Thank you for your reply, Thomas! This is the port summary.
Number of available ports: 4 Port MAC Address Name Driver Status Link 0 00:07:43:5D:4E:60 0000:05:00.4 net_cxgbe down 100 Gbps 1 00:07:43:5D:4E:68 0000:05:00.4_1 net_cxgbe down 100 Gbps 2 00:07:43:5D:51:00 0000:0b:00.4 net_cxgbe down 100 Gbps 3 00:07:43:5D:51:08 0000:0b:00.4_1 net_cxgbe down 100 Gbps Additionally, this is info of one of the ports. ********************* Infos for port 0 ********************* MAC address: 00:07:43:5D:4E:60 Device name: 0000:05:00.4 Driver name: net_cxgbe Firmware-version: not available Connect to socket: 0 memory allocation on the socket: 0 Link status: down Link speed: 100 Gbps Link duplex: full-duplex MTU: 1500 Promiscuous mode: enabled Allmulticast mode: disabled Maximum number of MAC addresses: 1 Maximum number of MAC addresses of hash filtering: 0 VLAN offload: strip off, filter off, extend off, qinq strip off Hash key size in bytes: 40 Redirection table size: 32 Supported RSS offload flow types: ipv4 ipv4-frag ipv4-tcp ipv4-udp ipv4-other ipv6 ipv6-frag ipv6-tcp ipv6-udp ipv6-other user defined 15 user defined 16 user defined 17 Minimum size of RX buffer: 68 Maximum configurable length of RX packet: 9018 Maximum configurable size of LRO aggregated packet: 0 Maximum number of VFs: 256 Current number of RX queues: 1 Max possible RX queues: 114 Max possible number of RXDs per queue: 4096 Min possible number of RXDs per queue: 128 RXDs number alignment: 1 Current number of TX queues: 1 Max possible TX queues: 114 Max possible number of TXDs per queue: 4096 Min possible number of TXDs per queue: 128 TXDs number alignment: 1 Max segment number per packet: 0 Max segment number per MTU/TSO: 0 Best, Danushka On Sat, Apr 10, 2021 at 4:15 AM Thomas Monjalon <tho...@monjalon.net> wrote: > +Cc Chelsio maintainer > > 09/04/2021 19:24, Danushka Menikkumbura: > > Hello, > > > > When I run testpmd on a system with 2 two-port Chelsio T6 NICs, the link > > status is down for all four ports. I use igb_uio as the kernel driver. > > Below is my testpmd commandline and the startup log. > > > > sudo ./build/app/dpdk-testpmd -l 0,1,2,5 -b 81:00.0 -- -i > > > > EAL: Detected 20 lcore(s) > > EAL: Detected 4 NUMA nodes > > EAL: Detected static linkage of DPDK > > EAL: Multi-process socket /var/run/dpdk/rte/mp_socket > > EAL: Selected IOVA mode 'PA' > > EAL: No available 1048576 kB hugepages reported > > EAL: Probing VFIO support... > > EAL: VFIO support initialized > > EAL: Probe PCI driver: net_cxgbe (1425:6408) device: 0000:05:00.4 > (socket 0) > > rte_cxgbe_pmd: Maskless filter support disabled. Continuing > > EAL: Probe PCI driver: net_cxgbe (1425:6408) device: 0000:0b:00.4 > (socket 0) > > rte_cxgbe_pmd: Maskless filter support disabled. Continuing > > Interactive-mode selected > > testpmd: create a new mbuf pool <mb_pool_0>: n=171456, size=2176, > socket=0 > > testpmd: preferred mempool ops selected: ring_mp_mc > > testpmd: create a new mbuf pool <mb_pool_2>: n=171456, size=2176, > socket=2 > > testpmd: preferred mempool ops selected: ring_mp_mc > > Configuring Port 0 (socket 0) > > Port 0: 00:07:43:5D:4E:60 > > Configuring Port 1 (socket 0) > > Port 1: 00:07:43:5D:4E:68 > > Configuring Port 2 (socket 0) > > Port 2: 00:07:43:5D:51:00 > > Configuring Port 3 (socket 0) > > Port 3: 00:07:43:5D:51:08 > > Checking link statuses... > > Done > > testpmd> > > > > Your help is very much appreciated. > > Please run the command "show port summary all" > > > >
