yes getting an entry in modem log(ttyUSB1.log) of kannel like 2014-06-04 10:35:49 [32020] [7] DEBUG: AT2[ttyUSB1]: <-- RING 2014-06-04 10:35:49 [32020] [7] DEBUG: AT2[ttyUSB1]: --> ATH0^M 2014-06-04 10:35:49 [32020] [7] DEBUG: AT2[ttyUSB1]: <-- OK
But not getting incoming call number.......... regards abhi On Tue, Jun 3, 2014 at 9:23 PM, Alvaro Cornejo <[email protected]> wrote: > Hi > > Check your modem log --in debug mode--. If call "hits" your modem you > should see at least one ring entry. Note that there is an AT command > to tell the modem to drop any incoming call at the first ring... sorry > didn't remember which... getting to my 50ties :) > > It might also be that your SIM (operator configuration) does not allow > voice calls. Try moving sim to a standard phone a test calling from > /to that device and/or talk to your operator to see if voice calls are > allowed on your sim. > > You can also try the opposite: Put the working sim from your phone to > the modem and try to call it. > > Regards > > Alvaro > > > > |-----------------------------------------------------------------------------------------------------------------| > Envíe y Reciba Datos y mensajes de Texto (SMS) hacia y desde cualquier > celular y Nextel > en el Perú, México y en mas de 180 paises. Use aplicaciones 2 vias via > SMS y GPRS online > Visitenos en www.perusms.com > > > On Tue, Jun 3, 2014 at 10:28 AM, Alok Srivastava <[email protected]> > wrote: > > thanks Alvaro for ur help, actually i was not saying ring on modem, > > i was not listening any ring on my mobile when i m calling any number of > > modem. > > when i call a number of modem from my mobile no, it just cut off the > phone. > > when i stop kannel, ring goes properly.................... > > i want call can also be handled with kannel.............but problem is > that > > call is not going on modem's number > > when kannel is running. > > > > Regards > > Abhi > > > > > > On Tue, Jun 3, 2014 at 7:18 PM, Alvaro Cornejo <[email protected] > > > > wrote: > >> > >> Hi > >> > >> Modems usually does not have speakers; therefore you will not hear any > >> ring; however if you have your logs in debug mode, you will see a > >> "ring" entry on it. You might also need to set your modem to verbose > >> messages (AT+CMEE). Also, if you want to 'see' the caller number along > >> the 'ring' entry, you need to enable that in modem configuration. I > >> think command AT+CLI is the one does that. You need to add it to modem > >> init config. Check AT command set info for details. > >> > >> As for receiving a sms with the caller information, kannel does not do > >> it. You can patch it in order to do that or you can parse kannel log > >> in order to get that information and send the sms. > >> > >> Regards > >> > >> Alvaro > >> > >> > >> > >> > |-----------------------------------------------------------------------------------------------------------------| > >> Envíe y Reciba Datos y mensajes de Texto (SMS) hacia y desde cualquier > >> celular y Nextel > >> en el Perú, México y en mas de 180 paises. Use aplicaciones 2 vias via > >> SMS y GPRS online > >> Visitenos en www.perusms.com > >> > >> > >> On Tue, Jun 3, 2014 at 4:22 AM, Alok Srivastava <[email protected]> > wrote: > >> > Actually not getting any ring when try to calling on numbers of modem. > >> > > >> > Regards > >> > > >> > > >> > On Tue, Jun 3, 2014 at 2:47 PM, Alok Srivastava <[email protected]> > >> > wrote: > >> >> > >> >> Dear list > >> >> > >> >> Plz help > >> >> i am using wavecom 16 port modem for incoming messages, using sqlbox > >> >> getting messages properly, but there is a requirement if somebody > >> >> calling on > >> >> numbers of modem i want a sms message on my mobile that "incoming > call > >> >> from > >> >> this number 91XXXXXXXXXX". > >> >> Is it Possible. > >> >> Please Help > >> >> > >> >> Regards > >> >> Abhi > >> > > >> > > > > > >
