first: no # forward-zone: # name: "example.org" # > forward-host: fwd.example.com # # You can now also dynamically > create and delete forward-zone's using # unbound-control > forward_add domain.com 1.2.3.4 5.6.7.8 # unbound-control > forward_remove domain.com 1.2.3.4 5.6.7.8 > > -----Original Message----- From: Unbound-users > [mailto:[email protected]] On Behalf Of W.C.A. > Wijngaards Sent: Thursday, October 09, 2014 7:54 AM To: > [email protected] Subject: Re: [Unbound-users] Can't Bind > Socket Error > > Hi Paul, > > Did you configure the interface or the outgoing-interface? In any > case, 0.0.0.0 or your IP giving permission denied once in a while > is bad. Something is wrong with your system somehow, and it is > intermittent. Are there port numbers that are not allowed by > system policy that you have enabled in unbound.conf (by default it > skips <1024 ports) ? > > Best regards, Wouter > > On 09/10/14 13:42, Paul Stewart wrote: >> Thank you for the response. There is only one interface >> configured in the CentOS and IPv6 is disabled (for now - it will >> be turned up shortly). > >> In the configuration of Unbound, I specified the IP address >> (there is only one) - should I perhaps change the IP to 0.0.0.0? >> It doesn't appear that the error in the log file is causing any >> serious issues .... > >> Cheers, Paul > > >>> >>> We just started migrating some of our customer base over to >>> Unbound. >>> >>> >>> >>> Server is VM instance (VmWare) with 8 Gig RAM, 4 vCPU's running >>> CentOS 7 (64 bit). Unbound version 1.4.20 via YUM package >>> install. > >> The socket bind this late is for queries to upstream authority >> servers, it is trying to bind one of the outgoing-interface IP >> addresses. If you configured it, one of those addresses is not >> actually served by your system (or the VM). Another option is >> that IPv6 is broken in the VM and binding the ipv6 fd to ::0 >> fails. > >> Best regards, Wouter > >>> We started noticing the following errors in the logs this >>> evening: >>> >>> >>> >>> Oct 8 19:48:51 dns2-pppoe unbound: [1110:0] error: can't bind >>> *socket*: Permission denied > > >> _______________________________________________ Unbound-users >> mailing list [email protected] >> http://unbound.nlnetlabs.nl/mailman/listinfo/unbound-users > > > _______________________________________________ Unbound-users > mailing list [email protected] > http://unbound.nlnetlabs.nl/mailman/listinfo/unbound-users > > > _______________________________________________ Unbound-users > mailing list [email protected] > http://unbound.nlnetlabs.nl/mailman/listinfo/unbound-users > -----BEGIN PGP SIGNATURE----- Version: GnuPG v1 iQIcBAEBAgAGBQJUNo5ZAAoJEJ9vHC1+BF+N5H4P/2j/c888Mivjw/021IgP69rz G95et9xIoOW+dxsuFfjfWpc8cvcS7yd096KQ49LCGNcl0bFHZ16+P0V0dqAjd3tT dKXrIlzIZs/CNFOSWjwNny+B0PZ5Zb55uTuomFNt6dEJhxMZERlbqjo0JEFX4/bO P99N4isr6EcOCr+uj23bajf23r7HYwYylFRdH18DtrR4plA0P3PjJmdFsfvHE1at xzSkg7NGQ3vOBn+LTRyupkR227S8iDcEqsp6wF0lOuzFzkFLQsazNhwGIT+oSgui SHXXh6H0Yres0vHg5L1k4l+LNNrDkbEUFqXd55Vs8MtEsgWY3eGZX3RS62Fq8/Uh XzYwF1DfAMpLpJBKBK4qQ2EA+YMJpOs5avvpDqU5YNb/RQ/+ziavm/jJFyD5xN5k WLTIBs0NaZbAGPl+IWoxPOiNNtez0MHrBElEH9GcKqLZfuV0BBBYE78sqG0v1NyA xd6KbKeVDjKNJ3NetLw4irfvSydEYmzvJTx5on+6C4JQc517ii/krqnNj2GEAVph I/7xSrvGzHQkLw6IUuNLP08SglC0IF3MIyyUhKgVHscEbQYsBBocORVyzTJzjSsl pJwBcKOBZyFQVSPAeUAJUgx8r49SoBt6zamBrS/u6m5yEBvecCVEfnd1SJoRWt7/ 9KPUvpHDCoEwVzbL8JqP =J56F -----END PGP SIGNATURE----- _______________________________________________ Unbound-users mailing list [email protected] http://unbound.nlnetlabs.nl/mailman/listinfo/unbound-users
