Hi Jayapal, eth1 seems present (lspci and virsh comfirmed), but not started inside VPC's VR - (VR used for Shared Network is fine)... I could confirm by virsh that is is plugged inside appropriate bridge breth1-500 (check management logs...)
management log while createing new VPC (VR) - http://pastebin.com/s77nu5Ei The public IP is there, so command is fine for creating it I guess... VR's /var/log/cloud.log after rebooting VR from CS GUI Tue May 27 22:46:58 UTC 2014 Executing cloud-early-config Tue May 27 22:46:58 UTC 2014 Detected that we are running inside kvm guest Tue May 27 22:46:59 UTC 2014 Patching cloud service Tue May 27 22:47:00 UTC 2014 Updating log4j-cloud.xml Tue May 27 22:47:00 UTC 2014 Setting up VPC virtual router system vm Tue May 27 22:47:00 UTC 2014 checking that eth0 has IP Tue May 27 22:47:00 UTC 2014 Setting up apache web server for VPC Tue May 27 22:47:00 UTC 2014 Enable service dnsmasq = 1 Tue May 27 22:47:00 UTC 2014 Enable service haproxy = 1 Tue May 27 22:47:00 UTC 2014 Processors = 1 Enable service = 0 Tue May 27 22:47:00 UTC 2014 Enable service cloud = 0 Tue May 27 22:47:00 UTC 2014 cloud: disable rp_filter Tue May 27 22:47:00 UTC 2014 disable rpfilter Tue May 27 22:47:00 UTC 2014 cloud: enable_fwding = 1 Tue May 27 22:47:00 UTC 2014 enable_fwding = 1 ifconfig (no eth1 shown) eth0 Link encap:Ethernet HWaddr 0e:00:a9:fe:03:5c inet addr:169.254.3.92 Bcast:169.254.255.255 Mask:255.255.0.0 eth2 Link encap:Ethernet HWaddr 02:00:7d:92:00:10 inet addr:10.0.1.1 Bcast:10.0.1.255 Mask:255.255.255.0 eth3 Link encap:Ethernet HWaddr 02:00:78:e9:00:05 inet addr:10.0.3.1 Bcast:10.0.3.255 Mask:255.255.255.0 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 cat /etc/network/interfaces auto lo eth0 iface lo inet loopback iface eth0 inet static address 169.254.3.92 netmask 255.255.0.0 lspci - shows 4 ehternet addapters ethtool eth1 = no link detected virsh - confirmed that eth1 is plugged to correct bridge (breth1-500) as indicated by management logs, and shows good MAC address as shown in managemetn log on pastebin.. This is completely makeing VPCs unusable... :( Cheers On 27 May 2014 16:36, Jayapal Reddy Uradi <[email protected]>wrote: > Hi, > Can you please share management server and router logs in pastebin.com to > understand the issue ? > > Thanks, > Jayapal > > On 27-May-2014, at 6:21 PM, Andrija Panic <[email protected]> > wrote: > > > Hi, > > > > after the upgrade to ACS 4.3 (from 4.2.1) existing VRs for VPC lost their > > eth1 which is public NIC. VR got eth0(control nic) and eth2 and eth3 > (bith > > belonging to Tiers). From CS GUI, it is reported that the VR has eth1 > with > > Public network attached, but from inside (ssh to VR) there is no eth1 > with > > public IP... > > > > Even after destroying those VR, they are recreated again, but without > eth1. > > > > Anybody experienced same situtation ? > > > > Thanks, > > > > -- > > > > Andrija Panić > > -------------------------------------- > > -- Andrija Panić -------------------------------------- http://admintweets.com --------------------------------------
