Hello Bill, You do not need to disable error msgs to build a standalone. I am not sure if you ever had to.
Kind regards, Panos -- On Tue, 1 Feb 2022 at 18:46, William Prothero via use-livecode < use-livecode@lists.runrev.com> wrote: > Regarding this, I don’t recall seeing a reply to my query about whether > you still need to disable error messages when building a standalone. > Hopefully this has been fixed, but … > > Best, > Bill > > William A. Prothero, PhD > Prof Emeritus, Dept of Earth Science > University of California, Santa Barbara > > > On Feb 1, 2022, at 6:59 AM, matthias rebbe via use-livecode < > use-livecode@lists.runrev.com> wrote: > > > > Mark, > > > > where are you saving the standalone to? > > Any chance that the target folder is on iCloud drive. E.g. Desktop or > Documents folder? > > > > I had similar problems in the past when i built the standalone directly > on the Desktop or Documents folder which were both synchronized with iCloud > Drive. I just cannot remember the correct error message. Sometimes the > build process was successful and sometimes it was aborted. > > I could solve this to select a target folder outside of iCloud Drive. > > Btw. building the standalone in a Dropbox folder works w/o problems. > > > > Matthias > > > >> Am 01.02.2022 um 11:47 schrieb Mark Smith via use-livecode < > use-livecode@lists.runrev.com>: > >> > >> Hi Panos, > >> > >> I did not change anything between attempts, just one right after the > other. I guess I was observing this in RC2 and just persisted and it seemed > to work on the 2nd or 3rd attempt. For good measure I just took the same > stack and was able to build and install two more times without incident so > it’s definitely not a repeatable problem and as yet I have no formula or > hypothesis as to what might be causing it. I’ll keep an eye on it and log > any similar problems I run across. > >> > >> Mark > >> > >> > >>>> On Feb 1, 2022, at 10:23 AM, panagiotis m via use-livecode < > use-livecode@lists.runrev.com> wrote: > >>> > >>> Hello Mark, > >>> > >>> I have not seen this before. Did anything change in your stack (used a > >>> different provisioning profile or changed anything in the iOS > settings) or > >>> in the iOS device until the successful 3rd attempt? > >>> > >>> I cannot remember of anything that we changed in the 9.6.6 release > cycle > >>> that could have caused this behavior. > >>> > >>> Kind regards, > >>> Panos > >>> > >>> On Tue, 1 Feb 2022 at 12:14, Mark Smith via use-livecode < > >>> use-livecode@lists.runrev.com> wrote: > >>> > >>>> I just wanted to flag this issue. I am currently using the new release > >>>> version of 9.6.6 although I did have similar problems with RC2 as > well. > >>>> This morning I took a stack I had previously built and successfully > >>>> installed (using Development/Test Target -> iPhone) and tried > installing > >>>> it. The first time the app went through what appeared to be all the > build > >>>> steps but did not install the app. The 2nd time it went through all > of the > >>>> steps and then reported “Unknown Error” and the 3rd time it built and > >>>> installed the app correctly. I’ve not noticed behaviour like this in > >>>> previous versions. At the moment I have no hypothesis about what > might be > >>>> going on. > >>>> > >>>> Mark > >>>> > >>>> > >>>> _______________________________________________ > >>>> use-livecode mailing list > >>>> use-livecode@lists.runrev.com > >>>> Please visit this url to subscribe, unsubscribe and manage your > >>>> subscription preferences: > >>>> http://lists.runrev.com/mailman/listinfo/use-livecode > >>>> > >>> _______________________________________________ > >>> use-livecode mailing list > >>> use-livecode@lists.runrev.com > >>> Please visit this url to subscribe, unsubscribe and manage your > subscription preferences: > >>> http://lists.runrev.com/mailman/listinfo/use-livecode > >> > >> > >> _______________________________________________ > >> use-livecode mailing list > >> use-livecode@lists.runrev.com > >> Please visit this url to subscribe, unsubscribe and manage your > subscription preferences: > >> http://lists.runrev.com/mailman/listinfo/use-livecode > > > > > > _______________________________________________ > > use-livecode mailing list > > use-livecode@lists.runrev.com > > Please visit this url to subscribe, unsubscribe and manage your > subscription preferences: > > http://lists.runrev.com/mailman/listinfo/use-livecode > > > _______________________________________________ > use-livecode mailing list > use-livecode@lists.runrev.com > Please visit this url to subscribe, unsubscribe and manage your > subscription preferences: > http://lists.runrev.com/mailman/listinfo/use-livecode > _______________________________________________ use-livecode mailing list use-livecode@lists.runrev.com Please visit this url to subscribe, unsubscribe and manage your subscription preferences: http://lists.runrev.com/mailman/listinfo/use-livecode
