Please send messages to list so you can have more answers to your issues You need to add allow / deny entries in your config or setup a routing group. check manuals
The max troughput of each link is controlled by your provider. Kannel can't do anything about it. traffic load balancing can do the job |-----------------------------------------------------------------------------------------------------------------| Envíe y Reciba Datos y mensajes de Texto (SMS) hacia y desde cualquier celular y Nextel en el Perú, México y en mas de 180 paises. Use aplicaciones 2 vias via SMS y GPRS online Visitenos en www.perusms.NET www.smsglobal.com.mx y www.pravcom.com On Tue, Dec 16, 2008 at 1:30 AM, Avinash Pawar // Viva <avin...@vivainfomedia.com> wrote: > Thanks a lot for your reply. > > Now i want to increase speed of kannel, hence want to add 3 SMSC. I had > configuared them as follow > > group= smsc > smsc= smpp > smsc-id=smsc1 > host=xxx.xxx.xxx.xxx > port = xxxx > smsc-username=smsc1 > smsc-password=smsc1 > connect-allow-ip = xxx.xxx.xxx.xxx > system-type="SMPP" > address-range="" > transceiver-mode=1 > source-addr-ton=1 > source-addr-npi=0 > dest-addr-ton=1 > dest-addr-npi=1 > msg-id-type =0x00 > allowed-smsc-id=smsc1;smsc3 > preferred-smsc-id=smsc1 > > > > group=smsc > smsc=smpp > smsc-id=smsc2 > host=xxx.xxx.xxx.xxx > port = xxxx > smsc-username=smsc2 > smsc-password=smsc2 > system-type="SMPP" > source-addr-ton=1 > source-addr-npi=0 > dest-addr-ton=1 > dest-addr-npi=1 > msg-id-type=0x00 > throughput=20 > allowed-smsc-id=smsc2;smsc3 > preferred-smsc-id=smsc2 > > > group=smsc > smsc=smpp > smsc-id=smsc3 > host=xxx.xxx.xxx.xxx > port = xxxx > smsc-username=smsc3 > smsc-password=smsc3 > system-type="SMPP" > source-addr-ton=1 > source-addr-npi=0 > dest-addr-ton=1 > dest-addr-npi=1 > throughput=20 > allowed-smsc-id=smsc3;smsc2;smsc1 > preferred-smsc-id=smsc3 > > Now, Will you please tell me that: > > How to check whether msgs are routed through all 3 SMSCs ??? > > How to increase throughput? > > Please HELP ! > > Thanks & Regards > Avinash > > > On Mon, Dec 15, 2008 at 8:25 PM, Alvaro Cornejo <cornejo.alv...@gmail.com> > wrote: >> >> currently it is not supported. You must restart kannel to reload conf >> file modifications >> >> >> |-----------------------------------------------------------------------------------------------------------------| >> Envíe y Reciba Datos y mensajes de Texto (SMS) hacia y desde cualquier >> celular y Nextel >> en el Perú, México y en mas de 180 paises. Use aplicaciones 2 vias via >> SMS y GPRS online >> Visitenos en www.perusms.NET www.smsglobal.com.mx y >> www.pravcom.com >> >> >> >> On Mon, Dec 15, 2008 at 8:13 AM, Avinash Pawar // Viva >> <avin...@vivainfomedia.com> wrote: >> > Dear sir >> > >> > I have few doubts in kannel :- >> > How to apply changes in smskannel.conf on runtime without stopping >> > kannel? >> > >> > I want to add new smsc group & also want to keep changes in throughput >> > as >> > required. >> > >> > Can you please suggest me . >> > >> > Thanks & Regards >> > Avinash >> > > >