Use user list for this kind of requests. You should check your modems specs to see if that is possible.
Regards Alvaro On Sat, Nov 21, 2009 at 12:22 PM, emocanos <[email protected]> wrote: > > hi, > thank you for your reply. I found that as a problem: On some type huawei > when we enter the above command - and get an answer just OK. The problem is > that the modem sends the response to another port. BUT! we can get. we run > two terminals: one for the modem port, as described above, the second - the > port device 3G PC UI Interface: cat / dev/ttyUSB1 (the port number in the > list of COM ports in Manager device, it is usually more than 1 modem port > number). Then type the command in the Modem Port Terminal minicom: AT + USDc > = 1, "* 111 # * xxxxxxxxxxxx", 15 - a couple of seconds see the answer in > the window of the second terminal, 3G PC UI Interface. > So how to redirect the output to kannel? > > > Alvaro Cornejo wrote: >> >> You should add this command to the init string and kannel will issue >> the command ONCE at startup. >> >> Else you can add that command to the keepalive string and kannel will >> send this command to the modem at the specified keepalive interval. >> >> For viewing/monitoring the results, you must set the log level to 0 >> (debug) and have an application that will monitor that log in realtime >> and take necessary actions if the balance drop below your settings. >> >> Else you can patch kannel to report that commad in another way you >> want. In this case you will branch-off kannel, but you can submit your >> patch to kannel in order to have devel group validate it and evaluate >> if the kannel main branch can benefit of that patch. >> >> Regards >> >> Alvaro >> >> On Sat, Nov 21, 2009 at 10:29 AM, emocanos <[email protected]> wrote: >>> >>> For sending SMS, I use kannel, which installs as a daemon taking control >>> of >>> GSM modem huawei e220. SIM card installed in the modem is a prepaid card. >>> in this case I want to add code to monitor the credit card. and issue a >>> warning if it falls too low. >>> type sends commands to the modem using the AT command CUSD. Are tested >>> immediately with minicom: >>> >>> AT + CUSD = 1 * 222 #, 15 >>> OK >>> normally after this OK I have a message like this >>> + CUSD: 2, "Current Credit: 00.00 DA", 15 >>> >>> but I will have no result >>> I do not know what the problem is and if there Is there a solution >>> >>> thank you for answer >>> -- >>> View this message in context: >>> http://old.nabble.com/Check-the-credit-card-SIM-tp26457505p26457505.html >>> Sent from the Kannel - Dev mailing list archive at Nabble.com. >>> >>> >>> >> >> >> >> -- >> |-----------------------------------------------------------------------------------------------------------------| >> Envíe y Reciba Datos y mensajes de Texto (SMS) hacia y desde cualquier >> celular y Nextel >> en el Perú, México y en mas de 180 paises. Use aplicaciones 2 vias via >> SMS y GPRS online >> Visitenos en www.perusms.NET www.smsglobal.com.mx y >> www.pravcom.com >> >> >> > > -- > View this message in context: > http://old.nabble.com/Check-the-credit-card-SIM-tp26457505p26458475.html > Sent from the Kannel - Dev mailing list archive at Nabble.com. > > > -- |-----------------------------------------------------------------------------------------------------------------| Envíe y Reciba Datos y mensajes de Texto (SMS) hacia y desde cualquier celular y Nextel en el Perú, México y en mas de 180 paises. Use aplicaciones 2 vias via SMS y GPRS online Visitenos en www.perusms.NET www.smsglobal.com.mx y www.pravcom.com
