No, I'm using mysql for dlr storage since otherwise dlr are lost on
kannel restart
|-----------------------------------------------------------------------------------------------------------------|
Envíe y Reciba Datos y mensajes de Texto (SMS) hacia y desde cualquier
celular y Nextel
en el Perú, México y en mas de 180 paises. Use aplicaciones 2 vias via
SMS y GPRS online
Visitenos en www.perusms.NET www.smsglobal.com.mx y
www.pravcom.com
On Tue, Mar 10, 2009 at 8:15 PM, seikath <[email protected]> wrote:
> Hi,
>
> I am not aware of the store_tools.
> Anyway, I assume you use default kannel store file
> instead of db dlr storage, correct ?
>
>
>
> Alvaro Cornejo wrote:
>> Hi List
>>
>>
>> I've found the following 2 isues:
>>
>> 1) I have several modems for the same operators 10 for op1 and 5 for
>> op2. For some reason, some messages get stuck into kannel queue and
>> are not sent to smsc without restarting kannel. I've used Alex
>> store_tools and verify messages are in queue. All messages are sent
>> using the same code and use AT-SMSCs.
>>
>> 2) When I restart kannel QUEUED messages are sent through only one
>> at-smsc even if messages have a destination smsc-id specified in
>> sendsms url call
>>
>> This is an snippet of the config I have:
>>
>> smsc-id = id1
>> allowed-smsc = id1,id_op1
>>
>> smsc-id = id2
>> allowed-smsc = id2,id_op1
>>
>> smsc-id = id3
>> allowed-smsc = id3,id_op1
>>
>> smsc-id = id4
>> allowed-smsc = id4,id_op2
>>
>> smsc-id = id5
>> allowed-smsc = id5,id_op2
>>
>> etc...
>>
>> Note there is no smsc defined with smsc-id=id_op1 nor id_op2 in config file.
>>
>> When sending the messages I use &smsc-id=id_op1 or id_op2 into url so
>> kannel load-balance through the smsc of corresponding operator and
>> send the message. This works fine until I restart kannel.
>>
>> After kannel reset, All QUEUED messages are sent through ONLY ONE of
>> the smsc without load-balancing between smsc even though there are
>> hundreds of queued messages; however if, at the same time, I send
>> messages to any of the id_op1 or id_op2, this new messages are
>> correctly load-balanced between smsc-at
>>
>> I use:
>>
>> Kannel bearerbox version `1.4.3'. Build `Feb 13 2009 17:32:59',
>> compiler `4.1.2 20070626 (Red Hat 4.1.2-13)'. System Linux, release
>> 2.6.20-1.2962.fc6, version #1 SMP Tue Jun 19 19:27:14 EDT 2007,
>> machine i686. IP 10.10.5.2. Libxml version 2.6.29. Using OpenSSL
>> 0.9.8b 04 May 2006. Compiled with MySQL 5.0.27, using MySQL 5.0.27.
>> Using native malloc.
>>
>>
>> Any ideas?
>>
>>
>> Regards
>>
>> Alvaro
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>> |-----------------------------------------------------------------------------------------------------------------|
>> Envíe y Reciba Datos y mensajes de Texto (SMS) hacia y desde cualquier
>> celular y Nextel
>> en el Perú, México y en mas de 180 paises. Use aplicaciones 2 vias via
>> SMS y GPRS online
>> Visitenos en www.perusms.NET www.smsglobal.com.mx y
>> www.pravcom.com
>>
>>
>>
>
>
