I really suggest using AT2, preferbly from a CVS snapshot no more then a month old. using AT is not recomended anymore, as that driver is not in development anymore and no bug fixes have or will be applied to it.
-- Oded Arbel m-Wise Mobile Solutions [EMAIL PROTECTED] Mobile: +972-67-340014 Tel: +972-9-9581711 (ext: 116) ::.. Unix geek in training: "Insanity is doing the same thing over and over and expecting different results." > -----Original Message----- > From: Ilari Mikkonen [mailto:[EMAIL PROTECTED]] > Sent: Monday, June 10, 2002 10:10 AM > To: [EMAIL PROTECTED] > Subject: Nokia Card Phone as SMSC #2 > > > I still have problems using Nokias card phone as an smsc. The > situation is as follows (and this is a long mail..). > > 1) I can not start Kannel gateway "normally" If I just try to > start the bearerbox, it says: > > 2002-06-10 09:44:42 [0] INFO: Added logfile `kannel.log' with > level `0'. > 2002-06-10 09:44:42 [0] INFO: ---------------------------------------- > 2002-06-10 09:44:42 [0] INFO: Kannel bearerbox II version > 1.1.6 starting > 2002-06-10 09:44:42 [0] INFO: SSL not supported, no SSL > initialization done. > 2002-06-10 09:44:42 [0] DEBUG: HTTP: Opening server at port 13000. > 2002-06-10 09:44:42 [0] DEBUG: Started thread 1 (gwlib/fdset.c:poller) > 2002-06-10 09:44:42 [0] DEBUG: Started thread 2 > (gwlib/http.c:server_thread) > 2002-06-10 09:44:42 [0] DEBUG: Started thread 3 > (gw/bb_http.c:httpadmin_run) > 2002-06-10 09:44:42 [0] DEBUG: starting smsbox connection module > 2002-06-10 09:44:42 [0] DEBUG: Started thread 4 > (gw/bb_boxc.c:smsboxc_run) > 2002-06-10 09:44:43 [0] DEBUG: AT: Command: AT > 2002-06-10 09:44:53 [0] DEBUG: Read from modem: '' > 2002-06-10 09:44:53 [0] DEBUG: AT: Command: AT&F > 2002-06-10 09:44:53 [0] DEBUG: Read from modem: 'AT&F OK' > 2002-06-10 09:44:53 [0] DEBUG: AT: Command: AT > 2002-06-10 09:44:53 [0] DEBUG: Read from modem: 'AT OK' > 2002-06-10 09:44:53 [0] DEBUG: AT: Command: ATE0 > 2002-06-10 09:44:53 [0] DEBUG: Read from modem: 'ATE0 OK' > 2002-06-10 09:44:53 [0] DEBUG: AT: Command: ATI > 2002-06-10 09:44:53 [0] DEBUG: Read from modem: 'Nokia Mobile > Phones OK' > 2002-06-10 09:44:54 [0] DEBUG: AT: Command: ATI1 > 2002-06-10 09:44:54 [0] DEBUG: Read from modem: > '449144920745515 OK' > 2002-06-10 09:44:55 [0] DEBUG: AT: Command: ATI2 > 2002-06-10 09:44:55 [0] DEBUG: Read from modem: 'OK' > 2002-06-10 09:44:56 [0] DEBUG: AT: Command: ATI3 > 2002-06-10 09:45:06 [0] DEBUG: Read from modem: '' > 2002-06-10 09:45:06 [0] ERROR: Failed to create Smsc wrapper > 2002-06-10 09:45:06 [0] PANIC: Cannot start with SMSC > connection failing > > OR it can say: > > 2002-06-07 15:22:05 [0] DEBUG: AT: Command: ATE0 > 2002-06-07 15:22:05 [0] ERROR: read device file > 2002-06-07 15:22:05 [0] ERROR: System error 11: Resource > temporarily unavailable > 2002-06-07 15:22:05 [0] DEBUG: Read from modem: '' > 2002-06-07 15:22:05 [0] ERROR: Failed to create Smsc wrapper > 2002-06-07 15:22:05 [0] PANIC: Cannot start with SMSC > connection failing > > But when I do a following trick it starts: > - run Minicom and give following AT commands to Card Phone: > ATI1, ATI2, ATI3, ATI4 > -Then run bearerbox and smbox normally. > > 2) When I get the bearerbox and smsbox running after few > tricks, I can send a message from Kannel to mobile phone ( by > using sendsms facility ). But I can't send an SMS to Kannel. > The message I send gets stored to the SIM card in Card Phone. > > 3) Few minutes after starting the boxes I get a message: > [1] ERROR: Error reading from fd 22: > [1] ERROR: System error 104: Connection reset by peer > > I'm running Linux Mandrake 8.0 on Industrial Automated > Computer's SBC. It has an 266 MHz NS Geode processor on it ( > = Slow ). Here are the config file s for Kannel. I'm using > version 1.1.6 of Kannel gateway. > > --Kannel.conf-- > > group = core > admin-port = 13000 > wapbox-port = 13002 > smsbox-port = 13004 > admin-password = bus > wdp-interface-name = "*" > log-file = "kannel.log" > log-level = 0 > box-deny-ip = "*.*.*.*" > box-allow-ip = "127.0.0.1;192.168.*.*" > > group = wapbox > bearerbox-host = "192.168.123.180" > > group = smsc > smsc-id = nokiaphone > smsc = at > modemtype = nokiaphone > device = /dev/ttyS16 > > include = "modems.conf" > > group = smsbox > bearerbox-host = "192.168.123.180" > sendsms-port = 13014 > log-file = "smsbox.log" > > group = sms-service > keyword = keyword > text = "sms-service" > > group = sendsms-user > username = username > password = password > > --Modems.conf-- > group = modems > id = nokiaphone > name = "Nokia Phone" > detect-string = "Nokia Mobile Phone" > need-sleep = true > speed = 38400 > keepalive-cmd = "AT+CBC;+CSQ" > > > >
