On Thu, Jul 21, 2011 at 3:13 PM, Sepherosa Ziehau <sepher...@gmail.com> wrote: > > > Hmm, make sure that you have done a full buildkernel instead of quickkernel >
Yes I always do a full buildkernel :-) >Please post following information: >acpidump -t > dfly-bkpsrv# acpidump -t /* RSD PTR: OEM=ACPIAM, ACPI_Rev=1.0x (0) RSDT=0x7dfd0000, cksum=188 */ /* RSDT: Length=52, Revision=1, Checksum=141, OEMID=A M I, OEM Table ID=OEMRSDT, OEM Revision=0x1000624, Creator ID=MSFT, Creator Revision=0x97 Entries={ 0x7dfd0200, 0x7dfd0390, 0x7dfd03f0, 0x7dfde040 } */ /* FACP: Length=132, Revision=2, Checksum=82, OEMID=A M I, OEM Table ID=OEMFACP, OEM Revision=0x1000624, Creator ID=MSFT, Creator Revision=0x97 FACS=0x7dfde000, DSDT=0x7dfd0430 INT_MODEL=APIC Preferred_PM_Profile=Unspecified (0) SCI_INT=9 SMI_CMD=0xb0, ACPI_ENABLE=0xe1, ACPI_DISABLE=0x1e, S4BIOS_REQ=0x0 PSTATE_CNT=0xe2 PM1a_EVT_BLK=0x800-0x803 PM1a_CNT_BLK=0x804-0x805 PM2_CNT_BLK=0x880-0x880 PM_TMR_BLK=0x808-0x80b GPE0_BLK=0x820-0x827 P_LVL2_LAT=101 us, P_LVL3_LAT=1001 us FLUSH_SIZE=1024, FLUSH_STRIDE=16 DUTY_OFFSET=4, DUTY_WIDTH=3 DAY_ALRM=13, MON_ALRM=0, CENTURY=0 IAPC_BOOT_ARCH={LEGACY_DEV,8042} Flags={WBINVD,PROC_C1,SLP_BUTTON,RTC_S4,TMR_VAL_EXT} */ /* FACS: Length=64, HwSig=0x00000000, Firm_Wake_Vec=0x00000000 Global_Lock= Flags= Version=1 */ /* DSDT: Length=14964, Revision=1, Checksum=105, OEMID=1ABZR, OEM Table ID=1ABZRB49, OEM Revision=0xb49, Creator ID=INTL, Creator Revision=0x2002026 */ /* APIC: Length=92, Revision=1, Checksum=174, OEMID=A M I, OEM Table ID=OEMAPIC, OEM Revision=0x1000624, Creator ID=MSFT, Creator Revision=0x97 Local APIC ADDR=0xfee00000 Flags={PC-AT} Type=Local APIC ACPI CPU=1 Flags={ENABLED} APIC ID=0 Type=Local APIC ACPI CPU=2 Flags={DISABLED} APIC ID=129 Type=IO APIC APIC ID=1 INT BASE=0 ADDR=0x00000000fec00000 Type=INT Override BUS=0 IRQ=0 INTR=2 Flags={Polarity=conforming, Trigger=conforming} Type=INT Override BUS=0 IRQ=9 INTR=21 Flags={Polarity=active-lo, Trigger=level} */ /* MCFG: Length=60, Revision=1, Checksum=118, OEMID=A M I, OEM Table ID=OEMMCFG, OEM Revision=0x1000624, Creator ID=MSFT, Creator Revision=0x97 Base Address= 0x00000000e0000000 Segment Group= 0x0000 Start Bus= 0 End Bus= 255 */ acpidump: RSDT entry 3 (sig OEMB) is corrupt dfly-bkpsrv# >enable boot_versbose and post the dmesg before the panic > Copyright (c) 2003-2011 The DragonFly Project. Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. Slab ZoneSize set to 128KB Leaving critical section, allowing interrupts ACPI SDT: RSDP in BIOS mem ACPI FADT: SCI irq 9, conform/conform DragonFly v2.11.0.247.gda17d9-DEVELOPMENT #36: Mon May 23 12:57:37 IST 2011 root@dfly-bkpsrv.hifxnx.local:/usr/obj/usr/src/sys/GENERIC Calibrating clock(s) ... TSC clock: 2193650213 Hz, i8254 clock: 1193201 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency CLK_USE_TSC_CALIBRATION not specified - using old calibration method CPU: AMD Athlon(tm) 64 Processor 3400+ (2193.63-MHz 686-class CPU) Origin = "AuthenticAMD" Id = 0x20ff2 Stepping = 2 Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2> Features2=0x1<SSE3> AMD Features=0xe2500800<SYSCALL,NX,MMX+,FFXSR,LM,3DNow!+,3DNow!> AMD Features2=0x1<LAHF> Data TLB: 32 entries, fully associative Instruction TLB: 32 entries, fully associative L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L2 internal cache: 512 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative WARNING: This architecture revision has known SMP hardware bugs which may cause random instability real memory = 2113336320 (2015 MB) Physical memory chunk(s): 0x00001000 - 0x0009efff, 647168 bytes (158 pages) 0x009fd000 - 0x7dfaffff, 2103128064 bytes (513459 pages) avail memory = 2029371392 (1935 MB) ELCR Found. ISA IRQs programmed as: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 E E E E L L E E E E L L E E E E bios32: Found BIOS32 Service Directory header at 0xc00f0000 bios32: Entry = 0xf0010 (c00f0010) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0x31 pnpbios: Found PnP BIOS data at 0xc00f5860 pnpbios: Entry = f0000:664a Rev = 1.0 Other BIOS signatures found: ndepotmags=438 x mag_cap=128 for mbuf ndepotmags=4 x mag_cap=33 for mbuf pkt hdr ndepotmags=27 x mag_cap=128 for cluster mbuf ndepotmags=27 x mag_cap=128 for jcluster mbuf ndepotmags=27 x mag_cap=128 for mbuf + cluster ndepotmags=4 x mag_cap=33 for mbuf pkt hdr + cluster ndepotmags=27 x mag_cap=128 for mbuf + jcluster ndepotmags=4 x mag_cap=17 for mbuf pkt hdr + jcluster ndepotmags=4 x mag_cap=33 for CCMS ndepotmags=4 x mag_cap=33 for lwbuf ndepotmags=4 x mag_cap=33 for sf_buf ndepotmags=3 x mag_cap=4 for exec-args Preloaded elf kernel "kernel" at 0xc09ce000. Preloaded elf module "acpi.ko" at 0xc09ce1f4. Preloaded elf module "ahci.ko" at 0xc09ce290. Preloaded elf module "ehci.ko" at 0xc09ce32c. module_register: module pci/ahci already exists! Module pci/ahci failed to register: 17 ndepotmags=4 x mag_cap=9 for thread ndepotmags=4 x mag_cap=33 for dsched-tdio-cache ndepotmags=4 x mag_cap=33 for dsched-tdctx-cache ndepotmags=4 x mag_cap=33 for dsched-diskctx-cache ndepotmags=4 x mag_cap=9 for vmspace ndepotmags=4 x mag_cap=33 for disk-msg-cache ndepotmags=4 x mag_cap=33 for devfs-node-cache ndepotmags=4 x mag_cap=33 for devfs-msg-cache ndepotmags=4 x mag_cap=33 for devfs-dev-cache FQ scheduler policy version 1.0 loaded ndepotmags=4 x mag_cap=33 for propdict ndepotmags=4 x mag_cap=33 for propstng ndepotmags=4 x mag_cap=33 for pdict128 ndepotmags=4 x mag_cap=33 for propdata ndepotmags=4 x mag_cap=33 for pdict32 ndepotmags=4 x mag_cap=33 for proparay ndepotmags=4 x mag_cap=33 for pdict16 ndepotmags=4 x mag_cap=33 for propnmbr ndepotmags=4 x mag_cap=9 for devfs ndepotmags=4 x mag_cap=33 for devfs-rule-cache wlan: <802.11 Link Layer> ndepotmags=4 x mag_cap=33 for ata_request ndepotmags=4 x mag_cap=33 for ata_composite No policy for md0 specified, or policy not found disk scheduler: set policy of md0 to noop md0: Malloc disk kbd: new array size 4 kbd1 at kbdmux0 ndepotmags=4 x mag_cap=33 for crypto op ndepotmags=4 x mag_cap=33 for crypto desc crypto: <crypto core> Pentium Pro MTRR support enabled md0: invalid primary partition table: no magic Math emulator present ACPI: RSDP 0xf96f0 00014 (v0 ACPIAM) ACPI: RSDT 0x7dfd0000 00034 (v1 A M I OEMRSDT 01000624 MSFT 00000097) ACPI: FACP 0x7dfd0200 00084 (v2 A M I OEMFACP 01000624 MSFT 00000097) ACPI: DSDT 0x7dfd0430 03A74 (v1 1ABZR 1ABZRB49 00000B49 INTL 02002026) ACPI: FACS 0x7dfde000 00040 ACPI: APIC 0x7dfd0390 0005C (v1 A M I OEMAPIC 01000624 MSFT 00000097) ACPI: MCFG 0x7dfd03f0 0003C (v1 A M I OEMMCFG 01000624 MSFT 00000097) ACPI: OEMB 0x7dfde040 00056 (v1 A M I AMI_OEM 01000624 MSFT 00000097) npx0.nexus0.root0 npx0: <math processor> [tentative] on motherboard npx0: INT 16 interface Using XMM optimized bcopy/copyin/copyout npx0: <math processor> [attached!] on motherboard cryptosoft0.nexus0.root0 cryptosoft0: <software crypto> [tentative] on motherboard crypto: assign cryptosoft0 driver id 0, flags 234881024 crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 23 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0 crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0 cryptosoft0: <software crypto> [attached!] on motherboard acpi0.nexus0.root0 acpi0: <A M I OEMRSDT> [tentative] on motherboard ndepotmags=4 x mag_cap=33 for Acpi-Namespace ndepotmags=4 x mag_cap=33 for Acpi-State ndepotmags=4 x mag_cap=33 for Acpi-Parse ndepotmags=4 x mag_cap=33 for Acpi-ParseExt ndepotmags=4 x mag_cap=33 for Acpi-Operand ACPI FADT: SCI testing interrupt mode ... ACPI FADT: SCI testing level/low ICU: irq 9, edge -> level ACPI FADT: SCI select level/low ACPI: Executed 1 blocks of module-level executable AML code objcache_reclaimlist objcache_reclaimlist objcache_reclaimlist objcache_reclaimlist acpi0: Power Button (fixed) Warning: ACPI is disabling APM's device. You can't run both ACPI timer looks GOOD min = 5, max = 7, width = 2 ACPI timer looks GOOD min = 5, max = 7, width = 2 ACPI timer looks GOOD min = 5, max = 7, width = 2 ACPI timer looks GOOD min = 5, max = 7, width = 2 ACPI timer looks GOOD min = 5, max = 7, width = 2 ACPI timer looks GOOD min = 5, max = 7, width = 2 ACPI timer looks GOOD min = 5, max = 7, width = 2 ACPI timer looks GOOD min = 5, max = 7, width = 2 ACPI timer looks GOOD min = 5, max = 7, width = 2 ACPI timer looks BAD min = 5, max = 1303, width = 1298 acpi_timer0.acpi0.nexus0.root0 acpi_timer0: <32-bit timer at 3.579545MHz> [tentative] port 0x808-0x80b on acpi0 acpi_timer0: <32-bit timer at 3.579545MHz> [attached!] port 0x808-0x80b on acpi0 pci_link0: Index IRQ Rtd Ref IRQs Initial Probe 0 5 N 0 3 4 5 7 10 11 12 14 15 Validation 0 5 N 0 3 4 5 7 10 11 12 14 15 After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15 pci_link1: Index IRQ Rtd Ref IRQs Initial Probe 0 10 N 0 3 4 5 7 10 11 12 14 15 Validation 0 10 N 0 3 4 5 7 10 11 12 14 15 After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15 pci_link2: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 3 4 5 7 10 11 12 14 15 Validation 0 255 N 0 3 4 5 7 10 11 12 14 15 After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15 pci_link3: Index IRQ Rtd Ref IRQs Initial Probe 0 4 N 0 3 4 5 7 10 11 12 14 15 Validation 0 4 N 0 3 4 5 7 10 11 12 14 15 After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15 pci_link4: Index IRQ Rtd Ref IRQs Initial Probe 0 15 N 0 3 4 5 7 10 11 12 14 15 Validation 0 15 N 0 3 4 5 7 10 11 12 14 15 After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15 pci_link5: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 9 Validation 0 255 N 0 9 After Disable 0 255 N 0 9 pci_link6: Index IRQ Rtd Ref IRQs Initial Probe 0 5 N 0 3 4 5 7 10 11 12 14 15 Validation 0 5 N 0 3 4 5 7 10 11 12 14 15 After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15 pci_link7: Index IRQ Rtd Ref IRQs Initial Probe 0 11 N 0 3 4 5 7 10 11 12 14 15 Validation 0 11 N 0 3 4 5 7 10 11 12 14 15 After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15 pci_open(1): mode 1 addr port (0x0cf8) is 0x80012814 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=59501002) pcibios: BIOS version 3.00 pcib0.acpi0.nexus0.root0 pcib0: <ACPI Host-PCI bridge> [tentative] port 0xcf8-0xcff on acpi0 ACPI: Found matching pin for 0.20.INTA at func 1: 255 ACPI: Found matching pin for 0.20.INTA at func 2: 5 ACPI: Found matching pin for 0.18.INTA at func 0: 5 ACPI: Found matching pin for 0.17.INTA at func 0: 11 ACPI: Found matching pin for 0.19.INTA at func 0: 4 pci0.pcib0.acpi0.nexus0.root0 pci0: <ACPI PCI bus> [tentative] on pcib0 pci0: domain=0, physical bus=0 found-> vendor=0x1002, dev=0x5950, revid=0x10 domain=0, bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2220, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1002, dev=0x5a3f, revid=0x00 domain=0, bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns) found-> vendor=0x1002, dev=0x437a, revid=0x80 domain=0, bus=0, slot=17, func=0 class=01-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 MSI supports 1 message map[10]: type I/O Port, range 32, base 0xb800, size 3, enabled map[14]: type I/O Port, range 32, base 0xb400, size 2, enabled map[18]: type I/O Port, range 32, base 0xb000, size 3, enabled map[1c]: type I/O Port, range 32, base 0xa800, size 2, enabled map[20]: type I/O Port, range 32, base 0xa400, size 4, enabled map[24]: type Memory, range 32, base 0xfe9fbc00, size 9, enabled pcib0: matched entry for 0.17.INTA (src \\_SB_.LNKH:0) pcib0: slot 17 INTA routed to irq 11 via \\_SB_.LNKH found-> vendor=0x1002, dev=0x4379, revid=0x80 domain=0, bus=0, slot=18, func=0 class=01-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 powerspec 2 supports D0 D1 D2 D3 current D0 MSI supports 1 message map[10]: type I/O Port, range 32, base 0xa000, size 3, enabled map[14]: type I/O Port, range 32, base 0x9800, size 2, enabled map[18]: type I/O Port, range 32, base 0x9400, size 3, enabled map[1c]: type I/O Port, range 32, base 0x9000, size 2, enabled map[20]: type I/O Port, range 32, base 0x8800, size 4, enabled map[24]: type Memory, range 32, base 0xfe9fb800, size 9, enabled pcib0: matched entry for 0.18.INTA (src \\_SB_.LNKG:0) pcib0: slot 18 INTA routed to irq 5 via \\_SB_.LNKG found-> vendor=0x1002, dev=0x4374, revid=0x80 domain=0, bus=0, slot=19, func=0 class=0c-03-10, hdrtype=0x00, mfdev=1 cmdreg=0x0117, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=4 MSI supports 1 message map[10]: type Memory, range 32, base 0xfe9fa000, size 12, enabled pcib0: matched entry for 0.19.INTA (src \\_SB_.LNKD:0) pcib0: slot 19 INTA routed to irq 4 via \\_SB_.LNKD found-> vendor=0x1002, dev=0x4375, revid=0x80 domain=0, bus=0, slot=19, func=1 class=0c-03-10, hdrtype=0x00, mfdev=0 cmdreg=0x0117, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=4 MSI supports 1 message map[10]: type Memory, range 32, base 0xfe9f9000, size 12, enabled pcib0: matched entry for 0.19.INTA (src \\_SB_.LNKD:0) pcib0: slot 19 INTA routed to irq 4 via \\_SB_.LNKD found-> vendor=0x1002, dev=0x4373, revid=0x80 domain=0, bus=0, slot=19, func=2 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0117, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=4 powerspec 2 supports D0 D1 D2 D3 current D0 MSI supports 1 message map[10]: type Memory, range 32, base 0xfe9f8000, size 12, enabled pcib0: matched entry for 0.19.INTA (src \\_SB_.LNKD:0) pcib0: slot 19 INTA routed to irq 4 via \\_SB_.LNKD found-> vendor=0x1002, dev=0x4372, revid=0x81 domain=0, bus=0, slot=20, func=0 class=0c-05-00, hdrtype=0x00, mfdev=1 cmdreg=0x0403, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type I/O Port, range 32, base 0xb00, size 4, enabled map[14]: type Memory, range 32, base 0, size 10, enabled found-> vendor=0x1002, dev=0x4376, revid=0x80 domain=0, bus=0, slot=20, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 MSI supports 1 message map[20]: type I/O Port, range 32, base 0xff00, size 4, enabled found-> vendor=0x1002, dev=0x437b, revid=0x01 domain=0, bus=0, slot=20, func=2 class=04-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0410, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type Memory, range 64, base 0xfe9e8000, size 14, enabled pcib0: matched entry for 0.20.INTA (src \\_SB_.LNKA:0) pcib0: slot 20 INTA routed to irq 5 via \\_SB_.LNKA found-> vendor=0x1002, dev=0x4377, revid=0x80 domain=0, bus=0, slot=20, func=3 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x010f, statreg=0x0220, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1002, dev=0x4371, revid=0x80 domain=0, bus=0, slot=20, func=4 class=06-04-01, hdrtype=0x01, mfdev=1 cmdreg=0x0107, statreg=0x02a0, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1100, revid=0x00 domain=0, bus=0, slot=24, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1101, revid=0x00 domain=0, bus=0, slot=24, func=1 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1102, revid=0x00 domain=0, bus=0, slot=24, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1103, revid=0x00 domain=0, bus=0, slot=24, func=3 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) pcib1.pci0.pcib0.acpi0.nexus0.root0 pcib1: <ACPI PCI-PCI bridge> [tentative] at device 1.0 on pci0 pcib1: domain 0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xd000-0xdfff pcib1: memory decode 0xfea00000-0xfeafffff pcib1: prefetched decode 0xf8000000-0xfbffffff ACPI: Found matching pin for 1.5.INTA at func 0: 10 pci1.pcib1.pci0.pcib0.acpi0.nexus0.root0 pci1: <ACPI PCI bus> [tentative] on pcib1 pci1: domain=0, physical bus=1 found-> vendor=0x1002, dev=0x5974, revid=0x00 domain=0, bus=1, slot=5, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Prefetchable Memory, range 32, base 0xf8000000, size 26, enabled pcib1: requested memory range 0xf8000000-0xfbffffff: good map[14]: type I/O Port, range 32, base 0xd800, size 8, enabled pcib1: requested I/O range 0xd800-0xd8ff: in range map[18]: type Memory, range 32, base 0xfeaf0000, size 16, enabled pcib1: requested memory range 0xfeaf0000-0xfeafffff: good pcib1: matched entry for 1.5.INTA (src \\_SB_.LNKB:0) pcib1: slot 5 INTA routed to irq 10 via \\_SB_.LNKB vgapci0.pci1.pcib1.pci0.pcib0.acpi0.nexus0.root0 vgapci0: <VGA-compatible display> [tentative] port 0xd800-0xd8ff mem 0xfeaf0000-0xfeafffff,0xf8000000-0xfbffffff irq 10 at device 5.0 on pci1 vgapci0: <VGA-compatible display> [attached!] port 0xd800-0xd8ff mem 0xfeaf0000-0xfeafffff,0xf8000000-0xfbffffff irq 10 at device 5.0 on pci1 pci1: <ACPI PCI bus> [attached!] on pcib1 pcib1: <ACPI PCI-PCI bridge> [attached!] at device 1.0 on pci0 atapci0.pci0.pcib0.acpi0.nexus0.root0 atapci0: <ATI IXP400 SATA150 controller> [tentative] port 0xa400-0xa40f,0xa800-0xa803,0xb000-0xb007,0xb400-0xb403,0xb800-0xb807 mem 0xfe9fbc00-0xfe9fbdff irq 11 at device 17.0 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xa400 atapci0: Reserved 0x200 bytes for rid 0x24 type 3 at 0xfe9fbc00 ata2.atapci0.pci0.pcib0.acpi0.nexus0.root0 ata2: <ATA channel 0> [tentative] on atapci0 ata2: SATA connect time=0ms sched_ithd: stray interrupt 7 on cpu 0 ata2: reset tp1 mask=01 ostat0=50 ostat1=00 ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire No policy for ad4 specified, or policy not found disk scheduler: set policy of ad4 to noop ad4: Silicon Image check3 failed ad4: Adaptec check1 failed ad4: LSI (v3) check1 failed ad4: LSI (v2) check1 failed ad4: FreeBSD check1 failed ad4: 476940MB <Seagate ST3500620AS SD1A> at ata2-master SATA150 ad4: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue ata2: <ATA channel 0> [attached!] on atapci0 ata3.atapci0.pci0.pcib0.acpi0.nexus0.root0 ata3: <ATA channel 1> [tentative] on atapci0 ata3: SATA connect time=0ms sched_ithd: stray interrupt 7 on cpu 0 ata3: reset tp1 mask=01 ostat0=50 ostat1=00 ata3: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata3: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire No policy for ad6 specified, or policy not found disk scheduler: set policy of ad6 to noop ad4: type 0xa5, start 63, end = 976773167, size 976773105 : OK ad6: Silicon Image check3 failed ad6: Adaptec check1 failed ad6: LSI (v3) check1 failed ad6: LSI (v2) check1 failed ad6: FreeBSD check1 failed ad6: 476940MB <Seagate ST3500620AS SD1A> at ata3-master SATA150 ad6: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue ata3: <ATA channel 1> [attached!] on atapci0 atapci0: <ATI IXP400 SATA150 controller> [attached!] port 0xa400-0xa40f,0xa800-0xa803,0xb000-0xb007,0xb400-0xb403,0xb800-0xb807 mem 0xfe9fbc00-0xfe9fbdff irq 11 at device 17.0 on pci0 atapci1.pci0.pcib0.acpi0.nexus0.root0 atapci1: <ATI IXP400 SATA150 controller> [tentative] port 0x8800-0x880f,0x9000-0x9003,0x9400-0x9407,0x9800-0x9803,0xa000-0xa007 mem 0xfe9fb800-0xfe9fb9ff irq 5 at device 18.0 on pci0 atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x8800 atapci1: Reserved 0x200 bytes for rid 0x24 type 3 at 0xfe9fb800 ata4.atapci1.pci0.pcib0.acpi0.nexus0.root0 ata4: <ATA channel 0> [tentative] on atapci1 intr 5 at 40001/40000 hz, livelocked limit engaged! ata4: SATA connect time=0ms ata4: reset tp1 mask=01 ostat0=50 ostat1=00 ata4: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata4: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ad6: type 0xa5, start 63, end = 976773167, size 976773105 : OK ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire intr 5 at 40006/20000 hz, in livelock No policy for ad8 specified, or policy not found disk scheduler: set policy of ad8 to noop ad8: Silicon Image check3 failed ad8: Adaptec check1 failed ad8: LSI (v3) check1 failed ad8: LSI (v2) check1 failed ad8: FreeBSD check1 failed ad8: 476940MB <Seagate ST3500418AS CC38> at ata4-master SATA150 ad8: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue ata4: <ATA channel 0> [attached!] on atapci1 ata5.atapci1.pci0.pcib0.acpi0.nexus0.root0 ata5: <ATA channel 1> [tentative] on atapci1 ata5: SATA connect time=0ms ata5: reset tp1 mask=01 ostat0=50 ostat1=00 ata5: stat0=0x50 err=0x01 lsb=0x00 msb=0x00 ata5: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ad8: type 0xa5, start 63, end = 976773167, size 976773105 : OK ata5-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire No policy for ad10 specified, or policy not found disk scheduler: set policy of ad10 to noop ad10: Silicon Image check3 failed ad10: Adaptec check1 failed ad10: LSI (v3) check1 failed ad10: LSI (v2) check1 failed ad10: FreeBSD check1 failed ad10: 476940MB <Seagate ST3500418AS CC38> at ata5-master SATA150 ad10: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue ata5: <ATA channel 1> [attached!] on atapci1 atapci1: <ATI IXP400 SATA150 controller> [attached!] port 0x8800-0x880f,0x9000-0x9003,0x9400-0x9407,0x9800-0x9803,0xa000-0xa007 mem 0xfe9fb800-0xfe9fb9ff irq 5 at device 18.0 on pci0 ohci0.pci0.pcib0.acpi0.nexus0.root0 ohci0: <ATI SB400 USB Controller> [tentative] mem 0xfe9fa000-0xfe9fafff irq 4 at device 19.0 on pci0 ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe9fa000 usb0: OHCI version 1.0, legacy support sched_ithd: stray interrupt 7 on cpu 0 usb0: SMM does not respond, resetting sched_ithd: stray interrupt 7 on cpu 0 sched_ithd: stray interrupt 7 on cpu 0 sched_ithd: stray interrupt 7 on cpu 0 usb0.ohci0.pci0.pcib0.acpi0.nexus0.root0 usb0: <ATI SB400 USB Controller> [tentative] on ohci0 usb0: USB revision 1.0 sched_ithd: stray interrupt 7 on cpu 0 sched_ithd: stray interrupt 7 on cpu 0 sched_ithd: stray interrupt 7 on cpu 0 uhub0.usb0.ohci0.pci0.pcib0.acpi0.nexus0.root0 uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb0 uhub0: 4 ports with 4 removable, self powered sched_ithd: 10 stray interrupts 7 on cpu 0 - there will be no further reports uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb0 usb0: <ATI SB400 USB Controller> [attached!] on ohci0 ohci0: <ATI SB400 USB Controller> [attached!] mem 0xfe9fa000-0xfe9fafff irq 4 at device 19.0 on pci0 ohci1.pci0.pcib0.acpi0.nexus0.root0 ohci1: <ATI SB400 USB Controller> [tentative] mem 0xfe9f9000-0xfe9f9fff irq 4 at device 19.1 on pci0 ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe9f9000 usb1: OHCI version 1.0, legacy support usb1.ohci1.pci0.pcib0.acpi0.nexus0.root0 usb1: <ATI SB400 USB Controller> [tentative] on ohci1 usb1: USB revision 1.0 uhub1.usb1.ohci1.pci0.pcib0.acpi0.nexus0.root0 uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [tentative] on usb1 uhub1: 4 ports with 4 removable, self powered uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> [attached!] on usb1 usb1: <ATI SB400 USB Controller> [attached!] on ohci1 ohci1: <ATI SB400 USB Controller> [attached!] mem 0xfe9f9000-0xfe9f9fff irq 4 at device 19.1 on pci0 ehci0.pci0.pcib0.acpi0.nexus0.root0 ehci0: <ATI SB400 USB 2.0 controller> [tentative] mem 0xfe9f8000-0xfe9f8fff irq 4 at device 19.2 on pci0 ehci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe9f8000 ehci0: Dropped interrupts workaround enabled usb2: EHCI version 1.0 usb2: companion controllers, 4 ports each: usb0 usb1 usb2.ehci0.pci0.pcib0.acpi0.nexus0.root0 usb2: <ATI SB400 USB 2.0 controller> [tentative] on ehci0 usb2: USB revision 2.0 uhub2.usb2.ehci0.pci0.pcib0.acpi0.nexus0.root0 uhub2: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> [tentative] on usb2 uhub2: 8 ports with 8 removable, self powered uhub2: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> [attached!] on usb2 usb2: <ATI SB400 USB 2.0 controller> [attached!] on ehci0 ehci0: <ATI SB400 USB 2.0 controller> [attached!] mem 0xfe9f8000-0xfe9f8fff irq 4 at device 19.2 on pci0 pci0: <serial bus, SMBus> (vendor 0x1002, dev 0x4372) at device 20.0 atapci2.pci0.pcib0.acpi0.nexus0.root0 atapci2: <ATI IXP400 UDMA133 controller> [tentative] port 0xff00-0xff0f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 20.1 on pci0 atapci2: Reserved 0x10 bytes for rid 0x20 type 4 at 0xff00 ata0.atapci2.pci0.pcib0.acpi0.nexus0.root0 ata0: <ATA channel 0> [tentative] on atapci2 atapci2: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci2: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=01 ata0: stat0=0x10 err=0x01 lsb=0x14 msb=0xeb ata0: stat1=0x01 err=0x04 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=10 stat1=01 devices=0x4<ATAPI_MASTER> intr 5 at 19/20000 hz, livelock removed ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA66 cable=80 wire acd0: setting PIO4 on IXP400 chip acd0: setting UDMA66 on IXP400 chip ad10: type 0xa5, start 63, end = 976773167, size 976773105 : OK No policy for acd0 specified, or policy not found disk scheduler: set policy of acd0 to noop acd0: <SONY DVD RW DRU-830A/SS23> DVDR drive at ata0 as master acd0: read 6890KB/s (6890KB/s) write 6890KB/s (6890KB/s), 2048KB buffer, UDMA66 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc ata0: <ATA channel 0> [attached!] on atapci2 ata1.atapci2.pci0.pcib0.acpi0.nexus0.root0 ata1: <ATA channel 1> [tentative] on atapci2 atapci2: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci2: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=03 ostat0=7f ostat1=7f ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: stat0=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: stat1=0x7f err=0x7f lsb=0x7f msb=0x7f ata1: reset tp2 stat0=ff stat1=ff devices=0x0 ata1: <ATA channel 1> [attached!] on atapci2 atapci2: <ATI IXP400 UDMA133 controller> [attached!] port 0xff00-0xff0f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 20.1 on pci0 pci0: <multimedia, HDA> (vendor 0x1002, dev 0x437b) at device 20.2 irq 5 isab0.pci0.pcib0.acpi0.nexus0.root0 isab0: <PCI-ISA bridge> [tentative] at device 20.3 on pci0 isa0.isab0.pci0.pcib0.acpi0.nexus0.root0 isa0: <ISA bus> [tentative] on isab0 isa0: <ISA bus> [attached!] on isab0 isab0: <PCI-ISA bridge> [attached!] at device 20.3 on pci0 pcib2.pci0.pcib0.acpi0.nexus0.root0 pcib2: <ACPI PCI-PCI bridge> [tentative] at device 20.4 on pci0 pcib2: domain 0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0xe000-0xefff pcib2: memory decode 0xfeb00000-0xfebfffff pcib2: no prefetched decode pcib2: Subtractively decoded bridge. ACPI: Found matching pin for 2.0.INTA at func 0: 255 ACPI: Found matching pin for 2.3.INTA at func 0: 255 pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0 pci2: <ACPI PCI bus> [tentative] on pcib2 pci2: domain=0, physical bus=2 found-> vendor=0x1186, dev=0x4c00, revid=0x11 domain=0, bus=2, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x17 (5750 ns), maxlat=0x1f (7750 ns) intpin=a, irq=255 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0, size 14, memory disabled map[14]: type I/O Port, range 32, base 0, size 8, port disabled found-> vendor=0x10ec, dev=0x8169, revid=0x10 domain=0, bus=2, slot=3, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns) intpin=a, irq=255 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type I/O Port, range 32, base 0, size 8, port disabled map[14]: type Memory, range 32, base 0, size 8, memory disabled skc0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0 skc0: <D-Link DGE-530T A1> [tentative] at device 0.0 on pci2 pcib2: skc0 requested memory range 0xfeb00000-0xfebfffff: good skc0: Lazy allocation of 0x4000 bytes rid 0x10 type 3 at 0xfeb00000 pcib2: matched entry for 2.0.INTA (src \\_SB_.LNKE:0) ICU: irq 15, edge -> level pcib2: slot 0 INTA routed to irq 15 via \\_SB_.LNKE sk0.skc0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0 sk0: <Marvell Yukon (0x1)> [tentative] on skc0 sk0: bpf attached sk0: MAC address: 00:11:95:f2:f2:4f miibus0.sk0.skc0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0 miibus0: <MII bus> [tentative] on sk0 e1000phy0.miibus0.sk0.skc0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0 e1000phy0: <Marvell Semiconductor 88E1011 Gigabit PHY> [tentative] on miibus0 e1000phy0: 1000baseT-FDX, 100baseTX-FDX, 100baseTX, 10baseTX-FDX, 10baseTX, auto e1000phy0: <Marvell Semiconductor 88E1011 Gigabit PHY> [attached!] on miibus0 miibus0: <MII bus> [attached!] on sk0 sk0: <Marvell Yukon (0x1)> [attached!] on skc0 skc0: <D-Link DGE-530T A1> [attached!] mem 0xfeb00000-0xfeb03fff irq 15 at device 0.0 on pci2 pcib2: re0 requested I/O range 0xe000-0xefff: in range re0: Lazy allocation of 0x100 bytes rid 0x10 type 4 at 0xe000 re0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0 re0: <RealTek 8110/8169 Gigabit Ethernet> [tentative] port 0xe000-0xe0ff at device 3.0 on pci2 pcib2: re0 requested I/O range 0xe000-0xe0ff: in range pcib2: matched entry for 2.3.INTA (src \\_SB_.LNKE:0) pcib2: slot 3 INTA routed to irq 15 via \\_SB_.LNKE re0: Hardware rev. 0x10000000; MAC ver. 0x04; PCI32 33MHz miibus1.re0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0 miibus1: <MII bus> [tentative] on re0 rgephy0: rev: 2 rgephy0.miibus1.re0.pci2.pcib2.pci0.pcib0.acpi0.nexus0.root0 rgephy0: <8211B/RTL8169S/8110S media interface> [tentative] on miibus1 rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto rgephy0: <8211B/RTL8169S/8110S media interface> [attached!] on miibus1 miibus1: <MII bus> [attached!] on re0 re0: bpf attached re0: MAC address: 00:16:17:20:2a:a6 re0: <RealTek 8110/8169 Gigabit Ethernet> [attached!] port 0xe000-0xe0ff irq 15 at device 3.0 on pci2 pci2: <ACPI PCI bus> [attached!] on pcib2 pcib2: <ACPI PCI-PCI bridge> [attached!] at device 20.4 on pci0 pci0: <ACPI PCI bus> [attached!] on pcib0 pcib0: <ACPI Host-PCI bridge> [attached!] port 0xcf8-0xcff on acpi0 acpi_button0.acpi0.nexus0.root0 acpi_button0: <Power Button> [tentative] on acpi0 acpi_button0: <Power Button> [attached!] on acpi0 unknown: not probed (disabled) sio0: configured irq 3 not in bitmap of probed irqs 0 sio0: irq maps: 0 0 0 0 sio0.acpi0.nexus0.root0 sio0: <16550A-compatible COM port> [tentative] port 0x2f8-0x2ff irq 3 on acpi0 sio0: type 16550A sio0: <16550A-compatible COM port> [attached!] port 0x2f8-0x2ff irq 3 on acpi0 fdc0.acpi0.nexus0.root0 fdc0: <NEC 72065B or clone> [tentative] port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fdc0: <NEC 72065B or clone> [attached!] port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 ppc0: using extended I/O port range ppc0: SPP ppc0.acpi0.nexus0.root0 ppc0: <Standard parallel printer port> [tentative] port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0.ppc0.acpi0.nexus0.root0 ppbus0: <Parallel port bus> [tentative] on ppc0 plip0.ppbus0.ppc0.acpi0.nexus0.root0 plip0: <PLIP network interface> [tentative] on ppbus0 lp0: bpf attached plip0: <PLIP network interface> [attached!] on ppbus0 lpt0.ppbus0.ppc0.acpi0.nexus0.root0 lpt0: <Printer> [tentative] on ppbus0 lpt0: Interrupt-driven port lpt0: <Printer> [attached!] on ppbus0 ppi0.ppbus0.ppc0.acpi0.nexus0.root0 ppi0: <Parallel I/O> [tentative] on ppbus0 ppi0: <Parallel I/O> [attached!] on ppbus0 ppbus0: <Parallel port bus> [attached!] on ppc0 ppc0: <Standard parallel printer port> [attached!] port 0x378-0x37f irq 7 on acpi0 atkbdc0.acpi0.nexus0.root0 atkbdc0: <Keyboard controller (i8042)> [tentative] port 0x64,0x60 irq 1 on acpi0 atkbd0.atkbdc0.acpi0.nexus0.root0 atkbd0: <AT Keyboard> [tentative] flags 0x1 irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000 atkbd0: <AT Keyboard> [attached!] flags 0x1 irq 1 on atkbdc0 psm0: current command byte:0065 (probe0:ata4:0:0:0): error 22 (probe0:ata4:0:0:0): Unretryable Error psm0.atkbdc0.acpi0.nexus0.root0 psm0: <PS/2 Mouse> [tentative] irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3-00, 3 buttons psm0: config:00000000, flags:00000008, packet size:4 psm0: syncmask:08, syncbits:00 psm0: <PS/2 Mouse> [attached!] irq 12 on atkbdc0 atkbdc0: <Keyboard controller (i8042)> [attached!] port 0x64,0x60 irq 1 on acpi0 cpu0.acpi0.nexus0.root0 cpu0: <ACPI CPU> [tentative] on acpi0 cpu_cst0.cpu0.acpi0.nexus0.root0 cpu_cst0: <ACPI CPU C-State> [tentative] on cpu0 cpu_cst0: switching to generic Cx mode cpu_cst0: <ACPI CPU C-State> [attached!] on cpu0 cpu_pst0: Can't get _PCT package - AE_NOT_FOUND cpu0: <ACPI CPU> [attached!] on acpi0 unknown: not probed (disabled) acpi0: <A M I OEMRSDT> [attached!] at port 0x600-0x60f,0x10-0x1f,0x22-0x3f,0x62-0x63,0x65-0x6f,0x72-0x7f,0x80,0x84-0x86,0x88,0x8c-0x8e,0x90-0x9f,0xa2-0xbf,0xb1,0xe0-0xef,0x4d0-0x4d1,0x40b,0x4d6,0xc00-0xc01,0xc14,0xc50-0xc51,0xc52,0xc6c,0xc6f,0xcd4-0xcd5,0xcd6-0xcd7,0xcd8-0xcdf,0x800-0x89f,0x900-0x90f,0x910-0x91f iomem 0-0x9ffff,0xc0000-0xcffff,0xe0000-0xfffff,0x100000-0x7fffffff,0xe0000000-0xefffffff,0xfec00000-0xfec00fff,0xfee00000-0xfee00fff,0xfff80000-0xffffffff irq 9 on motherboard fdc-: fdc0 exists, using next available unit number atkbdc-: atkbdc0 exists, using next available unit number sio-: sio0 exists, using next available unit number sio-: sio1 exists, using next available unit number sio-: sio2 exists, using next available unit number sio-: sio3 exists, using next available unit number ppc-: ppc0 exists, using next available unit number Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 aps_identify: will specify the port ex_isa_identify() isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0 orm0: <Option ROMs> [tentative] at iomem 0xc0000-0xcefff,0xcf000-0xd37ff,0xd3800-0xd7fff on isa0 orm0: <Option ROMs> [attached!] at iomem 0xc0000-0xcefff,0xcf000-0xd37ff,0xd3800-0xd7fff on isa0 pmtimer0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0 pmtimer0 [tentative] on isa0 pmtimer0 [attached!] on isa0 fdc1: cannot reserve I/O port range fdc1 [tentative] failed to probe at port 0x3f0 irq 6 drq 2 on isa0 adv0 [tentative] failed to probe on isa0 bt0: Failed Status Reg Test - ff bt_isa_probe: Probe failed at 0x330 bt0: Failed Status Reg Test - ff bt_isa_probe: Probe failed at 0x334 bt0: Failed Status Reg Test - ff bt_isa_probe: Probe failed at 0x230 bt0: Failed Status Reg Test - ff bt_isa_probe: Probe failed at 0x234 bt0: Failed Status Reg Test - ff bt_isa_probe: Probe failed at 0x130 bt0: Failed Status Reg Test - ff bt_isa_probe: Probe failed at 0x134 bt0 [tentative] failed to probe at port 0x134-0x137 on isa0 aha0: status reg test failed ff aha0: status reg test failed ff aha0: status reg test failed ff aha0: status reg test failed ff aha0: status reg test failed ff aha0: status reg test failed ff aha0 [tentative] failed to probe at port 0x134-0x137 on isa0 aic0 [tentative] failed to probe at port 0x140-0x15f on isa0 atkbdc1: <Keyboard controller (i8042)> [tentative] failed to probe at port 0x60 on isa0 vga0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0 vga0: <Generic ISA VGA> [tentative] at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vga0: <Generic ISA VGA> [attached!] at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0 sc0: <System console> [tentative] at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) sc0: <System console> [attached!] at flags 0x100 on isa0 aps0 [tentative] failed to probe at port 0x1600-0x161e on isa0 lm0 [tentative] failed to probe at port 0x290-0x297 on isa0 it0 [tentative] failed to probe at port 0x290-0x297 on isa0 it1 [tentative] failed to probe at port 0xc00-0xc07 on isa0 it2 [tentative] failed to probe at port 0xd00-0xd07 on isa0 it3 [tentative] failed to probe at port 0x228-0x22f on isa0 wbsio0 [tentative] failed to probe at port 0x2e-0x2f on isa0 wbsio1.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0 wbsio1: <Winbond LPC Super I/O W83627THF rev 0x83> [tentative] at port 0x4e-0x4f on isa0 wbsio1: hardware monitor iobase is 0x600 wbsio1: found unused lm0 at 0x290 with state 0, reusing at 0x600 lm0.isa0.isab0.pci0.pcib0.acpi0.nexus0.root0 lm0: <Winbond W83627THF Hardware Monitor> [tentative] at port 0x600-0x607 on isa0 lm0: <Winbond W83627THF Hardware Monitor> [attached!] at port 0x600-0x607 on isa0 wbsio1: <Winbond LPC Super I/O W83627THF rev 0x83> [attached!] at port 0x4e-0x4f on isa0 sio1: can't drain, serial port might not exist, disabling sio1 [tentative] failed to probe at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio2 [tentative] failed to probe at port 0x2f8 irq 3 on isa0 sio3: not probed (disabled) sio4: not probed (disabled) ppc1: parallel port found at 0x378 ppc1: cannot reserve I/O port range ppc1: <Parallel port> [tentative] failed to probe at port 0x378-0x37f irq 7 on isa0 ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) cs0: not probed (disabled) sn0: not probed (disabled) isa_probe_children: probing PnP devices BIOS Geometries: 0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors 1:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors 2:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors 3:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors 0 accounted for Device configuration finished. ndepotmags=4 x mag_cap=33 for nameibufs ndepotmags=4 x mag_cap=33 for NFS mount ndepotmags=4 x mag_cap=33 for NFS node ndepotmags=4 x mag_cap=65 for vnodes ndepotmags=4 x mag_cap=33 for UFS dirhash faith0: bpf attached lo0: bpf attached ppp0: bpf attached sl0: bpf attached crypto: <crypto device> CAM: Configuring bus: ata0 CAM: Configuring bus: ata1 CAM: Configuring bus: ata2 CAM: Configuring bus: ata3 CAM: Configuring bus: ata4 CAM: Configuring bus: ata5 CAM: Configuring 6 busses CAM: Finished configuring bus: ata0 CAM: Finished configuring bus: ata1 CAM: Finished configuring bus: ata2 CAM: Finished configuring bus: ata3 CAM: Finished configuring bus: ata5 (probe0:ata4:0:0:0): error 6 (probe0:ata4:0:0:0): Unretryable Error (probe0:ata4:0:0:0): error 22 (probe0:ata4:0:0:0): Unretryable Error CAM: Finished configuring bus: ata4 CAM: finished configuring all busses pass0 at ata4 bus 0 target 0 lun 0 pass0: <SONY DVD RW DRU-830A SS23> Removable CD-ROM SCSI-0 device pass0: 66.000MB/s transfers sg0 at ata4 bus 0 target 0 lun 0 sg0: <SONY DVD RW DRU-830A SS23> Removable CD-ROM SCSI-0 device sg0: 66.000MB/s transfers No policy for cd0 specified, or policy not found disk scheduler: set policy of cd0 to noop bootdev: a0200000 type=0 unit=0 slice=2 part=0 major=3 ATA PseudoRAID loaded (cd0:ata4:0:0:0): error 6 (cd0:ata4:0:0:0): Unretryable Error cd0 at ata4 bus 0 target 0 lun 0 cd0: <SONY DVD RW DRU-830A SS23> Removable CD-ROM SCSI-0 device cd0: 66.000MB/s transfers cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed Mounting root from ufs:/dev/ad4s1a tryroot ad4s1a Mounting devfs start_init: trying /sbin/init HAMMER(Backup1) recovery check seqno=7f32a788 HAMMER(Backup1) recovery range 300000000c51d360-300000000c51d360 HAMMER(Backup1) recovery nexto 300000000c51d360 endseqno=7f32a789 HAMMER(Backup1) mounted clean, no recovery needed HAMMER(Backup2) recovery check seqno=4015f3e7 HAMMER(Backup2) recovery range 30000000079e8ad0-30000000079e8ad0 HAMMER(Backup2) recovery nexto 30000000079e8ad0 endseqno=4015f3e8 HAMMER(Backup2) mounted clean, no recovery needed HAMMER(Backup3) recovery check seqno=057a7b4c HAMMER(Backup3) recovery range 3000000017294e80-3000000017294e80 HAMMER(Backup3) recovery nexto 3000000017294e80 endseqno=057a7b4d HAMMER(Backup3) mounted clean, no recovery needed HAMMER(Bkpsrv2Backup1Slave) recovery check seqno=000f05c0 HAMMER(Bkpsrv2Backup1Slave) recovery range 3000000000075bb0-3000000000075bb0 HAMMER(Bkpsrv2Backup1Slave) recovery nexto 3000000000075bb0 endseqno=000f05c1 HAMMER(Bkpsrv2Backup1Slave) mounted clean, no recovery needed Thanks :-) --Siju