Great, this was useful.. So now I am correctly registered (as you can see here) but I can't ping any other EID, and I can't neither ping it from my other LISP site.
Again, thanks for the help. Daniele On 15/mag/2013, at 12:55, Albert López wrote: > This information should be in the mail that Lori sent to you with the > configuration information, key,... > You can check the map-server that you should use here. Search your EID and in > the first column you will find the Map-Server that you should use. To get the > ip of the assigned Map-Server you could use "host map-server" where > map-server is the name appearing in the firs column plus rloc.lisp4.net. For > instance: asp-mr-ms -> asp-mr-ms.rloc.lisp4.net > > Regards > > Albert > > On 05/15/2013 12:23 PM, Daniele wrote: >> Inside the lispd.config file I put this address as a map-server/resolver >> address: 193.162.145.50, is that correct? >> >> (I'll check out the lig command) >> >> Kind regards >> Daniele >> >> >> On 15/mag/2013, at 12:15, Albert López wrote: >> >>> May be the problem is a firewall. Try to check if you could get an answer >>> using lig. For instance, you could check if you get answer to: lig -m >>> 195.50.116.18 153.16.10.11 >>> On the other side, you can use wireshark listening to eth0 to see if >>> map-registers are sent and if you receive map-notify. >>> >>> Regards >>> >>> Albert >>> >>> >>> On 05/15/2013 11:10 AM, Daniele wrote: >>>> Thanks Albert for the reply, in this moment i temporarily disabled the >>>> wifi interface to isolate the issue. This is the routing table now: >>>> >>>> Kernel IP routing table >>>> Destination Gateway Genmask Flags Metric Ref Use >>>> Iface >>>> 0.0.0.0 0.0.0.0 128.0.0.0 U 0 0 0 >>>> lispTun0 >>>> 0.0.0.0 151.100.122.1 0.0.0.0 UG 100 0 0 >>>> eth0 >>>> 128.0.0.0 0.0.0.0 128.0.0.0 U 0 0 0 >>>> lispTun0 >>>> 151.100.122.0 0.0.0.0 255.255.255.0 U 0 0 0 >>>> eth0 >>>> 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 >>>> eth0 >>>> 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 >>>> virbr0 >>>> >>>> Now it seems well configured, but i can't ping any EID, and checking in >>>> the lispmon website i don't get any map reply from the London Map Server >>>> looking for my /32 EID. That means I'm not registering.. >>>> I can only ping my subnet, obviously, since it's directly connected to >>>> eth0 interface. >>>> >>>> Thanks >>>> Daniele >>>> >>>> >>>> >>>> On 15/mag/2013, at 10:06, Albert López wrote: >>>> >>>>> Dear Daniele, >>>>> >>>>> The interface you should use in the database-mapping structure of the >>>>> configuration file is the one containing the locators. This interface >>>>> should have a public IP address and a gateway assigned. >>>>> From the information you have provided, the interface eth0 doesn't have a >>>>> default route assigned. You should assign a default route to the >>>>> interface eth0 with a less priority metric than wlan0 (higher number). >>>>> Let us know if this resolve the problem >>>>> >>>>> Regards >>>>> >>>>> Albert L. >>>>> >>>>> On 05/14/2013 07:36 PM, Daniele wrote: >>>>>> >>>>>> >>>>>> What does 'ifconfig -a' show now? >>>>>> >>>>>> -Lori >>>>>> >>>>>> >>>>>> Dear Lori, apparently the interfaces are correctly configured. This is >>>>>> what ifconfig returns while lispd is running (I'd like to use the eth0 >>>>>> interface for LISP and the wireless interface to stay connected to the >>>>>> internet): >>>>>> >>>>>> eth0 Link encap:Ethernet HWaddr 00:1d:ba:1c:ac:27 >>>>>> inet addr:1 <my public IP> Bcast:0.0.0.0 Mask:255.255.255.255 >>>>>> inet6 addr: fe80::21d:baff:fe1c:ac27/64 Scope:Link >>>>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>>>>> RX packets:17974 errors:0 dropped:382 overruns:0 frame:0 >>>>>> TX packets:5260 errors:0 dropped:0 overruns:0 carrier:0 >>>>>> collisions:3 txqueuelen:1000 >>>>>> RX bytes:1757884 (1.7 MB) TX bytes:228362 (228.3 KB) >>>>>> Interrupt:16 >>>>>> >>>>>> lispTun0 Link encap:UNSPEC HWaddr >>>>>> 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 >>>>>> inet addr: <my EID> P-t-P:153.16.44.120 Mask:255.255.255.255 >>>>>> inet6 addr: 2610:d0:ffff:192::1/128 Scope:Global >>>>>> UP POINTOPOINT RUNNING MTU:1440 Metric:1 >>>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 >>>>>> TX packets:2398 errors:0 dropped:0 overruns:0 carrier:0 >>>>>> collisions:0 txqueuelen:500 >>>>>> RX bytes:0 (0.0 B) TX bytes:168268 (168.2 KB) >>>>>> >>>>>> lo Link encap:Local Loopback >>>>>> inet addr:127.0.0.1 Mask:255.0.0.0 >>>>>> inet6 addr: ::1/128 Scope:Host >>>>>> UP LOOPBACK RUNNING MTU:16436 Metric:1 >>>>>> RX packets:7135 errors:0 dropped:0 overruns:0 frame:0 >>>>>> TX packets:7135 errors:0 dropped:0 overruns:0 carrier:0 >>>>>> collisions:0 txqueuelen:0 >>>>>> RX bytes:666361 (666.3 KB) TX bytes:666361 (666.3 KB) >>>>>> >>>>>> virbr0 Link encap:Ethernet HWaddr c2:f8:64:5d:92:1d >>>>>> inet addr:192.168.122.1 Bcast:192.168.122.255 >>>>>> Mask:255.255.255.0 >>>>>> UP BROADCAST MULTICAST MTU:1500 Metric:1 >>>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 >>>>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 >>>>>> collisions:0 txqueuelen:0 >>>>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) >>>>>> >>>>>> wlan0 Link encap:Ethernet HWaddr 00:16:ea:25:f1:70 >>>>>> inet addr:10.0.1.31 Bcast:10.0.1.255 Mask:255.255.255.0 >>>>>> inet6 addr: fe80::216:eaff:fe25:f170/64 Scope:Link >>>>>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 >>>>>> RX packets:7599 errors:0 dropped:0 overruns:0 frame:0 >>>>>> TX packets:6219 errors:0 dropped:0 overruns:0 carrier:0 >>>>>> collisions:0 txqueuelen:1000 >>>>>> RX bytes:5640735 (5.6 MB) TX bytes:1268953 (1.2 MB) >>>>>> >>>>>> >>>>>> Anyway i can't ping any other LISP site, my EID doesn't appear in the >>>>>> London Map Server, and also my wifi connection stops working. I guess it >>>>>> is due to some conflict in the routing table >>>>>> >>>>>> Kernel IP routing table >>>>>> Destination Gateway Genmask Flags Metric Ref Use >>>>>> Iface >>>>>> 0.0.0.0 0.0.0.0 128.0.0.0 U 0 0 0 >>>>>> lispTun0 >>>>>> 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 >>>>>> wlan0 >>>>>> 10.0.1.0 0.0.0.0 255.255.255.0 U 2 0 0 >>>>>> wlan0 >>>>>> 128.0.0.0 0.0.0.0 128.0.0.0 U 0 0 0 >>>>>> lispTun0 >>>>>> 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 >>>>>> wlan0 >>>>>> 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 >>>>>> virbr0 >>>>>> >>>>>> >>>>>> Can wifi and LISP interface live together? Do I have to modify manually >>>>>> the routing table? >>>>>> >>>>>> Thanks >>>>>> Daniele >>>>>> >>>>>> >>>>>> _______________________________________________ >>>>>> Contactus-linux mailing list >>>>>> [email protected] >>>>>> https://lispmob.org/mailman/listinfo/contactus-linux >>>>> >>>>> >>>> >> >
