Jean, I'm getting a whole bunch of errors if i try your method! I don't why i'm the only one who's encountering all this type of errors ..
On Tue, Jul 16, 2013 at 6:07 PM, Jean-Marc Spaggiari <[email protected]> wrote: > Sure! > > Here is the /etc/hosts file from my "hbasetest" server where I run > PerformanceEvaluation tests on a standalone HBase: > jmspaggi@hbasetest:~$ cat /etc/hosts > 127.0.0.1 localhost > 192.168.23.105 hbasetest > > # The following lines are desirable for IPv6 capable hosts > ::1 localhost ip6-localhost ip6-loopback > fe00::0 ip6-localnet > ff00::0 ip6-mcastprefix > ff02::1 ip6-allnodes > ff02::2 ip6-allrouters > ff02::3 ip6-allhosts > > > As you can see, keep it simple ;) > > 192.168.23.105 is the local IP; > root@hbasetest:/home/jmspaggi# ifconfig eth0 > eth0 Link encap:Ethernet HWaddr 90:2b:34:a0:16:d8 > inet adr:192.168.23.105 Bcast:192.168.23.255 > Masque:255.255.255.0 > adr inet6: fe80::922b:34ff:fea0:16d8/64 Scope:Lien > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:456 errors:0 dropped:0 overruns:0 frame:0 > TX packets:237 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 lg file transmission:1000 > RX bytes:43079 (42.0 KiB) TX bytes:32650 (31.8 KiB) > Interruption:40 Adresse de base:0xa000 > > And I do everything using "hbasetest" name. > > You can ignore the IPV6 lines in the hosts file. > > JM > > 2013/7/16 Pavan Sudheendra <[email protected]> > >> Jean, can you post an example HBase stand-alone /etc/hosts file? >> It would be very helpful. >> >> On Tue, Jul 16, 2013 at 5:43 PM, Jean-Marc Spaggiari >> <[email protected]> wrote: >> > I will say it should be your host name. Not the IP nor "localhost". >> > >> > 2013/7/16 Rohit Kelkar <[email protected]> >> > >> >> Depends on what your /etc/hosts file says >> >> >> >> On Tuesday, July 16, 2013, Pavan Sudheendra wrote: >> >> >> >> > Ah. The value of quorun should be localhost or my ip address? >> >> > >> >> > On Tue, Jul 16, 2013 at 5:32 PM, Rohit Kelkar <[email protected]> >> >> > wrote: >> >> > > I suggested that because you were able to use the shell but not the >> >> > client >> >> > > code. >> >> > > >> >> > > - R >> >> > > >> >> > > On Tuesday, July 16, 2013, Pavan Sudheendra wrote: >> >> > > >> >> > >> Yes Jean, It is working fine. >> >> > >> @Rohit, i thought in the standalone mode it is not required. >> >> > >> >> >> > >> On Tue, Jul 16, 2013 at 5:25 PM, Rohit Kelkar < >> [email protected]> >> >> > >> wrote: >> >> > >> > In your client code can you try explicitly setting values of >> >> > >> > hbase.zookeeper.quorum >> >> > >> > >> >> > >> > - R >> >> > >> > >> >> > >> > On Tuesday, July 16, 2013, Jean-Marc Spaggiari wrote: >> >> > >> > >> >> > >> >> Hi Pavan, >> >> > >> >> >> >> > >> >> You should try to avoid localhost. Try to prefers your host >> name. >> >> Is >> >> > >> >> http://ubuntu:60010/master-status?filter=all< >> >> > >> >> http://localhost:60010/master-status?filter=all>working >> >> > >> >> fine? >> >> > >> >> >> >> > >> >> JM >> >> > >> >> >> >> > >> >> 2013/7/16 Pavan Sudheendra <[email protected]> >> >> > >> >> >> >> > >> >> > Hi all, >> >> > >> >> > I further went to >> >> http://localhost:60010/master-status?filter=alland >> >> > >> >> > checked that: >> >> > >> >> > [{"statustimems":-1,"status":"Waiting for a >> >> > >> >> > call","starttimems":1373948304755,"description":"REPL IPC >> Server >> >> > >> >> > handler 2 on >> >> > >> >> > >> >> > >> >> >> >> > >> >> >> > >> >> >> 38039","state":"WAITING","statetimems":-1},{"statustimems":-1,"status":"Waiting >> >> > >> >> > for a call","starttimems":1373948304755,"description":"REPL >> IPC >> >> > Server >> >> > >> >> > handler 1 on >> >> > >> >> > >> >> > >> >> >> >> > >> >> >> > >> >> >> 38039","state":"WAITING","statetimems":-1},{"statustimems":-1,"status":"Waiting >> >> > >> >> > for a call","starttimems":1373948304755,"description":"REPL >> IPC >> >> > Server >> >> > >> >> > handler 0 on 38039","state":"WAITING","statetimems":-1}, >> >> > >> >> > >> >> > >> >> > all the rpc calls gets stuck on waiting.. and my master it >> says >> >> > active >> >> > >> >> > on the tasks page for a while and dissapears. Any help much >> >> > >> >> > appreciated. >> >> > >> >> > >> >> > >> >> > On Tue, Jul 16, 2013 at 8:54 AM, Pavan Sudheendra < >> >> > >> [email protected]> >> >> > >> >> > wrote: >> >> > >> >> > > @Kim how is that possible? I'm using the stable release. >> >> > >> >> > > >> >> > >> >> > > On Tue, Jul 16, 2013 at 8:37 AM, Pavan Sudheendra < >> >> > >> [email protected] >> >> > >> >> > >> >> > >> >> > wrote: >> >> > >> >> > >> @Jean, Nope, it didn't work. I even re-installed hbase. >> >> > >> >> > >> >> >> > >> >> > >> Has anyone worked with the Hbase-The definitive guide >> examples >> >> > with >> >> > >> >> > >> standalone mode? >> >> > >> >> > >> >> >> > >> >> > >> On Mon, Jul 15, 2013 at 10:06 PM, Kim Chew < >> >> [email protected]> >> >> > >> >> wrote: >> >> > >> >> > >>> Another thing is, >> >> > >> >> > >>> >> >> > >> >> > >>> 2013-07-15 05:15:58,764 WARN org.apache.hadoop.ipc. >> >> > >> >> > >>> HBaseServer: >> >> > >> >> > >>> Incorrect header or version mismatch from 127.0.0.1:46149 >> got >> >> > >> >> vers-- >> >> > Regards- >> >> > Pavan >> >> > >> >> >> >> >> >> -- >> Regards- >> Pavan >> -- Regards- Pavan
