Hi Boris, Thanks for your response. Yes I'm building a basic zone, just for starters.
--John O. Adams On 15 February 2017 at 16:32, Boris Stoyanov <boris.stoya...@shapeblue.com> wrote: > Hi John, > > Maybe I misunderstood, are you building advanced or basic zone? > > Thanks, > Boris Stoyanov > > boris.stoya...@shapeblue.com > www.shapeblue.com > @shapeblue > > > > > On Feb 15, 2017, at 12:34 PM, John Adams <adams.op...@gmail.com> wrote: > > Hi Boris, > > I think I'm actually using the Shared network offering. The VMs being > created are in the same same physical network subnet. Isolation is an > option but I'm not using that at this point. > > Thanks. > > > --John O. Adams > > On 15 February 2017 at 11:50, Boris Stoyanov <boris.stoya...@shapeblue.com > > wrote: > >> Hi John, >> >> In isolated networks VMs should be accessed only through the virtual >> router IP. >> >> To access the VM over ssh, you should go to network setting and enable a >> port on the Virtual Router IP. Then create a port forwarding rule from that >> enabled port to port 22 on the specific VM within that network. After that >> try to ssh the enabled port on the VR and you should end-up in the VM >> >> PS. In isolated networks you shouldn’t be able to ping the VM, all the >> traffic goes through the VR. >> >> Thanks, >> Boris Stoyanov >> >> >> >> boris.stoya...@shapeblue.com >> www.shapeblue.com >> 53 Chandos Place, Covent Garden, London WC2N 4HSUK >> @shapeblue >> >> >> >> > On Feb 15, 2017, at 8:37 AM, John Adams <adams.op...@gmail.com> wrote: >> > >> > Hi all, >> > >> > Still learning the ropes in a test environment here. Hitting a little >> snag >> > with networking here. The physical network has 2 VLANs. (192.168.10.0 >> and >> > 192.168.30.0) >> > >> > This is my current ACS testing environment: >> > >> > 1 management server (Ubuntu 14.04): 192.168.30.14 >> > 2 KVM Hosts (Ubuntu 14.04): 192.168.10.12 and 192.168.30.12 >> > >> > With that, I created 2 different zones, each with 1 pod and 1 cluster >> and 1 >> > host respectively. >> > >> > *The good:* >> > I can create VMs on either of the hosts. I'm able to ping the VMs and >> even >> > ssh into them only if I'm on the host or the management server or from >> the >> > ACS console itself (within the network). >> > >> > *The Issue:* >> > I can't ssh or even ping the VMs when in the same network outside the >> host >> > environment. What could be the problem? >> > >> > A. Management Server network config is as below: >> > ------------------------- >> > *auto lo* >> > *iface lo inet loopback* >> > >> > *auto eth0* >> > *iface eth0 inet static* >> > * address 192.168.30.14* >> > * netmask 255.255.255.0* >> > * gateway 192.168.30.254* >> > *dns-nameservers 192.168.30.254 4.2.2.2* >> > *#dns-domain cloudstack.et.test.local* >> > --------------------------------------------- >> > >> > B. The KVM host network configuration is a below: >> > >> > Host 1: .10 >> > ----------------------------------------- >> > >> > *# interfaces(5) file used by ifup(8) and ifdown(8)* >> > >> > *auto lo* >> > >> > *iface lo inet loopback* >> > >> > *# The primary network interface* >> > >> > *auto em1* >> > >> > *iface em1 inet manual* >> > >> > >> > *# Public network* >> > >> > * auto cloudbr0* >> > >> > * iface cloudbr0 inet static* >> > >> > * address 192.168.10.12* >> > >> > * network 192.168.10.0* >> > >> > * netmask 255.255.255.0* >> > >> > * gateway 192.168.10.254* >> > >> > * broadcast 192.168.10.255* >> > >> > * dns-nameservers 192.168.10.254 4.2.2.2* >> > >> > * #dns-domain cloudstack.et.test.local* >> > >> > * bridge_ports em1* >> > >> > * bridge_fd 5* >> > >> > * bridge_stp off* >> > >> > * bridge_maxwait 1* >> > >> > >> > *# Private network (not in use for now. Just using 1 bridge)* >> > >> > * auto cloudbr1* >> > >> > * iface cloudbr1 inet manual* >> > >> > * bridge_ports none* >> > >> > * bridge_fd 5* >> > >> > * bridge_stp off* >> > >> > * bridge_maxwait 1* >> > ----------------------------------- >> > >> > >> > Host 2: .30 >> > ----------------------------------- >> > >> > *# interfaces(5) file used by ifup(8) and ifdown(8)* >> > >> > *auto lo* >> > >> > *iface lo inet loopback* >> > >> > *# The primary network interface* >> > >> > *auto em1* >> > >> > *iface em1 inet manual* >> > >> > >> > *# Public network* >> > >> > * auto cloudbr0* >> > >> > * iface cloudbr0 inet static* >> > >> > * address 192.168.30.12* >> > >> > * network 192.168.30.0* >> > >> > * netmask 255.255.255.0* >> > >> > * gateway 192.168.30.254* >> > >> > * broadcast 192.168.30.255* >> > >> > * dns-nameservers 192.168.30.254 4.2.2.2* >> > >> > * #dns-domain cloudstack.et.test.local* >> > >> > * bridge_ports em1* >> > >> > * bridge_fd 5* >> > >> > * bridge_stp off* >> > >> > * bridge_maxwait 1* >> > >> > >> > *# Private network (not in use for now. Just using 1 bridge)* >> > >> > * auto cloudbr1* >> > >> > * iface cloudbr1 inet manual* >> > >> > * bridge_ports none* >> > >> > * bridge_fd 5* >> > >> > * bridge_stp off* >> > >> > * bridge_maxwait 1* >> > >> > ----------------------------------- >> > >> > >> > --John O. Adams >> >> > >
