My phone had the messages locked with a pass-key combination. However, the problem persisted even after removing the access-code. Finally, I switched over to a Nokia XPressMusic handset. It worked like a charm. The only problem being that I'm unable to receive any messages using kannel. Will start a new topic for this issue.
Thanks for all those who helped. Regards, Nikhil. On Wed, Jul 8, 2009 at 11:53 PM, Alvaro Cornejo <[email protected]>wrote: > Seems your modem is requesting a PIN number. If so, you need to add > the necessary PIN into modem config or disable the PIN request in the > phone > > Regards > > Alvaro > > |-----------------------------------------------------------------------------------------------------------------| > Envíe y Reciba Datos y mensajes de Texto (SMS) hacia y desde cualquier > celular y Nextel > en el Perú, México y en mas de 180 paises. Use aplicaciones 2 vias via > SMS y GPRS online > Visitenos en www.perusms.NET www.smsglobal.com.mx y > www.pravcom.com > > > > 2009/7/8 Nikos Balkanas <[email protected]>: > > Hi, > > > > Seems bb will read in only the first init-string it finds. Comment out > the > > ATZ line and see what happens. > > > > BR, > > Nikos > > > > ----- Original Message ----- > > From: Nikhil > > To: [email protected] > > Sent: Wednesday, July 08, 2009 4:31 PM > > Subject: Problem Connecting Motorola V3m > > Hi, > > > > I have recently set up Kannel 1.4.3 on a CentOS 5 box. The smsbox.conf > reads > > as follows for my smsbox and modems (works fine with the device unplugged > > since it won't find anything on /dev/ttyACM0) > > > > # Connection for Motorola V3m > > group = smsc > > smsc = at > > modemtype = Motorola > > device = /dev/ttyACM0 > > #My number here > > my-number = 91xxxxxxxx > > connect-allow-ip = 127.0.0.1 > > log-level = 0 > > > > #Modem config for Motorola V3m > > group = modems > > id = Motorola > > name = Motorola_V3m > > detect-string = Motorola > > init-string = "ATZ" > > init-string = "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" > > > > When I try to start the bearerbox with "sudo /usr/local/sbin/bearerbox > > smsbox.conf", it fails to initialise my device. Excerpts from the debug > log > > are as follows: > > > > 08 18:40:16 [23574] [0] INFO: Kannel bearerbox II version 1.4.3 starting > > 2009-07-08 18:40:16 [23574] [0] INFO: MAIN: Start-up done, entering > > mainloop > > 2009-07-08 18:40:16 [23574] [0] DEBUG: smsc_fake: start > > called > > 2009-07-08 18:40:16 [23574] [0] DEBUG: AT2[/dev/ttyACM0]: start > > called > > 2009-07-08 18:40:16 [23574] [7] DEBUG: Thread 7 > > (gw/smsc/smsc_at.c:at2_device_thread) maps to pid > > 23574. > > 2009-07-08 18:40:16 [23574] [7] INFO: AT2[/dev/ttyACM0]: trying to use > speed > > <9600> from modem > > definition > > 2009-07-08 18:40:16 [23574] [7] INFO: AT2[/dev/ttyACM0]: opening > > device > > 2009-07-08 18:40:16 [23574] [8] DEBUG: Thread 8 > > (gw/bb_smscconn.c:sms_router) maps to pid > > 23574. > > 2009-07-08 18:40:16 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: device opened. > > Telnet mode = > > 0 > > 2009-07-08 18:40:16 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: device > > opened > > 2009-07-08 18:40:16 [23574] [7] INFO: AT2[/dev/ttyACM0]: speed set to > > 9600 > > 2009-07-08 18:40:16 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: --> > > ^M > > 2009-07-08 18:40:18 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: --> > > AT^M > > 2009-07-08 18:40:18 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: <-- > > OK > > 2009-07-08 18:40:18 [23574] [7] INFO: AT2[/dev/ttyACM0]: Closing > > device > > 2009-07-08 18:40:18 [23574] [7] INFO: AT2[/dev/ttyACM0]: speed is > > 9600 > > 2009-07-08 18:40:18 [23574] [7] INFO: AT2[/dev/ttyACM0]: opening > > device > > 2009-07-08 18:40:18 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: device opened. > > Telnet mode = > > 0 > > 2009-07-08 18:40:18 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: device > > opened > > 2009-07-08 18:40:18 [23574] [7] INFO: AT2[/dev/ttyACM0]: Logging > > in > > 2009-07-08 18:40:18 [23574] [7] INFO: AT2[/dev/ttyACM0]: init > > device > > 2009-07-08 18:40:18 [23574] [7] INFO: AT2[/dev/ttyACM0]: speed set to > > 9600 > > 2009-07-08 18:40:18 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: --> > > ATZ^M > > 2009-07-08 18:40:18 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: <-- > > OK > > 2009-07-08 18:40:18 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: --> > > AT^M > > 2009-07-08 18:40:18 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: <-- > > AT > > 2009-07-08 18:40:18 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: <-- > > OK > > 2009-07-08 18:40:18 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: --> > > AT&F^M > > 2009-07-08 18:40:19 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: <-- > > AT&F > > 2009-07-08 18:40:19 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: <-- > > OK > > 2009-07-08 18:40:19 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: --> > > ATE0^M > > 2009-07-08 18:40:19 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: <-- > > ATE0 > > 2009-07-08 18:40:19 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: <-- > > OK > > 2009-07-08 18:40:19 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: --> > > AT+IFC=2,2^M > > 2009-07-08 18:40:19 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: <-- > > OK > > 2009-07-08 18:40:19 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: --> > > AT+CPIN?^M > > 2009-07-08 18:40:19 [23574] [7] DEBUG: AT2[/dev/ttyACM0]: <-- > > ERROR > > 2009-07-08 18:40:19 [23574] [7] ERROR: AT2[/dev/ttyACM0]: Generic error: > > ERROR > > 2009-07-08 18:40:19 [23574] [7] ERROR: AT2[/dev/ttyACM0]: Initialization > of > > device > > failed. > > 2009-07-08 18:40:19 [23574] [7] INFO: AT2[/dev/ttyACM0]: Closing > > device > > 2009-07-08 18:40:19 [23574] [7] ERROR: AT2[/dev/ttyACM0]: Couldn't > connect > > (retrying in 10 seconds). > > > > And it goes in a loop after that. As seen above, it fails to fetch a > valid > > response for AT+CPIN command on my device. Also, I got the init-string > > values from wvdial.conf under /etc directory. Would be glad if anybody > could > > point out something that is causing this problem. > > -- > > Regards > > Nikhil Lanjewar > > > -- Regards Nikhil Lanjewar
