Hi Gad, The OpenSAF SNMP subagent gets started on both the active and standby controllers. But, only the active controller will provide service i.e. establish the connection with SNMP master agent and responds to SNMP queries.
Pls make sure you are issuing SNMP commands to/on active controller only. I guess in your case you might have issued commands to a stand by controller IP ? Pls confirm. Thanks & Regards, AVM -----Original Message----- From: DaMiEn667 [mailto:[EMAIL PROTECTED] Sent: Wednesday, November 14, 2007 11:54 AM To: ALLA VENKATA MAHESH-TFH648; [email protected] Subject: RE: [Users] Problem with snmpwalk on MontaVista 4.0.1 cge Hi, my snmpd is being started with the -x, -I and -interfaces... however, I noticed that when I switch over to the standby controller (by doing an AV switchover through the CLI), and do the same SNMP commands on controller 2's ip, it works! I have the exact same snmpd configuration on both controllers. I did a 'ps aux' to see how the snmp sub-agent was started and noticed a difference between the 2 controllers: Controller 1's sub-agent was started with: /opt/opensaf/controller/bin/ncs_snmp_subagt While Controller 2's sub-agent was started with: /opt/opensaf/controller/bin/ncs_snmp_subagt ROLE=2 NID_SVC_ID=20 Both of the controllers are started with: /opt/opensaf/controller/scripts/nis_scxb start ncsSnmpSubagt.conf on both controllers: agentxsocket tcp:localhost:705 agentxPingInterval 1 Also, the nodeinit.conf is IDENTICAL on both systems. I'm at a loss... at least I can use the system through the CLI... Thanks for any help! Gad -----Original Message----- From: ALLA VENKATA MAHESH-TFH648 [mailto:[EMAIL PROTECTED] Sent: Monday, November 12, 2007 9:59 PM To: DaMiEn667; [email protected] Subject: RE: [Users] Problem with snmpwalk on MontaVista 4.0.1 cge Hi Gad, Please make sure that you have started master agent (snmpd) with following option ,so that it listens for tcp connections. ./snmpd -x tcp:localhost:705 -I -interfaces And check connections are ESTABLISHED on 705 ports # netstat -apn|grep 705 tcp 0 0 0.0.0.0:705 0.0.0.0:* LISTEN 8259/snmpd tcp 0 0 127.0.0.1:52298 127.0.0.1:705 ESTABLISHED 27860/ncs_snmp_suba tcp 0 0 127.0.0.1:705 127.0.0.1:52298 ESTABLISHED 8259/snmpd Thanks & Regards, AVM ________________________________ From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of DaMiEn667 Sent: Tuesday, November 13, 2007 3:16 AM To: [email protected] Subject: [Users] Problem with snmpwalk on MontaVista 4.0.1 cge Hi guys, I really could use some help here. I've set up, compiled, installed, and successfully started openSAF on 2 controllers (one as Active and one as Standby, both start without any errors). I've been reading up in the forums on how to set variables through snmp, however, none of the examples seem to work for me. They talk about adding a node to the configuration through snmp by issuing the following snmpset commands: snmpset -v2c -c public -m /usr/share/snmp/mibs/SAF-AMF-MIB localhost SAF-AMF-MIB::saAmfNodeSuFailoverProb.\"safNode=SC_2_2\" x "00 00 00 00 05 F5 E1 00" snmpset -v2c -c public -m /usr/share/snmp/mibs/SAF-AMF-MIB localhost SAF-AMF-MIB::saAmfNodeSuFailoverMax.\"safNode=SCL_2_2\" u 2 snmpset -v2c -c public -m /usr/share/snmp/mibs/SAF-AMF-MIB localhost SAF-AMF-MIB::saAmfNodeAdminState.\"safNode=SC_2_2\" i 2 snmpset -v2c -c public -m /usr/share/snmp/mibs/NCS-AVSV-MIB localhost NCS-AVSV-MIB::ncsNDNodeId.\"safNode=SC_2_2\" u 134928 snmpset -v2c -c public -m /usr/share/snmp/mibs/SAF-AMF-MIB localhost SAF-AMF-MIB::saAmfNodeRowStatus.\"safNode=SC_2_2\" i 1 I can run that on either controller (I've even tried changing the safNode= to SC_2_1), I get the same error: Error in packet. Reason: notWritable (That object does not support modification) Failed object: SAF-AMF-MIB::saAmfNodeSuFailoverProb."safNode=SC_2_2" When I try to do an snmpwalk on either controller this is what I get in return: root:~# snmpwalk -v2c -c public -m /usr/share/snmp/mibs/SAF-AMF-MIB localhost SAF-AMF-MIB::saAmfNodeSuFailoverProb.\"safNode=SC_2_2\" SAF-AMF-MIB::saAmfNodeSuFailoverProb."safNode=SC_2_2" = No Such Object available on this agent at this OID I've even tried doing: snmpwalk -v2c -c public -m /usr/share/snmp/mibs/SAF-AMF-MIB localhost SAF-AMF-MIB::saAmfNodeTable which results in: SAF-AMF-MIB::saAmfNodeTable = No Such Object available on this agent at this OID SNMPD is started using the following command on both controllers: /usr/sbin/snmpd -x tcp:localhost:705 -c /usr/share/snmp/snmpd.conf -I -interfaces -Lsd -Lf /dev/null -p /var/run/snmpd.pid Snmpd.conf on both controllers is: # community string to be given in the SNMP requests at SNMP Manager rwcommunity public master agentx #IP address on which snmptrapd/snmp Manager is listening for the traps trap2sink 10.0.0.131 syslocation ECCG syscontact ECCG-SUPPORT sysservices 79 # # Directives for SubAgent communication # agentxTimeout 10 agentxRetries 0 That being said, am I missing something here? Shouldn't I be able to see the 2 controllers as 2 separate ROWS in the saAmfNodeTable? Thanks in advance, Gad _______________________________________________ Users mailing list [email protected] http://list.opensaf.org/maillist/listinfo/users
